Interlogix RF-7220-07-1 Assembly instructions

© 2017 UTC Fire & Security Americas Corporation, Inc. 1 / 3 P/N 466-2912 • REV A • ISS 05JAN17
RF-7220-07-1 Wireless Outdoor Siren
Installation Sheet
EN
1
2
J3
78910123456
5
6
7
8
9
10
11
12
2
3
1

2 / 3 P/N 466-2912 • REV A • ISS 05JAN17
3
4
EN: Installation Sheet
Wiring diagram
Figure 2 legend
(1) Siren PCB
(2) Speaker
(3) Beacon
(4) 4X lithium battery pack (not included)
(5) IO module power cable (black)
(6) Tamper
(7) Tamper
(8) Beacon + (red)
(9) Beacon- (black)
(10) Siren driver + (red)
(11) Siren driver −(black)
(12) IO module PCB
Learning-in an outdoor siren
You have to learn-in the siren before mounting it to the desired
position. In order to add a wireless siren to the system perform
the following steps:
1. Enter the programming mode on the panel
2. Enter your username and password and then click Sign In.
3. Click Settings.
4. Click Zones.
5. The outdoor siren will occupy maximum 4 zone numbers.
Click “Select Zone to Configure” to set the first zone
number of the outdoor siren.
6. Click Learn.
7. Power up the outdoor siren with the tamper switch open.
8. Wait for module LEDs to blink on, then off.
9. Close tamper switch for 2 seconds, then reopen within 5
seconds.
10. The screen will indicate the outdoor siren has been
learnt-in and a serial number will appear. Read the pop up
messages.
11. Select Outdoor Siren as the application.
12. Click Save when done.
Mounting the siren
For mounting instructions, see Figure 3. Pay attention to the
precise placement of the tamper switch against the wall. To
comply with an EN50131-4 grade 2 installation, please take
special care of positioning the tamper switch lever to the wall,
and insert a screw in the wall opposite to the tamper switch
lever. This screw has to be adjusted in height in order to press
adequately on the tamper switch lever so that the microswitch
is in a “closed” position and resting on the screw’s head
instead of the wall (see Figure 4, position 1). The siren needs
to signal a tamper alarm when the unit is taken more than
5 mm from its mounting surface (see Figure 4).
Siren configuration
To allow the IO module to control the output on the outdoor
siren, you need to cut jumper 3 and then optionally 1 and/or 2.
Jumper 3 is a start-up protection. Jumpers 1 and 2 are
responsible for timer settings, and you can cut one of them or
both, according to the table below.

P/N 466-2912 • REV A • ISS 05JAN17 3 / 3
Timer setting
Time J1 J2
3 minutes (ex-factory)
5 minutes
10 minutes
20 minutes
Safety instructions
WARNING: Do not open the flash housing. Risk of high
voltage.
Battery replacement and removal
Caution: Batteries can explode or cause burns when
recharged, incorrectly (dis)assembled, or exposed to fire or
high temperatures.
Dispose of used battery according to battery directive
instructions and/or as required by local laws. Keep away from
children.
To remove the batteries from the outdoor siren, please pull the
black plastic strap that holds the battery pack. Only replace the
batteries with the standard lithium battery pack BS7201-N. Do
not use a different type of lithium batteries.
Note: The lithium battery pack BS7201-N is not included with
the siren, and must be purchased separately.
Specifications
Power supply specifications
Number and type of
batteries
BS7201-N, 4-cell custom battery pack,
lithium (purchased separately)
Battery capacity 12.5 Ah
Electronics, board
operating voltage
3.0 VDC
Siren/flash light part
operating voltage
12.0 VDC
Battery lifetime (typical) 3 years *
Current consumption –
IO module (typical)
140 µA at 3.0 VDC ± 10%
Current consumption –
siren (typical)
340 mA at 12.0 VDC ± 10%
Current consumption –
beacon (typical)
74 mA at 12.0 VDC ± 10%
Environmental
Operating temperature −25°C to +50°C
Humidity max 95%, non condensing
Shipping weight 2.3 kg
Enclosure dimensions 310 x 222 x 91 mm
EN 50131 grade and
class
Security Grade 2, Environmental
Class III
* Assumption: maximum 20 siren activations of 3 minutes and
beacon activations of 15 minutes per year.
Regulatory information
Manufacturer UTC Fire & Security Americas Corporation, Inc.
1275 Red Fox Rd., Arden Hills, MN 55112-6943,
USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
EU compliance
Certification EN 50131-5-3:2005
EN 50131-5-3/A1:2008
EN 50131-4:2009
Tested and certified by Telefication B.V.
2012/19/EU (WEEE directive): Products marked with
this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For
more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains
a battery that cannot be disposed of as unsorted
municipal waste in the European Union. See the
product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg). For proper
recycling, return the battery to your supplier or to a
designated collection point. For more information
see: www.recyclethis.info.
UTC Fire & Security hereby declares that this device
is in compliance with the applicable requirements
and provisions of one or more of the Directives
1999/5/EC, 2014/30/EU and 2014/35/EU. For more
information see: www.utcfireandsecurity.com.
Contact information
www.utcfireandsecurity.com or www.interlogix.com
Customer support
For customer support, see www.utcfssecurityproducts.eu