Invacare 1335 User manual

Part No. 00083x072 1Non-Folding Device
For more information regarding Invacare products, parts, and services,
please visit www.invacare.com
Non-Folding Device
Model No. 1335
NOTE: Check all parts for shipping damage. In case of damage, DO NOT use. Contact
Carrier/Invacare for further instructions.
Safety Summary
To ensure the safe and proper installation and adjustment of the Non-Folding Device,
these instructions MUST be followed:
 WARNING
DO NOT use this equipment without first reading and understanding this instruction
sheet and the owner’s manual supplied with the product. If you are unable to
understand the warnings, cautions and instructions, contact a healthcare professional,
dealer or technical personnel if applicable, before attempting to install this equipment
- otherwise, injury or damage may occur.
Invacare products are specifically designed and manufactured for use in conjunction
with Invacare accessories. Accessories designed by other manufacturers have not
been tested by Invacare and are not recommended for use with Invacare products.
After any adjustments, repair or service and before use, make sure all attaching
hardware is tightened securely - otherwise injury or damage may occur.
DO NOT overtighten the attaching hardware when securing the non-folding device to
the wheelchair frame, otherwise damage to the hardware and/or wheelchair frame
may occur.
The non-folding device kit contains the following items:
NOTE: If the non-folding device will not fit on the wheelchair, contact an Invacare Dealer.
NOTE: The non-folding device is not designed to narrow the width of the wheelchair.
Installing the Non-Folding Device
NOTE: For this procedure, refer to FIGURE 1.
1. Remove the locknut and the hex head bolt from the clamps at both ends of the
non-folding device.
2. Loosen, but DO NOT remove the locknut on the lug bolt on the adjustment clamp.
Assembly, Installation and Operating Instructions
SAVE THESE INSTRUCTIONS
DESCRIPTION QUANTITY
Lug Bolt 1
Locknut 3
Non-Folding Device 1
Hex Head Bolt 2
Plastic Insert Guide 2

3. Determine an acceptable mounting location for the non-folding device.
NOTE: The location depends on the wheelchair model. The non-folding device can be mounted to
7/8-inch (using plastic insert guide) or 1-inch diameter tubing. For any wheelchair model, it can
be installed on to at least one of the following locations:
A. Rear upright tubes (Detail “A”)
B. Rear step tubes (Detail “A”)
C. Upper frame tubing (Detail “B”)
NOTE: When mounting on the upper frame tubing under the seat, the non-folding device MUST
be mounted just in front of the rear seat guides.
4. Unfold the wheelchair. Refer to owner’s manual supplied with the wheelchair.
5. Position one clamp of the non-folding device in the pre-determined position from STEP
3 as shown in FIGURE 1. If you are mounting this device on 7/8-inch tube, put the plastic
insert guides around the 7/8-inch tube under the clamps.
6. Squeeze the two halves of the clamp together.
7. Insert the hex head bolt through the clamp.
8. Install the locknut onto the hex head bolt.
9. Extend the non-folding device to position the remaining clamp on the opposite side of
the wheelchair in the position determined in STEP 3.
10. Repeat STEPS 5-7 to secure the remaining clamp.
NOTE: Ensure clamps at both ends sit flush on the wheelchair frame and DO NOT interfere with
wheelchair function.
11. Securely tighten the locknuts on the hex head bolts in the clamps at both ends of the
non-folding device.
12. Securely tighten the locknut on the lug bolt in the adjustment clamp.
FIGURE 1 Installing the Non-Folding Device
Locknuts Rear Upright
Tube
Clamp
Adjustment
Clamp
Hex Head Bolt
Rear Step
Tube
DETAIL “A” DETAIL “B”
Adjustment
Clamp
Rear Seat
Guides
Hex
Head Bolt
Locknuts
Upper Frame
Tubing
Clamp
Lug
Bolt
Invacare Corporation www.invacare.com
USA
One Invacare Way
Elyria, Ohio USA
44036-2125
800-333-6900
Canada
570 Matheson Blvd E Unit 8
Mississauga Ontario
L4Z 4G4 Canada
800-668-5324
Invacare, Yes, you can. and The Medallion
Design are registered trademarks of
Invacare Corporation.
©2006 Invacare Corporation
Part No. 00083x072
Rev F - 05/3/06