Intex Quickfill AP619D User manual

(17PO) AP619D/AP619DP-22 ELECTRIC PUMP ENGLISH 4.875” X 7.25” 12/04/2021
English 17PO
READ AND SAVE THESE INSTRUCTIONS
Page 1
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT
INTEX® OWNER’S MANUAL
Quickfill®Plus Internal Pump
Model AP619D 110V – 120V~ 60Hz 0.65A
Model AP619DP 110V – 120V~ 60Hz 0.85A
• To reduce the risk of electric shock: Always unplug this furnishing from the electrical outlet before cleaning.
DANGER
017-*PO-R0-2212
To reduce the risk of burns, fire, electric shock, or injury to persons:
• Infants have suffocated on inflatable mattresses. Never place infant aged birth to 15 months to sleep on this
inflatable air mattress / air bed. Infants can suffocate on an underinflated or deflated mattress, on bedding, by
co-sleeping with another person, and by entrapment between the mattress and bed frame or between the
mattress and a vertical surface.
• Childrencanbeentrappedbetweentheinflatablemattressandanadjacentverticalsurface.Provideatleast 
a shoulder width space between the inflatable mattress / airbed and adjacent vertical surfaces such as walls,
dressers or other objects.
• Alwayskeeptheinflatablemattressfullyinflatedwheninuse.
• Neverintroduceanyflammablesubstanceintotheinflatableairbed,SUCHASAEROSOLTIREREPAIR 
 PRODUCTS,asitmayigniteorexplode.
• Forindoorhouseholduseonly.
• Unplugfromoutletbeforeputtingonortakingoffparts.
• Closesupervisionisnecessarywhenthisfurnishingisusedby,ornearchildren,invalids,ordisablepersons.
• Usethisfurnishingonlyforitsintendeduseasdescribedintheseinstructions.Donotuseattachmentsnot
recommended by the manufacturer.
• Donotoperatewhereaerosol(spray)productsarebeingusedorwhereoxygenisbeingadministered.
• Thisisnotatoy.Childrenmustnotbeleftunattendedwhenusingtheairbed.
• Ifastoragebagisincluded,keepthestoragebagawayfrombabiesandchildren.Thestoragebagisnota 
toy. When not in use, fold the bag and put it away out of the reach of children.
• Donotwalk,standonorjumponorusetheairbedasatrampoline.
• Donotuseonornearwater.Thisisnotaraft.
• Donotsetupbednearstairs,doors,sharpedgesorbreakableobjects.Provideadequatespacebetweenbed
and objects to avoid entrapment.
•
Make sure the area is flat, smooth, free of sharp objects that could puncture the bed and keep away from ledges.
• Keeppetsawayfromtheairbed.Petsmaypuncturethesurfaceofthebed.
• Avoidsleepingontheedgeoftheairbed.Edgesproducelesssupportthanthemiddleofthebed.
• Donotoperateairpumpformorethan5minutesatatime.Letpumpcoolatleast15minutesbetweenuse.
• Unplugelectricalpowercordwhennotinuse.Todisconnect,turnallcontrolstotheoffposition,thenremove
plug from outlet.
• Neveroperatethefurnishingwiththeairopeningsblocked.Keeptheairopeningsfreeoflint,hair,andthelike.
Never drop or insert object into any opening.
•
Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped
 ordamaged,ordroppedintowater.Returnthefurnishingtoaservicecenterforexaminationand/orrepair.
• IftheACsupplycordisdamaged,itmustbereplacedbythemanufactureroritsserviceagentinorderto 
avoid a hazard.
• Donotruncordundercarpeting.Donotcovercordwiththrowrugs,runners,orsimilarcoverings.Donotroute
cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
 Keepthecordawayfromheatedsurfaces.
FOLLOW THESE RULES AND ALL INSTRUCTIONS TO AVOID SUFFOCATION, PROPERTY DAMAGE,
ELECTRIC SHOCK, BURNS OR OTHER INJURY.
WARNING
•
Toreducetheriskofelectricshockorinjury,useindoorsonly,donotexposetorain.Storeindoors.
CAUTION

(17PO) AP619D/AP619DP-22 ELECTRIC PUMP ENGLISH 4.875” X 7.25” 12/04/2021
English 17PO
READ AND SAVE THESE INSTRUCTIONS
Page 2
NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale.
Duetoapolicyofcontinuousproductimprovement,Intexreservestherighttochange
specifications and appearance, which may result in updates to the instruction manual,
without notice.
PARTS REFERENCE
OPERATING INSTRUCTIONS
General
• Thisappliancehasapolarizedplug(onebladeiswiderthantheother).Thisplugwillfit
in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the
 plug.Ifitstilldoesnotfit,contactaqualifiedelectriciantoinstalltheproperoutlet.Donot
change the plug in any way.
• AirbedsaredesignedfortemporaryuseandareNOTdesignedtobeareplacementfora
traditional mattress.
• Makesuretheareaisflat,level,cleanandfreefromsharpobjects,andwithinreachof
an electrical outlet.
• Topreventpunctureordamagetotheairbed,neverdragtheairbedacrossthefloor.Lift
the inflated airbed when moving or changing location.
Maintenance instructions:
• Noairpumpmaintenanceisrequired.Pumpisremovable.
• Forcleaninguseonlycleanclothwithmildsoapysolution.Donotuseanychemicals.
• Incaseofrepairs,useonlycommonPVCrepairglueandpatches.Forflockedsurfaces:rub
away the flocking material with an eraser first before applying the glue and/or patch.
SERVICING OF A DOUBLE-INSULATED PRODUCT:
In a double-insulated product, two systems of insulation are provided instead of grounding.
No grounding means is provided on a double-insulated product, nor should a means for
groundingbeaddedtotheproduct.Servicingofadouble-insulatedproductrequiresextreme
careandknowledgeofthesystem,andshouldbedoneonlybyqualifiedservicepersonnel.
Replacement parts for a double-insulated product must be identical to those parts in the
product.Adouble-insulatedproductismarkedwiththewords“DOUBLEINSULATION”or
“DOUBLEINSULATED”andwiththesymbol.
Part Descriptions:
1. Pump holder frame
2. Pump removal tab
3. Cordcompartment
4. ACpower cord
5. Manual inflation port cap
6. Manual inflation port
7. Cordcompartmentcover
8. Air passage
9. Control dial
10. Airbed front
11.Closed/Pump Off Position
2
3
45
6
7
1
8
10 9
11

(17PO) AP619D/AP619DP-22 ELECTRIC PUMP ENGLISH 4.875” X 7.25” 12/04/2021
English 17PO
READ AND SAVE THESE INSTRUCTIONS
Page 3
3. Turn the control dial fully clockwise until it stops. The pump turns on automatically to
inflate the airbed.SeeFig(3).
4. When the airbed is fully inflated, turn the control dialback(counterclockwise)tothe
center position which closes the valve and turns the pump off. SeeFig(4).
NOTE: Turning the control dial either direction while the pump is unplugged will let air
escapefromtheairbed.Seestep#5forfirmnessadjustmentinstructions.
Never disconnect the power cord from the electrical outlet while the pump is running. Rotate
control dial to the closed / pump off position before disconnecting the power cord.
5. If the airbed feels too firm, release some air by simply turning the control dial gradually
counterclockwise until air begins to escape from the air passage. When the desired
firmness is achieved, turn the control dial back to the center closed / pump off position. If
the airbedfeelstoosoft,repeatsteps#3to#5asnecessary.
INFLATION
1. Open cord compartment cover and remove power cord. Do not yank on the cord.
SeeFig(1).
2. PlugintheACpower cordintoanACelectricaloutlet.SeeFig(2).
FIG (1) FIG (2)
110V–120V
220V–240V
√
FIG (3)
Inflate
Position
FIG (4)
RotatetoClosed/PumpOffPosition

(17PO) AP619D/AP619DP-22 ELECTRIC PUMP ENGLISH 4.875” X 7.25” 12/04/2021
English 17PO
READ AND SAVE THESE INSTRUCTIONS
Page 4
Proper inflation of the airbed.
The ambient temperatures of air have an effect on the airbed internal pressure. At low
ambient temperature the air will contract within the airbed and the airbed will feel softer:
addairasnecessary.Athighambienttemperaturetheairwithintheairbedwillexpand
significantly and the airbed will become hard and may burst: release air to avoid damage
to the airbed or to soften the feel. Do notexposetheairbedtoextremetemperatures
(hotorcold).
Stretchingisanaturalcharacteristicofnewvinyl.Duringinitialuse,theairbedmaybecome
softandrequireadditionalinflationtomaintaindesiredfirmness.Thisisnormalforthefirst
few days of use.
Dimensionsshownareapproximateandwillvaryduetothevinyltemperatureandtheair
temperature.
In no event shall Intex, their authorized agents or employees be liable for damages
(such as pin holes) to the airbed caused by negligence, ordinary wear and tear,
abuse and carelessness, or external forces.
IMPORTANT NOTE
DEFLATION
1. PlugintheACpowercordintoanACelectricaloutlet.SeeFig(2).
2. Turn the control dial fully counterclockwise until it stops. The pump is now deflating the
airbed.SeeFig(5).
3. When all the air is removed from the airbed, turn the control dialback(clockwise)tothe
center position which closes the valve and turns the pump off.
4. DisconnecttheACpower cord from the electrical outlet, coil the power cord and place it
inside the cord compartment, then close the cover. Make sure the power cord is free of
twists, kinks or knots.
5. With the airbed fully deflated begin rolling the airbed from the end opposite of the pump
 towardstheendwherethepumpislocated.SeeFig(6).
MANUAL INFLATION OPTION
If electrical power is not available, a conventional foot, manual, or battery-operated air
pump can be used by connecting it to the manual inflation port located inside the power cord
compartment. SeeFig(7).Followthesesteps:
FIG (5)
Deflate
Position
FIG (6)

(17PO) AP619D/AP619DP-22 ELECTRIC PUMP ENGLISH 4.875” X 7.25” 12/04/2021
English 17PO
READ AND SAVE THESE INSTRUCTIONS
Page 5
1. Open cord compartment cover and locate the
manual inflation port.
2. Make sure the control dial of the internal electric
pump is still in the closed / pump off position.
3. Remove the cap from the manual inflation port and
insert the nozzle of the pump into the port. Inflate the
airbed to desired firmness.
NOTE: Do not overinflate. The firmness should be
approximatelythesameasthelevelachievedwiththe
internal electric pump.
4. Remove nozzle from manual inflation port and close
the cap and the cord compartment cover.
STORAGE INSTRUCTIONS
1. Deflatetheairbedfollowingthe“DEFLATION”instructions.
2. Make sure the airbed is clean and dry.
3. Laytheairbedflatwiththesleepingsurfacefacingupwardsandfollowthefoldingsteps
on Figs(8-12).Foldtheairbedlooselyandavoidsharpbends,cornersandcreases
which can damage the airbed.
REPLACING INTERNAL AIR PUMP OR THE AIRBED COMPONENT
If there is a need to replace either the internal air pump or the airbed portion, detach the
internal pump from the airbed as follows:
1. While holding both lock tabs pressed inward(seeFigure13), turn the round body of the
 pump(thelargeouterrim,notthe control dial)counterclockwiseandpulltheairpump 
body out of the holder frame.
2. Dependingonwhichpartisbeingreplaced,keeptheremainingcomponent(eitherthe
 airbedportionortheremovedpump)inasafeplaceuntilthereplacementpartis
received. Reattach the components when the new part is received: simply place
the pump into the holder frame and turn clockwise untill the lock tabs click into place.
NOTE: Make sure the rubber seal on the pump housing as well as the inside wall of the
holder frame are clean and free from any lint, hair or dirt, to ensure a proper seal and avoid
air leaks.
NOTE: Do not remove internal air pump from the holder frame other than for servicing, as
this may introduce lint, hair or dirt into the seal area and cause air leaks. If air leak is
experienced,checkthatthesealiscleanbeforereplacingthepumportheairbed.
FIG (7)
FIG (8) FIG (9) FIG (10) FIG (12)
FIG (11)
FIG (13)
1
2
1

(17PO) AP619D/AP619DP-22 ELECTRIC PUMP ENGLISH 4.875” X 7.25” 12/04/2021
English 17PO
READ AND SAVE THESE INSTRUCTIONS
Page 6
©2021 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Recreation Corp. All rights reserved/Tous droits réservés/Todos los derechos
reservados/Alle Rechte vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™Trademarksusedinsomecountriesoftheworldunderlicensefrom/®™Marquesutiliséesdanscertainspayssouslicencede/Marcasregistradas
utilizadasenalgunospaísesdelmundobajolicenciade/WarenzeichenverwendetineinigenLändernderWeltinLizenzvon/Intex Marketing Ltd. to/à/
a/an Intex Development Co. Ltd., Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801•DistributedintheEuropeanUnion
by/Distribuédansl’UnionEuropéennepar/DistribuidoenlauniónEuropeapor/VertriebinderEuropäischenUniondurch/Intex Trading B.V., Venneveld
9, 4705 RR Roosendaal – The Netherlands
www.intexcorp.com
PROBLEM CAUSE SOLUTION
Air leakage
between internal air
pump and the pump
holder frame
•Pumpnotsecurely
attached.
•PumpO-ringis
dirty.
•Internalairbed
beam threads are
caught between
the internal air
pump and the
pump holder frame.
•PumpO-ringis
twisted and/or
damaged.
•Whileholdingthepumpouterrim,pushinand
turn the pump fully clockwise until the two side
tabs lock into place.
•Remove the pump from the airbed, remove
the O-ring from the pump and clean it with
water.CarefullyreplacetheO-ringbacktothe
pump as to prevent dust, lint from sticking onto
the O-ring again. Also make sure the pump
holder frame inner wall is free from dust, hair
or lint.
•Removetheinternalairpumpandcarefully
replace the pump back making sure the internal
airbed beam threads are away from the pump
holder frame.
•Removethepumpfromtheairbed,makesure
the O-ring is not damaged and/or twisted.
Realign the O-ring or replace a new O-ring.
ContactIntexservicecenterforreplacement.
Air pump does not
work
•Notconnectedto
an electrical outlet
socket.
•Pumpmotor
thermo-protector
activated.
•Internalairpump
defective.
•Makesurethepumpispluggedintothe
correct power outlet, then turn the control dial
fully clockwise to the inflation position.
•
Turn off and disconnect the power cord from the
power outlet, let the pump rest for more than
30 minutes before resume the use of the pump.
•Remove the internal air pump from the airbed
andkeeptheairbedinasafeplace.Contact
Intexservicecenterforaninternalairpump
replacement.
Pump motor is
running but airbed
isnotinatingor
deating
•Theinflationor
deflation mode is
not set yet.
•
Turn the control dial fully clockwise until it
stops to inflate the airbed. Or turn the control
dial fully counterclockwise until it stops to
deflate the airbed.
Afterinationairis
escaping through
the pump air
passage or through
themanualination
port
•Thepumpair
passage is not
completely closed.
•Themanual
inflation port cap is
not securely closed.
•Makesuretheairpassageisclosedby
turning the control dial to the center closed /
pump off position.
•Pushthecapfirmlyintothemanualinflation
port.
TROUBLESHOOTING GUIDE