involight LED MH78W User manual

Bedienungsanleitung
User manual
LED MH78W
www.destilan-deutschland.de

1
Table of contents
INTRODUCTION ……………………………………………….…………………………..2
SAFETY INSTRUCTIONS…………………………………………………………………2
OPERATING DETERMINATIONS…………………………………………….…………..3
DESCRIPTION OF THE DEVICE…………………………………………………………4
INSTALLATION………………………………………………………………….…………..5
OPERATION……………………………………………………………………….………...6
Stand alone operation…………………………………………………………….…………6
Master slave operation…………………………………………………………….……..…6
DMX controlled operation………………………………………………………….…….…6
Addressing…………………………………………………………………………….…..…6
Control board………………………………………………………………………….…..…6
DMX protocol………………………………………………………………………….…..…7
TECHNICAL SPECIFICATIONS…………………………………………………….……7

2
Every person involved with installation. operation and maintenance of this fixture has to
- be qualified
- follow the instruction of this manual
- consider this manual to be part of the total product
- Keep this manual for the entire service life of the product
- pass this manual to every future owner or use of the product
INTRODUCTION
Thank you for choosing our fixture, if you follow up the instruction given in this manual we be sure that
you will enjoy this product for a long period of time
SAFETY INSTRUCTION
This device has left our premises in absolutely perfect condition .In order to maintain this condition and
to ensure a safe operation, it is absolutely necessary for the user to follow the safety instruction and
warning notes written in this user manual.
Important: Damages caused by the disregard of this user manual are not subject o warranty, the dealer
will not accept liability for any resulting defects of problem. If the device had been exposed to drastic
temperature fluctuation (e.g. after transportation),do not switch it on immediately. The arising
condensation water might damage your device. Leave the device switched off until it had reached room
temperature. Please make sure that there are no obvious transport damages, should you notice any
damages on the AC connection cable or on the casing, do not take the device into operation and
immediately consult your local dealer.
The device falls under protection-class. The power plug must only be plugged into a protection class I
outlet. The voltage and frequency must exactly be the same as stated on the device. Wrong voltages or
power outlets can lead to the destruction of the device and mortal electrical shock.Always plug in the
power plug last. The power plug must always be inserted without force .Make sure that the plug is tightly
connected with the outlet.
Never let the power-cord come into contact with other cables! Handle the power-cord and all
connections with the mains with particular caution! Never touch them with wet hands .as this could lead
CAUTION!
Be careful with your operations, With a dangerous voltage you can suffer a dangerous electric
shock when touching the wires.
CAUTION !
Keep this device away from rain and moisture
Unplug mains lead before opening the housing
For your own safety, please read this user manual carefully before you initially start-up

3
to mortal electrical shock. Never modify, bend, strain mechanically, put pressure on, pull or heat up the
power cord. Never operate next to sources of heat or cold. Disregard can lead to power cord damages,
fire or mortal electrical shock. The cable insert or the female part in the device must never be strained.
There must always be sufficient cable to the device. Otherwise, the cable may be damaged which may
lead to mortal electrical shock. Make sure that the power-cord is never crimped or damaged by sharp
edges. Check the device and the power-cord from time to time.If extension cords are used, make sure
that the core diameter is sufficient for the required power consumption of the device. All warnings
concerning the power cords are also valid for possible extension cords.
DESCRIPTION OF THE DEVICE
Features
> 8/13 channel DMX-512 .
> Pan :540°/tilt:180°.
> Variable electronic strobe.
> Variable electronic dimmer(0-100%).
> LED display menu with invert.
> Reset to factory settings option.
> Pan/tilt invert option.
> Fan cooled.
INSTALLATION
Rigging
The installation of the projector has to be built and constructed in a way that it can hold 10 times the
weight for 1 hour without any harming deformation.
IMPORTANT!OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating
working load limits, installation material being used, and periodic safety inspection of all installation
material and the projector. If you lack these qualifications, do not attempt the installation yourself, but
instead use a professional structural rigger. Improper installation can result in bodily injury and or
damage to property. The projector had to be installed out of the reach of people
DANGER OF FIRE! When installing the device, make sure there is no highly-inflammable
material(decoration articles, etc.)within a distance of min.0.5m.
DMX 512 connection/ connection between fixture
The wires must not come into contact with each other, otherwise the fixture will not work at all or
properly. Please note the starting address depends upon which controller is being used. Only use a
DMX cable and 3-pin XLR-plugs and connectors in order to connect the controller with the fixture or one
fixture to another

4
Connection with the mains.
The earth has to be connected. The device must only be connected with an electric installation carried
out in compliance with IEC standards.
OPERATION
After you connected the effect to the mains, The fixture starts running
Stand Alone operation
In the stand alone mode, the fixture can be use without controller
Master/slave-operation
The master/slave-operation enables that several devices can be synchronized and controlled by one
master-device
DMX controlled operation
You can control the projectors individually via your DMX-controller
Addressing
The control board allows you to assign the DMX starting address,
Note;it’s necessary to insert the XLR termination plug (with 120ohm) in the last device in the link in order
to ensure proper transmission on the DMX data link.
CONTROL BOARD
The control board offer several features :you can simple set the starting address, run the
pre-programmed program or make a reset
the main menu is accessed by pressing the Mode/Esc-button, Browse through the submenu by
pressing Up or Down .Press the Enter-button in order to select the desired menu. You can change the
selection by pressing Up or Down, Confirm every selection by pressing the Enter-button. You can leave
every mode by pressing the Mode/Esc-button .The functions provided are described in the following
setting.

5
MENU MAP
The device has two operation modes, It can be operated in Stand Alone or in DMX controlled
d001 001-512 DMX mode and set address
MAFA FASt Master auto mode in fast
MStS Master sound mode
MStc Stand-alone mode
SlAu Slave mode
MASL-SLOU Master atuo mode in slowly
PAn PAn/rPAn Pan reverse
TiL TiL/rTiL Tilt reverse
diS diS/rdiS display reverse
13ch 13/8ch 13/8channel mode
PA54 PA54/36/18 Pan movement angle select 540036001800
Ti27 18/09 Titl movement angle select 1800900
REST rest
LOAD Default setting
Note：output default setting address code is A001, pan is positive circumrotate、tilt is positive
circumrotate、LED positively reveal.
DMX-protocol
13 DMX channel mode
Channel Value Function
1
0-255 Pan Pan movement 0~630
2
0-255 Pan Fine Pan fine
3
0-255 Tilt Tilt movement 0~180
4
0-255 Tilt Fine Pan fine
5
0-255 Pan/Tilt Speed Adjust pan/tilt speed
6
0-7
8-134
135-239
240-255
Dimmer and Strobe
No function
0-100% Dimmer
Strobe from slowly to fast
Open
7
0-255 Red 0-100% Red
8
0-255 Green 0-100% Green

6
9
0-255 Blue 0-100% Blue
10
0-255 White 0-100% White
11 0-9
10-255
Mix color
No function
32 different color change
12
0-255 Mix color speed Mix color speed adjustment
13
0-255 Auto program Auto program
8 DMX channel mode
Channel Value Function
1
0-255 Pan Pan movement 0~630
2
0-255 Tilt Tilt movement 0~180
3
0-7
8-134
135-239
240-255
Dimmer and Strobe
No function
0-100% Dimmer
Strobe from slowly to fast
Open
4
0-255 Red 0-100% Red
5
0-255 Green 0-100% Green
6
0-255 Blue 0-100% Blue
7
0-255 White 0-100% White
8
0-255 Pan/Tilt Speed Adjust pan/tilt speed

7
TECHNICIAL SPECIFICATIONS
Model LED MH78W
Voltage 110V- 250V / 50-60Hz
Power consumption: 85W
LED 7pcs 8w RGBW Quad LEDs
Gross Weight 3.5Kgs
Dimensions 28(H) x 22(W) x 27(L) mm
www.destilan-deutschland.de
http://acctech.ru/cat/vrashhayushhiesy_golovy/