InWin Cobra IW-RS212-07 User manual

IW-RS212-07
User Manual

Table of Contents
PREFACE ..................................................................................................................................... 1
SAFETY INFORMATION ............................................................................................................... 1
CAUTION .................................................................................................................................... 2
SPECIFICATIONS .......................................................................................................................... 3
12Gb/s Backplane Spec f cat ons ................................................................................................ 4
1 Product Introduct on ........................................................................................................... 5
1.1 Box Contents .......................................................................................................................... 5
1.2 General Information ............................................................................................................... 6
1.2.1 Front anel Controls and Indicators ............................................................................... 7
1.2.2 Rear anel Configuration ................................................................................................ 8
2 Hardware Installat on ......................................................................................................... 9
2.1 Removing and Installing a Hard Drive ...................................................................................... 9
2.1.1 Installing a Hard Drive ..................................................................................................... 9
2.1.2 Removing a Hard Drive .................................................................................................. 10
2.2 Removing and Installing the Top Cover.................................................................................. 11
2.3 Removing and Installing the Fan Module .............................................................................. 12
2.3.1 Removing the Fan Module ............................................................................................ 12
2.3.2 Installing the Fan Module.............................................................................................. 13
2.4 Removing and Installing the SU Module .............................................................................. 13
2.4.1 Removing the SU Module ........................................................................................... 13
2.4.2 Installing the SU Module ............................................................................................. 15
2.5 Removing and Installing the Rear 2.5” HDD For OS:................................................................... 15
2.5.1 Removing the Rear 2.5” HDD: ........................................................................................ 15
2.5.2 Installing the Rear 2.5” HDD: ......................................................................................... 16
2.6 Installing the Slide Rail ......................................................................................................... 17
2.6.1 Identifying the Slide Rail ............................................................................................... 17
2.6.2 Removing the Inner Rail and Sliding the Intermediate Rail Back ................................ 17
2.6.3 Attaching the Inner Rail to the Chassis ............................................................................ 18
2.6.4 Mounting the Rail Bracket to the Cabinet .................................................................... 19
2.6.5 Insert the Chassis to the Cabinet .................................................................................. 20
2.7 Installing the Motherboard ................................................................................................... 21
2.8 Connecting Cables ................................................................................................................ 21

2.8.1 Connecting Expander Through SAS Connectors ........................................................... 22
2.8.2 Connecting LED Cable, Front Control anel and Front USB I/O orts ......................... 22
3 Backplane Introduct on ..................................................................................................... 23
4 Compat b l ty L sts .............................................................................................................. 24
5 Q&A ................................................................................................................................. 25
6 Techn cal Support .............................................................................................................. 26

1
REFACE
hank you for choosing the InWin IW-RS212-07. his manual is written for system technicians who
are responsible for installation, troubleshooting, managing and repairing this server chassis. his
document provides the overview of all the features of the chassis, a list of accessories or other
components you may need to finish the installation, troubleshooting methods and instructions on
adding and removing components on the InWin IW- RS212-07. For the latest version of this
manual, you may visit InWin’s server website.
SAFETY INFORMATION
o ensure a safe and smooth operation of your InWin IW-RS212-07, it is essential that you choose
an appropriate location for the system, provide an appropriate operating environment and supply
an adequate amount power for all components of the system. As you plan for installation, follow
the guidelines below to ensure that the system and its environment are safely and appropriately
positioned for efficient operation and service. Your system should be installed and serviced only by
a qualified technician.
Environment selection: he system is designed to operate in a typical office environment:
•he location should be clean, dry and free of airborne particles.
•It should be placed in a well-ventilated room, and away from sources of heat including direct
sunlight and radiators.
•It should be kept away from sources of vibration or physical shock.
•he space should be accommodated with a properly grounded wall outlet, and with sufficient
space to access the power supply cords.
•he operating environment temperature should be around 0°C to 40°C (32°F to 104°F).
Heed safety instructions: Before working with InWin IPC/storage server products, we strongly
recommend you use this guide as a reference and follow the safety instructions. he instructions in
this manual will help you ensure and maintain compliance with existing product certifications and
approvals. Follow the described, regulated components mentioned in this manual. Use of non-UL
listing products or other regulators may not comply with product regulations in the region(s) in
which the product is sold.
System power on/off: he power button DOES NO totally turn off the system AC power. o
remove the power of the system, you must unplug the AC power cord from the outlet or the
system’s power supply units. Make sure the power cord is unplugged before you open the chassis,
add or remove any components.
Hazardous conditions, devices and cables: Hazardous electrical conditions can be present on/in
power supply units and their cables. Disconnect the power cord and any other devices attached to
the server before opening the case. Failing to follow safety procedures will increase the risk of
personal injury or equipment damage.

2
Electrostatic discharge (ESD) and ESD protection: In most cases, ESD may damage disk drives,
electronic boards and other parts. We recommend that you conduct installation only at an ESD
free space. If not possible, perform ESD protection protocol by wearing anti-static wrist straps
attached to the ground on any unpainted metal surface on your server during operation.
Installing or removing jumpers: A jumper is a short length conductor used to close, open or bypass
part of an electronic circuit. Jumpers on InWin backplanes have a small tab on top that you can
pick up with your fingertips. Grip the jumper carefully, and plug the jumper to cover the jumper
pins on the backplane. Once you need to remove the jumper, grip the jumper and carefully pull
without squeezing.
CAUTION
o avoid damage and maintain your safety, please read the following terms listed below:
1. Do not populate hard drives and turn on the power until the system has
stabilized.
Make sure hard drives and other components are properly connected before
turning on the system.
2. ighten or loosen all screws with a screwdriver.
3. Apply the correct screws packed in the accessory box.
4. For your safety, please have at least two people lift and install the unit in its
designated area.
5. Before mounting the unit to the cabinet, make sure the rail is installed correctly.
6. When installing and removing any module or part, please use the handles.

3
S ECIFICATIONS
Model Name IW-RS212-07
Standard EIA-RS310D
M/B Form Factor A X (12” x 9.6”), CEB (12” x 10.5”), EEB (12” x 13”)
Drive Bay External 2.5”/ Screwless 3.5" Hot-swap HDD ray x 12 (U.2 NVMe x 4)
Rear 2.5" Screwless Hot-swap HDD tray x 2
ower Supply
Supports:
• Form Factor: 80 Plus Platinum CRPS with PDB Cable Management
• Watt: 550W/800W/1200W
Indicator Power LED, LAN1/LAN2/LAN3/LAN4 LED, System LED, ID LED, HDD LED
Front Control anel Power On/Off, Reset, NMI, ID SW, USB 3.0 x 2
Backplane-1 Mini SAS HD 12Gb/s with Expander plus Slim Line x 4
Backplane-2 Mini SAS HD 12Gb/s with Expander plus OcuLink x 4
SAS 12G Expander Supports LSI 3x36R Expander
Cooling Fan 8038mm PWM Fan x 4
Expansion Slot Low-profile PCIe Slot x 7
Material Material: SGCC
hickness: 1.0mm
Rail Kit Supports 28" ool-less & Ball-bearing Slide Rail
roduct Dimensions
(D x W x H)
w/o Front Door
660 x 482.6 x 87mm
ackaging Dimensions
(D x W x H) 845 x 595 x 223mm
Shipping Information Net Weight: 14.81kg
Gross Weight: 18.23kg
Container Informatoin
Single Packing with Pallets:
20’: 160pcs
40’: 368pcs
40’HQ: 414pcs

4
12Gb/s BACK LANE S ECIFICATIONS
Backplane-1 RS212-07 Slimline Backplane
Dimension (W x H) 405mm x 72.3mm
Backplane Type Active with Expander Onboard
Host Interface 3x SFF-8643 4x SFF-8654 Slimline
HDD Interface 12x SAS/SA A or 8x SAS/SA A and 4x NVMe SSD
Backplane-2 RS212-07 Oculink Backplane
Dimension (W x H) 405mm x 72.3mm
Backplane Type Active with Expander Onboard
Host Interface 3x SFF-8643 4x SFF-8611 Oculink
HDD Interface 12x SAS/SA A or 8x SAS/SA A and 4x NVMe SSD
 he actual product is subject to change without prior notice. In Win Development Inc. reserves the
right to make any final modifications.
 Above image is for reference only. All hardware components and optional parts are not included.

5
1roduct Introduction
1.1 Box Contents
When you open the IW-RS212-07 box, the contents should include the following:

6
1.2 General Information
When you open the chassis, it should reflect the diagram’s image .
Rear top cover
CRPS redundant or single
power supply module
12 x 3.5” tool-less
HDD trays
Front controls and indicators
A X, CEB or EEB
motherboard
PWM fans (Max. 4pcs)
Rear 2.5” HDD for OS

7
1.2.1 Front anel Controls and Indicators
he IW-RS212-07 supports SAS/SA A 12 x 3.5” disk bays or SAS/SA A 8 x 3.5” with
NVMe 4 x 3.5” disk bays in specific areas. he control panel, USB IO ports and
indicators are located on the handles.
Name Color Status Description
1 System Reset Button N/A Press the button to activate system reset
2 NMI Button N/A Press the button to activate user define
3 Power On/Off Button with
LED
Green
Solid on
System is powered on
N/A Off System is off
4 Chassis ID Button with LED Blue Solid on
Press the button to activate system identification
5
Hard Disk LED Amber
Blinking
System HDD accessing
6 System Fail LED Amber
Solid on
System Status ( - , + )
Green
Solid on
System Status ( + , - )
7 LAN LED (From top to
bottom ranked LAN1 - LAN4)
Green Blinking
Link between system and network
N/A Off No data transmission or receiving is occurring
8 USB 3.0 Connector N/A USB devices connection
9 NVMe 4 x 3.5” disk bays for faster hybrid storage performance.
❶
❷
❸
❹
❺
❻
❼
❽
❼
9
9
9
9

8
1.2.2 Rear anel Configuration
No.
Name Description
1 Power Module 1 Default primary power supply module.
2 Power Module 2 Backup power supply module.
3 System I/O
(Depends on M/B Specifications)
he I/O shield should come with the motherboard or
provided by motherboard vendors.
4 7 Low Profile PCI-E Slots he slots support low profile cards. he bracket should
be removed before using.
5 OS HDD
his slot is for InWin OS disk backup module (optional),
which supports two 2.5” 12G SSDs and features hot-
swap function.
❶
❷
❸
❹
❺

9
2Hardware Installation
2.1 Removing and Installing a Hard Drive
he IW-RS212-07 features tool-less trays. Users no longer need to use screws to mount
disks, and can swap drives faster.
2.1.1 Installing a Hard Drive
Step 1: Press the release button then pull the handle outward.
Step 2: Pull both sides of the 3.5” HDD tray outward.
Place the hard drive into the tray.
Push both sides of 3.5” HDD tray back.
Step 3: Insert the HDD tray to the slot.
Step 4: Push back the lever until it clicks.
Step 1
Step 2
Step 3 Step 4
Press
Pull
Insert the HDD tray
Push back

10
2.1.2 Removing a Hard Drive
Step 1: Press the release button then pull the handle outward.
Step 2: Pull both sides of 3.5” HDD tray outward.
Pull out the hard drive.
Push both sides of 3.5” HDD tray back.
Step 3: Insert the HDD tray to the slot.
Step 4: Push back the lever until it clicks.
Step 1
Step 2
Step 3
Step 4
Pull
Press
Insert the HDD tray
Push back

11
2.2 Removing and Installing the Top Cover
Step 1: Release the screw in the rear of the top cover, a nd push the silver buttons on
both sides up.
Step 2: Push the rear top cover backward.
Step 3: o insert the cover, place the cover at the rear and push it to the fitted location.
ighten the screw to secure the rear cover. (Refer to steps 1-2 above.)
Step 1
Step 2
Push
Push
Release
1
Push
2

12
2.3 Removing and Installing the Fan Module
he IW-RS212-07’s built-in fan modules feature a tool-less design, which makes it easy
to maintain.
2.3.1 Removing the Fan Module
Step 1: Pull the handles up on both sides of the fan.
Step 2: Pull out the fan module from the fan slot.
Step 1
Step 2
Press
Press
Pull
Pull

13
2.3.2 Installing the Fan Module
Step 1: Hold and put the fan module into the fan slot.
Step 2: Connect the fan to the motherboard.
Step 1 Step 2
2.4 Removing and Installing the SU Module
he IW-RS212-07 has a built-in redundant power supply unit. With this function, the
system is capable of still operating if one of the modules fail. o replace it, the user only
needs to release the failed module, then insert a functional module.
2.4.1 Removing the SU Module
Step 1: Press the release tab of the power supply unit’s module at the back.
Step 2: Pull the module out using the handle.
Step 1

14
Step 2
Pull

15
2.4.2 Installing the SU Module
Step 1: Make sure the label is facing upward, and push the power supply module
into the cage until you hear a click.
NOTE: 1. The un t supports InW n PSU modules only, please do not attempt to nsert any
other brands of modules.
2. The two PSU modules’ output wattage must be the same.
2.5 Removing and Installing the Rear 2.5” HDD For OS:
his slot is for the InWin OS disk backup module (optional), which supports two 2.5” 12G
SSDs and features hot-swap function.
2.5.1 Removing the Rear 2.5” HDD:
Step 1: Press the release button then pull the handle outward.
Step 2: Pull out the hard drive.
Step 3: Insert the HDD tray to the slot.
Push back the lever until it clicks.
Step 1
Push
Press
Pull
Press

16
Step 2
Step 3
2.5.2 Installing the Rear 2.5” HDD:
Step 1: Press the release button then pull the handle outward.
Step 2: Place the hard drive into the tray.
Step 3: Insert the HDD tray to the slot.
Push back the lever until it clicks.
Step 1
Step 2
Push
Press
Pull

17
Step 3
2.6 Installing the Slide Rail
he IW-RS212-07 is a rackmount model, which support EIA-RS310D standard cabinets
and chassis racks. InWin provides standard slide rails to allow users to mount the chassis
onto cabinets.
2.6.1 Identifying the Slide Rail
he slide rail by your order might be different. You can reference the quick
installation guide inside the slide rail package and follow the instructions to mount
the rail onto your cabinet or chassis rack.
2.6.2 Removing the Inner Rail and Sliding the Intermediate Rail Back
Step 1: Pull out the inner rail until it reaches the stop. Release the blue slide tab to
unlock.
Step 2: Continue pulling the inner rail until the second stops. Release the white
slide tab to remove the inner rail.
Step 3: Pull the latch on the middle rail upward and retract the middle rail back.
Step 1 ~ 2
Step 3
Push