interactive scape Scape Pro User manual

Scape® Pro
spr65-006
Operating Manual

1. General
—
Scape® Pro Technical specifications are subject
spr65-006 to change without notice.
Operating Manual Version 1.7 – Status: 04/2020
Page 2 of 27 poc: SFi
Scape® Pro
Operating Manual
Contents
1. General _____________________________________________________________________________________________________________5
1.1. Safety instructions ____________________________________________________________________________________________________5
1.2. Scope of delivery _____________________________________________________________________________________________________7
1.3. Cleaning instructions _________________________________________________________________________________________________7
1.4. Transportation instructions___________________________________________________________________________________________7
2. Specifications and set up___________________________________________________________________________________________8
2.1. Connections and controls____________________________________________________________________________________________ 8
2.1.1. PC unit____________________________________________________________________________________________________________ 8
2.1.2. Connections for power and peripherals___________________________________________________________________________ 9
2.1.3. Touch screen____________________________________________________________________________________________________ 10
2.1.4. Remote control ___________________________________________________________________________________________________ 11
3. Installation ________________________________________________________________________________________________________ 12
3.1. Notes ________________________________________________________________________________________________________________12
3.2. Connection to the power supply _____________________________________________________________________________________12
3.3. Connection to the network __________________________________________________________________________________________12
4. Switching on ______________________________________________________________________________________________________ 13
5. Display settings – OSD ____________________________________________________________________________________________ 14
5.1. OSD usage ___________________________________________________________________________________________________________14
5.2. Select input source __________________________________________________________________________________________________14
6. Integrated PC _____________________________________________________________________________________________________ 15
7. Troubleshooting tips ______________________________________________________________________________________________ 16
7.1. Manufacturer – Support _____________________________________________________________________________________________16
7.2. Problems and solutions ______________________________________________________________________________________________16
8. Appendix __________________________________________________________________________________________________________ 17
8.1. Technical data _______________________________________________________________________________________________________17
8.1.1. Scape® Pro 65 ____________________________________________________________________________________________________17
8.1.2. Touchscreen _____________________________________________________________________________________________________17
8.1.3. Silent-PC 2060 ___________________________________________________________________________________________________18

1. General
—
Scape® Pro Technical specifications are subject
spr65-006 to change without notice.
Operating Manual Version 1.7 – Status: 04/2020
Page 3 of 27 poc: SFi
8.2. Technical drawings_________________________________________________________________________________________________ 20
8.2.1. Perspective______________________________________________________________________________________________________ 20
8.2.2. Top view _________________________________________________________________________________________________________21
8.2.3. Front view_______________________________________________________________________________________________________ 22
8.2.4. Right view_______________________________________________________________________________________________________ 23
8.2.5. Detail – Tube with table legs ____________________________________________________________________________________ 24
8.2.6. Detail – Tube____________________________________________________________________________________________________ 25
8.2.7. Detail – Tube connections ______________________________________________________________________________________ 26

1. General
—
Scape® Pro Technical specifications are subject
spr65-006 to change without notice.
Operating Manual Version 1.7 – Status: 04/2020
Page 4 of 27 poc: SFi
Notes
This is a class A device according to EN55022.
For more information, please refer to Chapter 1.1 – Radio interference.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This Class A digital apparatus complies with Canadian ICES-003.
This manual is applicable for the following devices:
·Scape® Pro 65" (spr65-006 with st65-006 and pcsi-005)
Information in this document is subject to change without notice. ©2020 Interactive Scape GmbH. All rights reserved.
The document or excerpts from the document may not be duplicated without the prior permission of Interactive Scape
GmbH.
Interactive Scape GmbH shall not be liable for any errors contained in this document or any other incidental or
consequential damages resulting from the delivery, use or application of this material.
All product names mentioned in this document are trademarks or registered trademarks of their respective owners.

1. General
—
Scape® Pro Technical specifications are subject
spr65-006 to change without notice.
Operating Manual Version 1.7 – Status: 04/2020
Page 5 of 27 poc: SFi
1. General
This manual describes the safe installation, configuration and correct operation of the Scape® Pro.
If your device does not have an integrated PC, you can skip the chapters and notes about the integrated PC All other
notes and instructions continue to apply without restriction.
If necessary, pay attention to the supplementary documents, such as the installation instructions.
1.1. Safety instructions
Before using and operating your Scape® Pro, observe the following safety instructions to prevent you, your environment
or the Scape® Pro from being damaged.
Fire and electric shock
Overloaded sockets, extension cords and power strips can cause fire and electric shock.
· Avoid using power strips and extension cords if possible.
· Do not chain multiple extension cords or power strips together.
Overheating
Heat build-up can overheat the screen and the integrated PC. This can damage the device.
·Ensure there is sufficient air circulation around the Scape® Pro.
·Make sure all the ventilation holes on around the screen and integrated PC are uncovered.
Excess voltage from lightning strikes
In the event of a thunderstorm there is a risk of excess voltage damage from lightning strikes electrical appliances that
are plugged in.
·Do not install the Scape® Pro during a thunderstorm.
·Disconnect the devices from the mains during thunderstorms.
Moisture, liquid and steam
Moisture, liquid and steam inside the Scape® Pro can cause electric shocks or short circuits.
·Only use the Scape® Pro indoors.
·Do not allow liquids to get inside the Scape® Pro.
·Protect your Scape® Pro from steam and moisture.

1. General
—
Scape® Pro Technical specifications are subject
spr65-006 to change without notice.
Operating Manual Version 1.7 – Status: 04/2020
Page 6 of 27 poc: SFi
Improper cleaning
Improper cleaning with harsh detergents and solvents or soaking wet cloths can damage the Scape® Pro.
·Observe the information on cleaning your Scape® Pro (see Chapter 1.3 – Cleaning instructions).
Improper opening and repair
Improper opening and improper repairs may be dangerous to users of the device.
·Do not open the housing of the device.
·In case of repair contact the manufacturer or a specialist dealer.
Radio interference
Radio interference can be generated by any device that emits electromagnetic signals. Due to the large number of
devices that transmit and receive radio waves, interference from overlapping radio waves can occur.
·Do not use the Scape® Pro in locations where the use of radio equipment is prohibited.
·Always follow the instructions and instructions of authorized persons to switch off radio equipment, especially in
hospitals, outpatient health centers, medical practices and other medical facilities, to avoid interference with sensitive
medical equipment.
·Check with your doctor or the manufacturer of your medical device (pacemaker, hearing aid, implant with electronic
control, etc.) to see if it can work your Scape® Pro without interference.
·If necessary, maintain the minimum distance of 15 cm recommended by medical device manufacturers to avoid
interference with your medical device.
Hazardous environments
Under unfavorable conditions, radio waves near explosive atmospheres may lead to fire or explosions.
·Do not install and operate the Scape® Pro near explosive gases, flammable gases, areas where the air contains
chemicals or particles such as grain, dust or metal powders, and near detonation zones.
·In places with potentially explosive gases and near detonation zones, follow the instructions for switching off the
electronic devices to avoid disruption of the blasting and ignition systems.
Load and damage to the surface
Rough, hard or sharp-edged materials and heavy objects can damage the screen surface of the Scape® Pro.
·Do not place heavy objects on the screen.
·Use only objects with smooth or soft bottom surfaces on the screen.
·Clean the undersides of the objects before and after each use.

1. General
—
Scape® Pro Technical specifications are subject
spr65-006 to change without notice.
Operating Manual Version 1.7 – Status: 04/2020
Page 7 of 27 poc: SFi
1.2. Scope of delivery
The following accessories are included with your Scape® Pro:
·Power cable with powerCON plug for connection to the mains supply
·Network cable for connection to a local network
·Wireless keyboard with trackpad
·Screen cleaning kit
·Operating instructions (possibly by email)
1.3. Cleaning instructions
The touch sensor of the Scape® Pro does not usually need to be serviced. Nevertheless, it is recommended to clean the
glass surface of the screen regularly.
·Disconnect the device from the mains before cleaning.
·Typically, a solution of isopropyl alcohol and water (50:50 blend ratio) or the included screen cleaning kit are best for
cleaning the touch sensor.
·Apply the solution to a soft, lint-free cloth. Avoid using rough cloths.
·Use the cloth to clean the glass surface. Apply the liquid only to the cloth and never directly to the device. This will
prevent liquid from entering the inside of the device or causing marks on the frame.
To clean the Corian surfaces, a commercial plastic cleaner is recommended. Put it on a clean cloth and then treat the
surfaces with it.
1.4. Transportation instructions
The safest way to transport your device is in a Scape® Pro flight case (sold separately).
·The device is very heavy. Make sure that there are always at least two people to lift and carry the device.
·Do not transport the device upside down.
·Secure the device against slipping and tilting.

2. Specifications and set up
—
Scape® Pro Technical specifications are subject
spr65-006 to change without notice.
Operating Manual Version 1.7 – Status: 04/2020
Page 8 of 27 poc: SFi
2. Specifications and set up
2.1. Connections and controls
All connections for power and peripherals are located on the PC unit of the Scape® Pro.
This is located below the screen on the right-hand side of the device.
Loosen the two 2.5 mm hexagon socket screws on the lower cover on the inside of the PC unit to expose the
connections.
The cover plate is designed in such a way that there is sufficient space to reattach it after all cables have been
connected. After all the cables have been connected, reattach the plate to the PC unit to protect the connections and
prevent unintentional removal of the cables.
2.1.1. PC unit
1
On / Off switch
2
WLAN antenna connection (SMA) with WLAN antenna
USB 2.0 (
type A)
3
Cover plate for power and peripheral connections
1
2
3

2. Specifications and set up
—
Scape® Pro Technical specifications are subject
spr65-006 to change without notice.
Operating Manual Version 1.7 – Status: 04/2020
Page 9 of 27 poc: SFi
2.1.2. Connections for power and peripherals
4
USB 3.0 (type A)
5
USB 3.0 (type A)
6
HDMI 2.0
7
RJ45 network connection
8
powerCON TRUE1 Power supply
- input and output

2. Specificationsand set up
—
Scape® Pro Technical specifications are subject
spr65-006 to change without notice.
Operating Manual Version 1.7 – Status: 04/2020
Page 10 of 27 poc: SFi
2.1.3. Touch screen
The screen of the Scape® Pro comes preinstalled and connected to the integrated PC ready for operation.
*analogous to button on remote control
1
IR
-Sensor for remote control
2
Switch between Touch TUIO / USB Touch
3
RJ
-45 Lan interface – to use the
Touch & Object Assistant
4
USB-Connection Type B – for direct connection of touch and PC
5
DisplayPort input
6
HDMI 2.0 input (UHD 60 Hz)
7
HDMI
input
8
DVI input
9
Stand-by
*(17)
10
Status LED
11
Close OSD / > back / > show input selection
*(21)
12
Plus /
Right *(23)
13
Minus / Left
*(22)
14
Open OSD / confirm selection
*(20)
15
IEC socket for connection to 230V 50Hz
16
Main power switch
15
16