Intex Krystal Clear 638R User manual

106A
(106) MODEL 638R FILTER PUMP ENGLIS 7.5” X 10.3” PANTONE 295U 06/23/2011
English
OOWWEERR’’SS MMAAUUAALL
IMPORTA T
SAFETY RULES
Read, understand, and follow all
instructions carefully before
installing and using this product.
Don’t forget to try these other fine Intex products: pools, pool accessories,
inflatable pools and in-home toys, airbeds and boats available at fine
retailers or visit our website.
For illustrative purposes only.
©2011 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd.
- Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle
Rechte vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous
licence de/Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen
Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Trading Ltd., Intex Development Co. Ltd., G.P.O
Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801 • Distributed in the European
Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea por/Vertrieb in der Europäischen Union
durch/Intex Trading B.V., P.O. Box nr. 1075 – 4700 BB Roosendaal – The Netherlands
Krystal Clear™
Model 638R Filter Pump
220 - 240 V~, 50 Hz, 99 W
Hmax 1.0 m, H min 0.19 m, IPX5/IPX7
Max. Water Temperature 35 °C
106-*A*-R0-1206

106A
SAVE THESE INSTRUCTIONS Page 2
(106) MODEL 638R FILTER PUMP ENGLIS 7.5” X 10.3” PANTONE 295U 06/23/2011
English
TTAABBLLEE OOFF CCOOTTEETTSS
Warnings.......................................................................... 3
Parts List & Reference.................................................... 4-5
Setup Instructions .......................................................... 6-8
Maintenance..................................................................... 9-10
Pool Care and Chemicals............................................... 9
Long Term Storage.......................................................... 10
Troubleshooting Guide................................................... 11
Common Pool Problems................................................. 12
General Aquatic Safety................................................... 13
Limited Warranty............................................................. 14
Intex Service Center Locations...................................... 15

106A
SAVE THESE INSTRUCTIONS Page 3
(106) MODEL 638R FILTER PUMP ENGLIS 7.5” X 10.3” PANTONE 295U 06/23/2011
English
SSAAFFEETTYY RRUULLEESS
WARNING
IMPORTA T SAFETY RULES
Read, Understand and Follo All Instructions Carefully Before Installing and Using this Product.
READ AND FOLLOW ALL INSTRUCTIONS
These product warnings, instructions and safety rules provided with the product represent
some common risks of water recreation devices and do not cover all instances of risk and
danger. Please use common sense and good judgement when enjoying any water activity.
• To reduce the risk of injury, do not permit children to use this product. Always
supervise children and those with disabilities.
• Children must stay away from this product and electrical cord(s).
• Children should be supervised to ensure that they do not play with the appliance.
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge. They
must at all times be supervised by a knowledgeable and experienced adult
responsible for their safety.
• Assembly and disassembly by adults only.
• Risk of electric shock. Connect this product only to a grounding type receptacle
protected by a ground-fault circuit interrupter (GFCI) or residual current device
(RCD). Contact a qualified electrician if you cannot verify that the receptacle is
protected by a GFCI/RCD. Use a qualified electrician to install the GFCI/RCD,
which has a maximum rate of 30mA. Do not use a portable residual current device
(PRCD).
• Always unplug this product from the electrical outlet before removing, cleaning,
servicing or making any adjustment to the product.
• The plug must be accessible after produc t is installed.
• Do not bury the electrical cord. Locate the cord where it will not be damaged by
lawn mowers, hedge trimmers and other equipment.
• The supply cord cannot be replaced. If the cord is damaged the appliance should
be scrapped.
• To reduce the risk of electric shock, do not use extension cords, timers, plug
adaptors or converter plugs to connect unit to electric supply; provide a properly
located outlet.
• Do not attempt to plug in or unplug this product while standing in water or when
your hands are wet.
• Keep this product more than 2m away from the pool. (for France only).
• Keep the plug of this product more than 3.5m away from the pool.
• Position this product away from the pool, so as to prevent children from climbing on
it and accessing the pool.
• Do not operate this product when pool is occupied.
• This product is for use with storable pools only. Do not use with permanently
installed pools. A storable pool is constructed so that it may be readily
disassembled for storage and reassembled to its original configuration.
• This product is intended to be used only for the purposes described in the manual!
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN
PROPERTY DAMAGE, ELECTRIC SHOCK, ENTANGLEMENT OR
OTHER SERIOUS IN URY OR DEATH.

106A
SAVE THESE INSTRUCTIONS Page 4
(106) MODEL 638R FILTER PUMP ENGLIS 7.5” X 10.3” PANTONE 295U 06/23/2011
English
PPAARRTTSS LLIISSTT
PARTS LIST
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
123
6
5
4
78
10 11
9

106A
SAVE THESE INSTRUCTIONS Page 5
(106) MODEL 638R FILTER PUMP ENGLIS 7.5” X 10.3” PANTONE 295U 06/23/2011
English
PPAARRTTSS RREEFFEERREECCEE
PARTS REFERE CE
Before assembling your product, please take a fe minutes to check the contents
and become familiar ith all the parts.
When ordering parts, be sure to quote the model number and part numbers.
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
678 9
9
1
2
3
4
5
11
10
1
2
3
4
5
6
7
8
9
10
11
REF. NO. DESCRIPTION QTY. SPARE PART NO.
1
1
1
1
1
2
4
2
2
1
1
10460
10264
10459
10325
10134
10122
10399
11070
11071
11072
AIR RELEASE VALVE
VALVE O-RING
T READED COVER
COVER SEAL
FILTER CARTRIDGE (59900)
OSE SEAL
OSE CLAMP
OSE
STRAINER CONNECTOR
POOL INLET NOZZLE
STRAINER GRID

106A
SAVE THESE INSTRUCTIONS Page 6
(106) MODEL 638R FILTER PUMP ENGLIS 7.5” X 10.3” PANTONE 295U 06/23/2011
English
SSEETTUUPP IISSTTRRUUCCTTIIOOSS
SETUP I STRUCTIO S
Be sure you have access to water to fill the pool and chemicals for the water. A
small coin can be used to tighten the hose clamps (7).
IMPORTANT: This filter pump is shipped with the air release valve (1) open
(open the air release valve if necessary). DO NOT replace the air release valve
until you reach STEP #8. Failure to follow these instructions will result in air
trapped inside filter housing; the motor will run dry, be noisy and malfunction.
1. Assemble above-ground-pool first. Carefully follow the pool’s installation
instructions.
2. Place the filter pump the length of the hose away from the pool wall where the
lower black protruding hose connection is "sticking-out".
3. Insert the nozzle union (9 & 10) into the upper protruding hose connections.
Then insert the strainer union (9 & 11) into the lower protruding hose
connections. The hoses (8) fit over the strainers inserted into the connections.
4. There are two hoses to be connected to the filter pump hose connections. With
hose clamps (7), fasten one of the hoses (8) to the lower protruding hose
connection (marked "+" on the pool liner) and to the upper pump connection
(marked "+").
5. Connect the second hose to the remaining upper protruding hose connection
and to the lower pump connection. Make sure all the hose clamps (7) are tight.
6. Twist the filter pump’s threaded cover (3) in a clockwise direction to be sure it
is on "tight". Use only your hands to tighten the top. Do not tighten with tools
such as pliers.
7. Fill the pool to a level of at least 1-2 inches above the top connection. The water
will automatically flow down into the pump.
8. When water starts flowing out of the air release valve hole, screw in the air
release valve back into the filter housing cover. Do not over tighten the valve.
NOTE: Venting the system is necessary for air to escape as the filter
housing fills with water.
9. Connect the filter pump to the power outlet. The filter pump is now filtering the
water.
10. Operate the filter pump until the desired water clarity is obtained.
WARNING
Risk of electric shock. Connect this product only to a grounding type
receptacle protected by a ground-fault circuit interrupter (GFCI) or
residual current device (RCD). Contact a qualified electrician if you cannot
verify that the receptacle is protected by a GFCI/RCD. Use a qualified
electrician to install the GFCI/RCD, which has a maximum rate of 30mA.
Do not use a portable residual current device (PRCD).

106A
SAVE THESE INSTRUCTIONS Page 7
(106) MODEL 638R FILTER PUMP ENGLIS 7.5” X 10.3” PANTONE 295U 06/23/2011
English
SSEETTUUPP IISSTTRRUUCCTTIIOOSS
SETUP I STRUCTIO S (continued)
WARNING
Position this product away from the pool, so as to prevent children from
climbing on it and accessing the pool.
To inspect and change the filter cartridge, disconnect line cord, unscrew the pool
inlet nozzle (10) and strainer grid (11) from the strainer connectors and insert the
hat-like plugs into the strainer connectors before servicing the filter. After service,
open the air release valve, remove the plugs, allow any air to escape through the
valve before tightening the valve again and replace the pool inlet nozzle (10) and
strainer grid (11). The pump is now primed with water again and may be turned on.
(ILLUSTRATION NOT TO SCALE)
WATER LEVEL
POOL INLET
NOZZLE
(REMOVE)
HOSE CLAMP
INSIDE OF POOL
STRAINER GRID
(REMOVE)
PLUG
UPPER PROTRUDING
HOSE CONNECTION
W
A
T
E
R
D
I
R
E
C
T
I
O
N
W
A
T
E
R
D
I
R
E
C
T
I
O
N
UPPER PUMP
CONNECTION
LOWER PUMP
CONNECTION
THREADED
COVER
FILTER
CARTRIDGE
INSIDE
AIR RELEASE
VALVE
HOSE
The installation instruction shall provide information on requirements specified for
the electrical installation and shall include reference to national wiring rules.

106A
SAVE THESE INSTRUCTIONS Page 8
(106) MODEL 638R FILTER PUMP ENGLIS 7.5” X 10.3” PANTONE 295U 06/23/2011
English
SSEETTUUPP IISSTTRRUUCCTTIIOOSS
FILTER PUMP STATIO ARY MOU TI G OPTIO
-- (3) x M6 HEXAGON HEAD BOLTS
-- (3) x M6 HEXAGON LOCK-NUTS
145mm
145mm
145mm
145mm
145mm
145mm
There are three mounting holes located at the bottom of the filterpump base. These
holes are provided because various country’s regulations, especially in the
European community, require the filterpump to be secured to the ground or to a
base in a permanent upright position.
These three holes form a triangle pattern and are 145mm from each other. The
holes are slotted with a 7mm width.
The filterpump can be mounted on a cement base or onto a wooden structure to
prevent accidental falling over. Total assembly must exceed 18kg. The drawings on
the following show two possible ways of upright mounting.

106A
SAVE THESE INSTRUCTIONS Page 9
(106) MODEL 638R FILTER PUMP ENGLIS 7.5” X 10.3” PANTONE 295U 06/23/2011
English
MMAAIITTEEAACCEE
CAUTION
Concentrated chlorine solutions may damage the pool liner. Always
follow the chemical manufacturer’s directions, and the health and hazard
warnings.
POOL CARE A D CHEMICALS
• All pools require care to keep the water clear and hygienically clean. With
proper chemical control, your filter will help attain this objective. Consult your
pool supply dealer for instructions regarding the proper use of chlorine,
algaecide and other chemical agents required for sparkling clear water.
• Keep pool chemicals away from children.
• Do not replenish chemicals in pool while pool is occupied. Skin or eye irritations
could occur.
• Daily p checking and chemical treatment of the water is very important and
can not be overemphasized. Chlorine, algaecide and maintenance of proper p
levels are required when filling the pool as well as during the season. Consult
your local swimming pool supply store for instructions.
• The season's first filling of the pool may have brackish water requiring extra
water additives and extra filter changes. Do not allow swimming in pool until the
p level is balanced. Consult your local swimming pool supply store for
instructions.
• Keep spare filter cartridges on hand. Replace cartridges every two weeks.
• Chlorinated water may damage lawns, gardens or shrubbery as children play
in the pool and splash water outside the pool. Lawn areas underneath the
pool liner will be destroyed. Note that some types of grass may grow through
the liner.
• Filter run time depends on pool size, weather and usage level. Experiment with
various run times so as to produce clean clear water.

106A
SAVE THESE INSTRUCTIONS Page 10
(106) MODEL 638R FILTER PUMP ENGLIS 7.5” X 10.3” PANTONE 295U 06/23/2011
English
MMAAIITTEEAACCEE
1. Before emptying your pool for long term storage, or relocation, be sure the
water is directed towards an acceptable drain water receptacle away from the
house. Check local regulations for specific directions regarding disposal of
swimming pool water.
2. Now, drain the pool.
3. When the pool is empty, disconnect all pool hoses (8) from the pool and filter
pump, simply reverse the set up instructions.
4. Remove the filter cartridge as shown in the Filter Cartridge Cleaning section,
steps 2 thru 4.
5. Remove the nozzle and strainer unions from the pool wall. Place the wall
plugs into the hose connections. Loosen clamps (7) securing the strainer
connectors (9) before removal.
6. Drain water from the filter pump housing.
7. Leave filter pump pieces and hoses outside to thoroughly air dry.
8. Depending on the cartridge (5) usage, a new cartridge may be needed for next
season, keep a spare available.
9. Cover the seal (4), air release valve O-ring (2) and hose seals (6) with
petroleum jelly to preserve its resilience during storage.
10. Store the unit and accessories in a dry place. The storage's temperature should
be controlled, between 32 degrees Fahrenheit (0 degrees Celsius) and 104
degrees Fahrenheit (40 degrees Celsius) storage location.
11. The original packing can be used for storage.
LO G TERM STORAGE
It is recommended that the filter cartridge be replaced at least
every 2 weeks.
1. Make sure filter pump is not operating. Disconnect line cord.
2. To prevent water from escaping the pool, unscrew the pool inlet nozzle (10)
and strainer grid (11) from the strainer connectors and insert the hat-like plugs
into the strainer connectors.
3. In a counter-clockwise motion, remove threaded cover (3) and cover seal (4).
Be careful not to lose the cover seal (4).
4. Remove filter cartridge (5) to clean it. The filter may be cleaned from the spray
from a water hose.
5. Use judgement as to whether cartridge needs to be replaced.
6. Return cartridge to filtering position.
7. Return the seal (4) and threaded cover (3) to their original positions. Tighten
the threaded cover (3) by hand only, twisting it in a clockwise direction.
8. After service, open the air release valve, remove the plugs, allow any air to
escape through the valve before tightening the valve again and replace the
pool inlet nozzle (10) and strainer grid (11). The pump is now primed with water
again and may be turned on.
CLEA I G OR REPLACI G FILTER CARTRIDGES

106A
SAVE THESE INSTRUCTIONS Page 11
(106) MODEL 638R FILTER PUMP ENGLIS 7.5” X 10.3” PANTONE 295U 06/23/2011
English
TROUBLESHOOTI G GUIDE
TTRROOUUBBLLEESSHHOOOOTTIIGG GGUUIIDDEE
FILTER MOTOR
FAILS TO START
FILTER DOESN’T
CLEAN POOL
FILTER DOESN’T
PUMP WATER OR
FLOW IS VERY
SLOW
PUMP DOESN’T
WORK
TOP COVER
LEAKING
OSE LEAKING
AIR LOCK
• The motor is not plugged in.
• The fuse box needs checking.
• The GFCI/RCD circuit breaker
is tripped.
• Motor too hot and overload
protection shut motor off.
• Improper chlorine or p
levels.
• Filter cartridge is dirty.
• Damaged cartridge.
• Excessively dirty pool.
• The strainer screen is
restricting the water flow.
• Clogged inlet or discharge.
• An air leak on the intake line.
• Scale or buildup on cartridge.
• Excessively dirty pool.
• Dirty filter cartridge.
• The nozzle and strainer
connection are reversed.
• Low water level.
• Strainer screen plugged up.
• An air leak on the intake hose.
• Faulty motor or the impeller
is jammed.
• An air lock inside the
cartridge chamber.
• O-ring missing.
• Cover is not tight.
• Filter cartridge is dirty.
• ose clamps are not
well-fitted.
• There’s air trapped in the
pump housing and inlet hose.
TROUBLE CAUSE SOLUTION
• Filter cord must be plugged into a 3 wire
outlet that is protected by a Class A
Ground Fault Circuit Interrupter, or RCD.
• Reset circuit breaker. If circuit breaker
trips repeatedly, your electrical system
may have a defect. Turn off circuit
breaker and call an electrician to
correct the problem.
• Let motor cool down.
•
Adjust the chlorine and p level. Consult
your local swimming pool supply stores.
• Clean or replace cartridge.
• Check the cartridge for holes. Replace
if damaged.
• Operate the filter for longer periods.
• Clean the strainer screen at the inlet.
• Clear any obstructions in the intake
hose by discharging it inside pool wall.
• Tighten hose clamps, check hoses for
damage, check pool water level.
• Replace cartridge.
• Clean cartridge more often.
• Install the nozzle at the upper position
of the pool inlet, and the strainer at the
lower position of the pool outlet.
• Fill pool to correct water level.
• Clean strainer screens at pool inlet.
• Tighten hose clamps, check hose for
damage.
• Clear any sticks or leaves in the
intake hose.
• Open the release valve at top of pump.
• Remove cover & check for O-ring.
• Tighten cover (Manually).
• Replace or clean cartridge.
• Tighten or change hose clamps.
• Open air release valve, lift and lower
the inlet hose until water starts to flow
out of the air release valve, close air
release valve.
• The white inserts at both ends of the hoses shall remain inside and
shall be firmly inserted in the hose. Do not remove the white inserts
from the hoses. These white inserts are not serviceable parts.
• To facilitate the connection of the hoses into the black protruding hose
connectors on the pool wall, you may use soapy water solution (mix 6
drops of dish detergent in 1/2 a cup of water) to lubricate the inserts
by simply dipping the hose ends into the solution. Continue per
owner’s manual.
• Do not use lubricants such as machine or industrial oil or grease.
OSE
INSERT

106A
SAVE THESE INSTRUCTIONS Page 12
(106) MODEL 638R FILTER PUMP ENGLIS 7.5” X 10.3” PANTONE 295U 06/23/2011
English
COMMO POOL PROBLEMS
CCOOMMMMOO PPRROOBBLLEEMMSS
PROBLEM DESCRIPTION CAUSE SOLUTION
ALGAE
COLORED
WATER
SUSPENDED
MATTER IN
WATER
C RONIC
LOW WATER
LEVEL
SEDIMENT
ON POOL
BOTTOM
SURFACE
DEBRIS
• Chlorine and p levels
need adjustment.
• Copper, iron or
manganese in water
being oxidized by the
added chlorine.
This is Common.
• " ard water" caused
by a too high p level.
• Chlorine content is low.
• Foreign matter in
water.
• Rip or hole in pool
liner or hoses.
• The drain valves are
loose.
• eavy use, getting in
and out of pool.
• Pool too close to
trees.
• Super chlorinate with shock
treatment. Correct p to your
pool store's recommended
level.
• Vacuum pool bottom.
• Maintain proper chlorine
level.
• Adjust p level to the
recommended level.
• Run filter until water is clear.
• Clean cartridge frequently.
• Correct the p level. Check
with your pool dealer for
advice.
• Adjust the chlorine level.
• Clean or replace your filter.
• Repair with a patch kit.
• Finger tighten all caps.
• Use Intex pool vacuum to
clean bottom of pool.
• Use Intex pool skimmer.
• Greenish water.
• Green or black
spots on pool liner.
•Pool liner is
slippery and/or has
a bad odor.
• Water turns blue,
brown, or black
when first treated
with chlorine.
• Water is cloudy or
milky.
• Level is lower than
on previous day.
• Dirt or sand on
pool floor.
• Leaves, insects
etc.
IMPORTANT
If you continue to experience difficulty, please contact our Consumer
Service Department for assistance. See back cover for contact information.

106A
SAVE THESE INSTRUCTIONS Page 13
(106) MODEL 638R FILTER PUMP ENGLIS 7.5” X 10.3” PANTONE 295U 06/23/2011
English
SSAAFFEETTYY GGUUIIDDEELLIIEESS
GE ERAL AQUATIC SAFETY
Water recreation is both fun and therapeutic. However, it involves
inherent risks of injury and death. To reduce your risk of injury, read
and follow all product, package and package insert warnings and
instructions. Remember, however, that product warnings, instructions
and safety guidelines cover some common risks of water recreation,
but do not cover all risks and or dangers.
For additional safeguards, also familiarize yourself with the following
general guidelines as well as guidelines provided by nationally
recognized Safety Organizations:
• Demand constant supervision. A competent adult should be appointed as
a “lifeguard” or water watcher, especially when children are in and around
the pool.
• Learn to swim.
• Take the time to learn CPR and first aid.
• Instruct anyone who is supervising pool users about potential pool
hazards and about the use of protective devices such as locked doors,
barriers, etc.
• Instruct all pool users, including children what to do in case of an
emergency.
• Always use common sense and good judgement when enjoying any
water activity.
• Supervise, supervise, supervise.

106A
SAVE THESE INSTRUCTIONS Page 14
(106) MODEL 638R FILTER PUMP ENGLIS 7.5” X 10.3” PANTONE 295U 06/23/2011
PARTS LIST
Your Krystal Clear™ Filter-Pump has been manufactured using the highest quality
materials and workmanship. All Intex products have been inspected and found free of
defects prior to leaving the factory. This Limited Warranty applies only to the Krystal
Clear™ Filter-Pump and accessories listed below.
The provisions of this Limited Warranty apply only to the original purchaser and is not
transferable. This Limited Warranty is valid for the period noted below from the date of the
initial retail purchase. Keep your original sales receipt with this manual, as proof of
purchase will be required and must accompany warranty claims or the Limited Warranty is
invalid.
Krystal Clear™ Filter-Pump Warranty – 1 Year
oses, Plunger Valves & Fittings Warranty – 180 days
If a manufacturing defect is found within the periods noted above, please contact the
appropriate Intex Service Center listed in this manual. The Service Center will determine
the validity of the claim.
IMPLIED WARRANTIES ARE LIMITED TO T E TERMS OF T IS WARRANTY AND IN
NO EVENT S ALL INTEX, T EIR AUT ORIZED AGENTS OR EMPLOYEES BE LIABLE
TO T E BUYER OR ANY OT ER PARTY FOR DIRECT OR CONSEQUENTIAL
DAMAGES OR LIABILITIES.
This Limited Warranty does not apply if the products are subject to negligence, abnormal
use or operation, accident, improper operation, improper voltage or current contrary to
operating instructions, or to damage by circumstances beyond Intex’s control, including but
not limited to, ordinary wear and tear and damage caused by exposure to fire, flood,
freezing, rain, or other external environmental forces. This Limited Warranty applies only to
those parts and components sold by Intex. The Limited Warranty does not cover
unauthorized alterations, repairs or disassembly by anyone other than Intex Service
Center personnel.
The Limited Warranty is also not applicable if this product is used with another product
other than an Intex product, when setting up your pool.
The costs associated with the loss of pool water, chemicals or water damage are not
covered by this warranty. Injury or damage to any property or person is not covered by this
warranty.
LIMITED WARRANTY
English

106A
SAVE THESE INSTRUCTIONS Page 15
(106) MODEL 638R FILTER PUMP ENGLIS 7.5” X 10.3” PANTONE 295U 06/23/2011
AREAS LOCATIO AREAS LOCATIO
For service questions or to order replacement parts, please contact the appropriate office
listed below or visit www.intexdevelopment.com for answers to most frequently asked
questions.
English
• ARGENTINA ARSE INDUSTRIAL Y COMERCIAL S.A
MANUEL GARCIA 124 (CP1284)
CIUDAD AUTÓNOMA DE BUENOS AIRES,
ARGENTINA.
TEL: [phone] (interno 139);
TEL: [phone]( interno 145)
E-mail: Martín Cosoleto: [email protected]
E-mail: Daniel Centurion: [email protected]
Website: www.jarse.com.ar
• PERU COMEXA S.A.
AVENIDA COMANDANTE ESPINAR 142,
MIRAFLORES, LIMA, PERÚ
TEL: [phone]
• SAUDI ARABIA SAUDI ARABIAN MARKETING &
AGENCIES CO. LTD.
PRINCE AMIR MA ED STREET,
AL-SAFA DISTRICT. EDDAH,
KINGDOM OF SAUDI ARABIA
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
Website: www.samaco.com.sa
• AUSTRIA STEINBACH VERTRIEBSGMBH
AISTINGERSTRAßE 2
4311 SCHWERTBERG
TEL: 0820 - 200 100 200
(0,145€/min aus allen Netzen)
FAX: + 43 (7262) 61439
E-mail: [email protected]
Website: www.intexcorp.at
• CZECH REPUBLIC / INTEX TRADING S.R.O.
EASTERN EUROPE BENESOVSKA 23,
101 00 PRAHA 10,
CZECH REPUBLIC
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
• BELGIUM N.V. SIMBA-DICKIE BELGIUM S.A.
MOESKROENSESTEENWEG 383C,
8511 AALBEKE, BELGIUM
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
E-mail: [email protected]
Website: www.nicotoy.be/downloads.htm
• DENMARK K.E. MATHIASEN A/S
SINTRUPVE 12, DK-8220
BRABRAND, DENMARK
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
Website: www.intexnordic.com
• SWEDEN LEKSAM AB
BRANDSVIGSGATAN 6,
S-262 73 ÄNGELHOLM,
SWEDEN
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
Website: www.intexnordic.com
• NORWAY NORSTAR AS
PINDSLEVEIEN 1,
N-3221 SANDEF ORD,
NORWAY
TEL: [phone]
FAX: [phone]
E-mail: [e-mail]
Website: www.intexnordic.com
• FINLAND NORSTAR OY
SUOMALAISTENTIE 7,
FIN-02270 ESPOO,
FINLAND
TEL: [phone]
FAX: [phone]
E-mail: [e-mail]
Website: www.intexnordic.com
• RUSSIA LLC BAUER
KIEVSKAYA STR., 20,
121165 MOSCOW, RUSSIA
TEL: [phone]/9802
FAX: [phone]
E-mail: [email protected]
Website: www.intex.su
• POLAND KATHAY HASTER
UL. LUTYCKA 3, 60-415 POZNAN
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
Website: www.intexpoland.pl
• HUNGARY RECONTRA LTD./RICKI LTD.
H-1113 BUDAPEST, DARÓCZI ÚT 1-3,
HUNGARY
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
• BRASIL KONESUL MARKETING & SALES LTDA
RUA ANTONIO DAS CHAGAS,
1.528 - CEP. 04714-002,
CHÁCARA SANTO ANTONIO - SÃO
PAULO - SP - BRASIL
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
• ISRAEL ALFIT TOYS LTD
MOSHAV NEHALIM,
MESHEK 32, 49950, ISRAEL
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
• ASIA INTEX DEVELOPMENT CO. LTD.
9TH FLOOR,
DAH SING FINANCIAL CENTRE,
108 GLOUCESTER ROAD,
WANCHAI, HONG KONG
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
Website: www.intexdevelopment.com
• EUROPE INTEX TRADING B.V.
POSTBUS 1075, 4700 BB ROOSENDAAL,
THE NETHERLANDS
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
Website: www.intexcorp.nl
• FRANCE UNITEX / INTEX SERVICE FRANCE S.A.S
Z.A. DE MILLEURE
BOIS DU BAN - N°4
71480 LE MIROIR
TEL: [phone] (0,15€/min)
FAX: [phone]
Website: www.intex.fr
• GERMANY STEINBACH VERTRIEBSGMBH
C/O WEBOPAC LOGISTICS GMBH
INTER-LOGISTIK-PARK 1-3
87600 KAUFBEUREN
TEL: [phone]
(0,14€/min aus dem Festnetz, Mobilfunk max. 0,42€/min)
FAX: + 43 (7262) 61439
E-mail: [email protected]
Website: www.intexcorp.de
• ITALY A & A MARKETING SERVICE
VIA RAFFAELLO SANZIO 19
20852 VILLASANTA (MB)
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
Website: www.intexitalia.com
• UK OHN ADAMS LEISURE LTD
MARKETING HOUSE,
BLACKSTONE ROAD,
HUNTINGDON, CAMBS.
PE29 6EF. UK
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
Website: www.intexspares.com
•SWITZERLAND GWM AGENCY
GARTEN-U. WOHNMÖBEL,
RÄFFELSTRASSE 25,
POSTFACH,
CH-8045 ZURICH/SWITZERLAND
TEL: [phone] or [phone]
FAX: [phone]
E-mail: [email protected]
Website: www.gwm.ch, www.gwmsale.ch
• SPAIN / PORTUGAL Nostrum Iberian Market S.A.
Av. de la Albufera, 321
28031 Madrid, Spain
TEL: [phone]
FAX for Spain: [phone]
Email for Spain: [email protected]
FAX for Portugal: [phone]
Email for Portugal: [email protected]
Website: www.intexiberian.com
• AUSTRALIA HUNTER PRODUCTS PTY LTD
LEVEL 1, 225 BAY STREET,
BRIGHTON, VICTORIA,
AUSTRALIA
TEL: [phone] or 1800-224-094
FAX: [phone]
E-mail: [email protected]
Website: www.hunterproducts.com.au
• NEW ZEALAND HAKA NEW ZEALAND LIMITED
UNIT 4, 11 ORBIT DIVE, ALBANY,
AUCKLAND 0757, NEW ZEALAND
TEL: [phone]
FAX: [phone]
E-mail: [email protected]
Website: www.hakanz.co.nz
• MIDDLE EAST FIRST GROUP INTERNATIONAL
REGION AL MOOSA GROUP BUILDING, 1ST
FLOOR, OFFICE 102 & 103, UMM HURAIR
ROAD, KARAMA, DUBAI, UAE
TEL: [phone]INTEX(46839) / [phone]
FAX: [phone]
E-mail: [email protected].
Website: www.firstgroupinternational.com
• SOUTH AFRICA WOOD & HYDE
15-17 PACKER AVENUE, INDUSTRIA 2,
CAPE TOWN, SOUTH AFRICA 7460
TEL: [phone] (Toll Free) or 27-21-505-5500
FAX: [phone]
E-mail: [email protected]
• CHILE / URUGUAY COMEXA S.A.
EL UNCAL 100, PARQUE INDUSTRIAL PORTEZUELO,
QUILICURA, SANTIAGO, CHILE.
TEL: [phone]
E-mail: [email protected]