Interlogix ATSx500A Series Assembly instructions

Advisor Advanced
ATSx500A(-IP) Installation
and Programming Manual
P/N 466-2576 (EN) • REV B • ISS 16SEP16

Copyright
© 16SEP16 UTC Fire & Security Americas Corporation, Inc. All
rights reserved.
Trademarks and
patents
Interlogix, Advisor Advanced ATSx500A(-IP) name and logo are
trademarks of UTC Fire & Security.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacturer
UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Version
This document applies to the following Advisor Advanced firmware
versions:
ATSx500A(-IP): MR_3.0
Certification
EN 50131-1 System requirements
EN 50131-3 Control and indicating equipment
EN 50131-6 Power Supplies
EN 50136-1-1 Alarm systems -Alarm Transmission systems
ATS1500A(-IP): Security Grade 2, Environmental class II
ATS3500A(-IP): Security Grade 3, Environmental class II
ATS4500A-IP: Security Grade 3, Environmental class II
Note: ATS1500A(-IP) is upgradable to Security Grade 3 using the
ATS-MM-TK (MM enclosure) or the ATS-SM-TK (SM enclosure)
tamper kit.
Tested and certified by VdS Schadenverhütung GmbH
Important: To comply with the above standards, it is required to
configure the system according to settings listed in Chapter 8
“Regulations” on page 301 onwards.
This product has not been designed to comply with EN 50134 and
EN 54 norms.
European Union
directives
UTC Fire & Security hereby declares that this device is in
compliance with the applicable requirements and provisions of one
or more of the Directives 2014/30/EU and 2014/35/EU. For more
information see www.utcfireandsecurity.com or www.interlogix.com.
2002/96/EC (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.utcfssecurityproducts.eu/recycle/
Contact information
www.utcfireandsecurity.com or www.interlogix.com
Customer support
www.utcfssecurityproducts.eu

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual i
Content
Important information iii
Chapter 1 Quick installation and programming 1
Quick installation 2
Quick programming 4
Chapter 2 Installation 7
General installation information 8
Maintenance 16
Mounting 18
Earthing 20
Shielding 21
Cabling 22
Configuration 30
Specifications 35
Chapter 3 System functions 41
Function list 43
Zones 45
Areas 50
Set and unset 51
Inhibit and isolate 53
Keys 54
Bus devices 58
Users 60
User groups 62
PIN 66
Outputs 67
Access control 68
Condition filters 74
Triggers 76
Calendar 77
Events 79
Tests and diagnostics 80
Alarm reporting 84
User programmable functions 88
Autoset 91
Wireless device programming 92
Using cameras 98
Engineer reset 102
Timed unset / ATM 103
Chapter 4 Programming 105
The Advisor Advanced menu 106

ii Advisor Advanced ATSx500A(-IP) Installation and Programming Manual
How to program the options 108
Remote access 113
Initial start-up 114
Chapter 5 Menu reference 117
1 Service menu 120
2 Device menu 142
3 User menu 162
4 Zones and areas 171
5 Door menu 196
6 Outputs and filters 217
7 Calendar 225
8 System option menu 232
9 Dialler menu 258
Chapter 6 Software 287
Programming Advisor Advanced via configuration software 288
Upgrading Advisor Advanced firmware 290
Chapter 7 Troubleshooting 295
Recovery procedure 296
Device troubleshooting 297
Chapter 8 Regulations 301
Options affected by EN 50131 regulations 302
Options affected by other regulations 308
Appendix A Advisor Advanced events 311
Appendix B Advisor Advanced reporting codes 327
Glossary 337
Index 343
Programming map 351

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual iii
Important information
This document includes an overview of the product and detailed instructions
explaining how to install your Advisor Advanced system and program it.
To use this document effectively, you should have the following minimum
qualifications:
• Basic knowledge of alarm systems and components
• Basic knowledge of electrical wiring and low-voltage electrical connections
Read these instructions and all ancillary documentation entirely before installing
or operating this product.
Important note
This manual provides information for all Advisor Advanced and Advisor
Advanced-IP control panels in all variations. “Advisor Advanced control panel”
refers to any variant of the Advisor Advanced control panels, unless specifically
stated otherwise.
List of panel variants
Table 1: List of ATSx500A(-IP) panel variants
Model
Enclosure
Dimensions (mm)
Weight (kg)
ATS1500A-MM
Metal
MM, 315 x 388 x 85
5.2
ATS1500A-IP-MM
Metal
MM, 315 x 388 x 85
5.2
ATS1500A-SM
Metal
SM, 250 x 250 x 86
2.8
ATS1500A-IP-SM
Metal
SM, 250 x 250 x 86
2.8
ATS1500A-LP
Plastic
LP, 257 x 400 x 112
2.6
ATS1500A-IP-LP
Plastic
LP, 257 x 400 x 112
2.6
ATS3500A-MM
Metal
MM, 315 x 388 x 85
5.2
ATS3500A-IP-MM
Metal
MM, 315 x 388 x 85
5.2
ATS3500A-LP
Plastic
LP, 257 x 400 x 112
2.6
ATS3500A-IP-LP
Plastic
LP, 257 x 400 x 112
2.6
ATS4500A-IP-MM
Metal
MM+, 315 x 445 x 88
5.4
ATS4500A-IP-LM
Metal
LM, 475 x 460 x 160
10.9
Notes
• Not all variants may be available.
• Weight does not include batteries.

iv Advisor Advanced ATSx500A(-IP) Installation and Programming Manual
Limitation of liability
To the maximum extent permitted by applicable law, in no event will UTCFS be
liable for any lost profits or business opportunities, loss of use, business
interruption, loss of data, or any other indirect, special, incidental, or
consequential damages under any theory of liability, whether based in contract,
tort, negligence, product liability, or otherwise. Because some jurisdictions do not
allow the exclusion or limitation of liability for consequential or incidental
damages the preceding limitation may not apply to you. In any event the total
liability of UTCFS shall not exceed the purchase price of the product. The
foregoing limitation will apply to the maximum extent permitted by applicable law,
regardless of whether UTCFS has been advised of the possibility of such
damages and regardless of whether any remedy fails of its essential purpose.
Installation in accordance with this manual, applicable codes, and the instructions
of the authority having jurisdiction is mandatory.
While every precaution has been taken during the preparation of this manual to
ensure the accuracy of its contents, UTCFS assumes no responsibility for errors
or omissions.
Advisory messages
Advisory messages alert you to conditions or practices that can cause unwanted
results. The advisory messages used in this document are shown and described
below.
WARNING: Warning messages advise you of hazards that could result in injury
or loss of life. They tell you which actions to take or to avoid in order to prevent
the injury or loss of life.
Caution: Caution messages advise you of possible equipment damage. They tell
you which actions to take or to avoid in order to prevent the damage.
Note: Note messages advise you of the possible loss of time or effort. They
describe how to avoid the loss. Notes are also used to point out important
information that you should read.
Safety sign identifies actions or practices that are required by
EN 60950 Safety Standard.

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual 1
Chapter 1
Quick installation and
programming
Summary
The chapter contains basic steps of connection and programming of the Advisor Advanced
control panel and auxiliary devices.
For more detailed description of the installation process, see Chapter 2 “Installation” on page 7.
For details on programming, see Chapter 4 “Programming” on page 105 and Chapter 5 “Menu
reference” on page 117.
Content
Quick installation 2
Quick programming 4

Chapter 1: Quick installation and programming
2 Advisor Advanced ATSx500A(-IP) Installation and Programming Manual
Quick installation
RxTx
SYS
POLL
MI/PANEL
ETHERNET
SIM
GSM
GPRS/3G
DGP Addr
1 2 3 4
SIM
USB
RxTx
USB
MI
IP
CON12
CON13
T1
T2
S4 S5
+ +
S1 C
+
S2 CT C
+ +
- - 1 C 2 3 C 4 5 C 6 7 C 8
~~+-
AC BATT LC-OUTPUTS HC-OUTPUTS SIR TMP AUX POWER INPUTS
EARTH
CTD-
D+
0V
+12V COMMS TAMPER
+
S3 C
CON16
NTC
ATS7700
ATS608ATS624
ATS626
1K
4K7
4K7 4K7 4K7 4K7 4K7 4K7
+12V
Zone
GND
4K74K7
Zone
GND
DC101
DD1012AM
+ -
TDA74xxNG
1K 1K
2
2
Off
On
Isolated fault
contact
3 resistor single
zone
(Terminal 3-10)
=
=
J1
J1
JF JT JA
2 2K
3K
4 7K
1K
2 2K
4 7K 5 6K
1K
2 2K
4 7K 5 6K
1
2
3
4
1
2
1
2
1
2
3
4
5
6
1
2
1
2
SW1 - Generic settings
LED ON
Remote OFF
Auto Rem. Test ON
Positive Polarity
LED OFF
Remote ON
Negative Polarity
Range
SW2 - AM/Fault settings
Mask to alarm and
fault relay
Auto reset
Advanced AM sens.
AM Day mode only
Mask to fault relay
only
Authorized reset
Standard AM sens.
AM Day and Night
4
1 .
m
( 3 ft )
12
40 .
m
( ft )
9
30 .
m
( ft )
6
20 .
m
( ft )
Auto Rem. Test OFF
10K
Zone
J1
1
Alarm
GND
+12V
Fault
Alarm
Fault
1 3 4 5
2 6 78 9

Chapter 1: Quick installation and programming
Advisor Advanced ATSx500A(-IP) Installation and Programming Manual 3
D+0V+12V D- IN OUT
Rx
Tx
EARTH
CTD-
D+
0V
+12V COMMS TAMPER
D+0V+12V D- IN OUT
0
123
45 6
7 8 9
12
abc
jkl
tuv
def
ghi
.,’?!
*
#
A B C
Address 1
RxTx
SYS
POLL
MI/PANEL
ETHERNET
SIM
GSM
GPRS/3G
DGP Addr
1 2 3 4
SIM
USB
1
1
ATS1135 ATS1135
TDA74xxNG
0
123
45 6
7 8 9
12
abc
jkl
tuv
def
ghi
.,’?!
*
#
A B C
Address 2
2

Chapter 1: Quick installation and programming
4 Advisor Advanced ATSx500A(-IP) Installation and Programming Manual
Quick programming
Initial start-up
Note: See “The Advisor Advanced menu”
on page 106 for menu explanation. For
more information on editing options, see
“How to program the options” on page 108.
Switch the panel on. The further messages
and menus are listed in the table below.
Display
Instructions
INFO
Inst required
Press Enter to continue.
1>Panel language
Choose English.
2>Defaults
Choose EN 50131 Grade 3.
4>PIN length
Enter 6.
5>Time&date
Set current time and date.
6 Install
>Cancel<
Choose OK
Installer
PIN:127800
Press Enter to continue.
Supervisor
PIN:112200
Press Enter to continue.
The panel restarts.
Auto configuration
Auto Config?
>Yes<
Press Enter to continue.
Rkp 1-16 BUS1
R-?-------------
Exp 1-15 BUS1
-?-------------
Wait until the panel
configures all bus devices
and zones.
Added
R:1 D:0 Z:8
Press Enter to continue.
Enabling service in
UTC F&S
THU 05 Mar 12:21
Press 112200, Menu
1>Zone options
2 Isolate
Go to menu 8.8 Service in
8>Service in
Enable?
Enable Installer in time
Press Cancel, Cancel to log off.
Programming menu entry
UTC F&S
THU 05 Mar 12:21
Press 127800, Menu
Inh reports
>No<
Press Enter to continue.
Inh tampers
Unset areas
1>Service menu
2 Device menu
The installer menu is displayed.
Changing installer PIN
Go to 3.1.n.2.1 Change PIN (see page 163).
1>Change PIN
***********
Press Enter.
New PIN
>_
Enter the new installer PIN.
Configuring zones
Go to 4.1 Zone menu (see page 171).
4>Zones&Areas
Press Enter.
1>Zone menu
Press Enter.
0>Add zone
1 Zone 1
Select a zone.
For each zone used in the system, enter
zone name in 4.1.n.1 Zone name (page
172).
01 Zone name
>1 Zone 1 <
Next, set its zone type in 4.1.n.2 Zone type
(see page 172).