Interlogix AS272 Assembly instructions

© 2018 UTC Fire & Security Americas Corporation, Inc. 1 / 2 P/N 142945999-4 • REV G • ISS 15DEC18
AS272/AS273 Indoor Siren Installation Sheet
EN
EN: Installation Sheet
Description
AS272 is a two-tone self-supplied siren without flash, ideal for
use as an internal alarm sounder for residential and industrial
alarm applications.
AS273 is a two-tone self-supplied siren with a beacon, ideal for
use as an internal alarm sounder for residential and industrial
alarm applications.
Caution: Only use external current limited power supply. We
recommend 5 A supply.
Figure
(1) 3 mounting screws
(2) Siren cover closing screw
(3) 5 cable input options
Installation procedure
First, wire the control panel (power down) to the siren as
shown, before connecting the battery. When the battery is
connected for the first time, the siren will give a short beep
instead of a fully sounding alarm.
It is impossible to further activate the siren before the correct
jumper settings have been made and all input voltages (power
supply voltage and hold-off voltage) are correct.
In order to work properly, the siren needs to be provided with a
constantly present power supply to terminals 3 and 4.
The siren, the buzzer or the flashing light (AS273 only) will be
activated when the hold-off current at the input is removed.
The siren will also be activated if the external power supply is
decreased considerably.
If one of the siren inputs (siren or buzzer) is activated, the
other one will be blocked. Before the other input can be
activated, the input first activated should be switched off. This
does not apply to the flashing light input (AS273) that is
independent from both other inputs.
The time the siren will sound is fixed at maximum 20 minutes.
Connections
Number
Description
1, 2.
Tamper
3.
+12 V
4.
0 V
5.
Siren hold-off
6.
Buzzer hold-off
7.
Control flashlight (AS273 only)
WARNING: The beacon uses high voltage. To avoid personal
injury or death from electrocution, do not touch bare wires and
beacon electronics before the energy discharges.
AS273
1234567
J1 J2 J3
Battery
Battery optional
No.: BS170-N
AS272
123456
J1 J2
Battery optional
No.: BS170-N
Battery
Red
Black
(1)
(2) (2)
(1)
(1)
(1)
(3)
(3) (3)
WIRING INPUTWIRING INPUT
(1)
(1)
(3)
(3) (3)
BS170-N Red
Black BS170-N

2 / 2 P/N 142945999-4 • REV G • ISS 15DEC18
Jumpers
J1: Siren
J2: Buzzer
J3: Beacon (AS273 only)
Jumper settings
Position
Input level
0 V
12 V
Floating
1.
Input disabled
Input disabled
Input disabled
2.
Not active
Active
Active
3.
Active
Not active
Active
Specifications
Using without battery
Using with battery
Supply (limited
current)
10 to 14.2 V
max. 5 A
12.8 to 14.2 V
max. 5 A
Current consumption:
Siren/buzzer
active
Siren/buzzer +
beacon active
120 mA at 12 V(typical), 20 mA (idle)
230 mA at 12 V(typical)
Tamper output
80 mA, 30 V
Sound output:
Siren
Buzzer
101 dB at 1 m (typical)
100 dB at 1 m (typical)
Frequency:
Siren
Buzzer
2.2 to 2.8 kHz (typical)
2 kHz
Operating
temperature
−25 to +55°C
EN 50131:
−10 to +55°C
0 to +45°C
Relative humidity
EN 50131: 93% max.
Dimensions
155 × 114 × 44 mm
IP rating (with sealed
cable entry)
IP30 IK02
Recommender
battery
BS170-N: 9 V, 1700 mAh Lithium
Unchargeable
Beacon (AS273 only)
Light output
100 000 peak lumens
Flash frequency
1 Hz
Spike suppression
network
Standard fitted
IP rating (with sealed
cable entry)
IP30 IP02
Battery replacement or removal
Caution: Batteries can explode or cause burns
when incorrectly (dis)assembled or exposed to fire
or high temperatures.
Dispose of used battery according to battery directive
instructions and/or as required by local laws. Keep away from
children.
To replace batteries, disconnect the battery from the siren.
Only replace the battery with the recommended battery. Do not
use a different type of batteries. Use of any other batteries may
present a risk of fire or explosion.
Regulatory information
Manufacturer
PLACED ON THE MARKET BY:
UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092, USA
AUTHORIZED EU REPRESENTATIVE:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Product warnings
and disclaimers
THESE PRODUCTS ARE INTENDED FOR SALE
TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. UTC FIRE & SECURITY
CANNOT PROVIDE ANY ASSURANCE THAT
ANY PERSON OR ENTITY BUYING ITS
PRODUCTS, INCLUDING ANY “AUTHORIZED
DEALER” OR “AUTHORIZED RESELLER”, IS
PROPERLY TRAINED OR EXPERIENCED TO
CORRECTLY INSTALL FIRE AND SECURITY
RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
https://firesecurityproducts.com/policy/product-
warning/ or scan the QR code.
Certification
EN 50131-4, Security Grade 2, Environmental
class II (Pry-off tamper is not certified for an
EN 50131 Security Grade 2 applications.)
Tested and certified by Applica Test &
Certification.
AS272 and AS273 are certified for EN 50131-4
only if used without a battery.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.utcfssecurityproducts.eu/recycle/
This product may contain a battery that cannot be
disposed of as unsorted municipal waste in the
European Union. See the product documentation
for specific battery information. The battery is
marked with this symbol, which may include
lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling return the
battery to your supplier or to a designated
collection point. For more information see
www.utcfssecurityproducts.eu/recycle/
Contact information
www.utcfireandsecurity.com or www.interlogix.com.
For customer support, see www.utcfssecurityproducts.eu