InWin IW-RF100S User manual

IW-RF100S
User’s Manual

- 1 -
Table of Content
PREFACE P.2
SAFETY INFORMATION P.2
SPECIFICATIONS P.4
1Product Introduction
1.1 Box Content P.5
1.2 General Information P.6
1.2.1 Front Panel Controls and Indicators P.7
1.2.2 Rear Panel Configuration P.8
2Hardware Installation
2.1 Removing and Installing a Hard Drive P.9
2.1.1 Installing a Hard Drive P.9
2.1.2 Removing a Hard Drive P.9
2.2 Removing and Installing Top Cover P.10
2.3 Removing and Installing a Fan Module P.11
2.3.1 Removing a Fan Module P.11
2.3.2 Installing a Fan Module P.11
2.4 Removing and Installing a PSU Module P.12
2.4.1 Removing a PSU Module P.12
2.4.2 Installing a PSU Module P.13
2.5 Installing Slide Rail P.13
2.5.1 Identifying the slide Rail P.13
2.5.2 Take out the inner rail and slide the intermediate rail back P.13
2.5.3 Attach the inner rail to the chassis P.14
2.5.4 Mount the rail bracket to the cabinet P.14
2.5.5 Insert the chassis to the cabinet P.15
2.6 Installing Motherboard P.16
2.7 Connecting Cable P.17
3Backplane Introduction P.18
4Compatibility Lists P.20
5Q&A P.20
6Technical Support P.23

- 2 -
PREFACE
Thank you for choosing In Win IW-RF100S. This manual is written for system technicians who are
responsible for installation, troubleshooting, managing, and repairing this server chassis. This
document provides the overview of all the features of the chassis, a list of accessories or other
components you may need to finish the installation, troubleshooting methods, and instructions of
adding and removing components on the In Win IW- RF100S. For the latest version of this manual, you
may visit In Win’s server website to download the latest updated version.
SAFETY INFORMATION
To ensure safe and smooth operation of your In Win IW- RF100S, it is essential that you choose an
appropriate location for the system, provide an appropriate operating environment, and adequate
power for all components of the system. As you plan for installation, follow the guidelines below to
ensure that the system and its environment are safely and appropriately positioned for efficient
operation and service. Your system should be installed and serviced only by technically qualified
persons.
Environment selection: The system is designed to operate in a typical office environment. The location
should be a clean, dry, and free of airborne particles; a well-ventilated room and away from sources of
heat including direct sunlight and radiators; it should keep the sources of vibration or physical shock
away; the space should be with a properly grounded wall outlet, and with sufficient space to access the
power supply cords. The operation environment temperature should be around 0°C to 40°C (32°F to
104°F).
Heed safety instructions: Before working with In Win IPC/Storage server/ System products, we strongly
recommend you are using this guide as a reference and follow the safety instructions. The instructions
in this manual will help you ensure and maintain compliance with existing product certifications and
approvals. Follow the described, regulated components mentioned in this manual. Use of non UL
listing products or other regulatory did not approvals will make non-compliance with product
regulations in the region(s) in which the product is sold.
System power on/off: The power button DOES NOT totally turn off the system AC power. To remove
the power of system, you have to unplug the AC power cord from the outlet or system’s power supply
units. Make sure the power cord is unplugged before you open the chassis, add, or remove any
components.

- 3 -
Hazardous conditions, devices and cables: Hazardous electrical conditions usually present on power
supply units, and communication cables. Disconnect the power cord, and any other device which
attached to the server before opening the case. Otherwise, it will raise the risk of personal injury or
equipment damage.
Electrostatic discharge (ESD) and ESD protection: In most cases, ESD damages disk drives, electronic
boards, and other parts. We recommend that you work the installation only at an ESD free space. If the
situation does not allow, perform ESD protection actions by wearing an anti-static wrist strap attached
to ground any unpainted metal surface on your server during your operation.
Installing or removing jumpers: A jumper is a short length of conductor used to close, open or bypass
part of an electronic circuit. Jumpers on In Win backplane have a small tab on top that you can pick up
with your fingertips. Grip the jumper carefully, and plug the jumper to cover the jumper pins on the
backplane. Once you need to remove the jumper, gripping the jumper, and carefully pull out without
squeezing.
CAUTION
To avoid damage and prove your safety, please notice and following the terms listed below:
1. No to populate hard drives and turn on the power before the system is settle down.
2. Tighten or loosen all the screws, please use screw driver to operate.
3. Apply the correct screws which packed in the accessories box.
4. For your safety, it requires at least two persons lift, and place the unit.
5. Before mounting the unit to the cabinet, make sure the rail is installed correctly.
6. When installing and removing any module or parts, please operate by the handles.

- 4 -
SPECIFICATIONS
Model Name
IW-RF100S
Standard
EIA-RS310D
M/B Form Factor
MINI ITX (6.7“ x 6.7“)
Dimensions (D x W x H)
250 x 482.6 x 44 mm (9.8“ x 19” x 1.75”)
Drive Bay
Internal: 2.5" HDD x 2
3.5” HDD x 2 (Optional 2.5” HDD x 4)
Power Supply
Supports
▪Form Factor: Flex
▪Watt: Single 265W, or 315W
Indicator
Power Status, HDD, LAN Activity LEDs,
Front Control Panel
Power Switch, System Reset, USB 3.0 x 2
Cooling Fan
Supports 40 x 28 mm PWM Easy-Swap Fan x 2 (Max up to 3)
Material
Material: SGCC
Thickness: 1.0 mm
Slide Rail
20" Friction slide rail

- 5 -
1Product Introduction
1.1 Box Content
When you open the carton box of IW-RF100S, the contents should include:

- 6 -
1.2 General Information
When you open the top cover should be like the diagram shows bellow.
Top cover
Single module
power supply
PWM Fan x 2pcs
(max to 3 pcs)
Mini-ITX or ATX
M/B
Front Controls
and indicators
2 x 3.5” HDD tray

- 7 -
1.2.1 Front Panel Controls and Indicators
The front control panel includes USB IO ports and indicator LED lights.
No.
Name
Color
Status
Description
1
USB3.0 Connector
No LED function
USB devices connection
2
Power ON/OFF Button
Blue
Solid on
System is powered on
Off
System is not powered on
3
Power LED
No LED function
Press the button to activate Power LED
4
Hard Disk LED
Green
Blinking
System HDD accessing
5
Reset Button
No LED function
System reset
6
LAN LED
Amber
Blinking
Link between system and network
Off
No date transmission or receiving is occurring
3
2
4
6
5
1

- 8 -
1.2.2 Rear Panel Configuration
The rear side of IW-RF100S contains the space of AC power source, system IO, and an
expansion cards slot.
No.
Name
Description
1
Power Supply Window
This window is for installing single PSU, please reference In-Win
compatibility list to select the compatible models.
2
System I/O (depend on
M/B specification)
The I/O shield is different by brands and models, please contact In Win sales
for custom I/O shield service.
1
2

- 9 -
2Hardware Installation
2.1 Removing and Installing a Hard Drive
In Win IW-RF100S has two 3.5” disk cages, each supports installing a 3.5” hard drive, and stacking
a 2.5” drive.
2.1.1 Installing Hard Drive
Step 1: Loosen the thumb screw and pull backward to remove disk cage.
Step 2: Populate the 2.5” drive on the cage and fix it with 4 screws from the bottom. Stake a
3.5” hard drive on top, and screw it up with 4 screws from both sides.
Step 3: Put back the disk cage to the chassis, and push back the cage to the original position,
then tighten the thumb screw.
Step 1
Step 2
Step 3
Loosen the
thumb screw
a. Install 2.5” HDD x 1pcs
b. Install 3.5” HDD x 1pcs
b
a
Complete the HDD cage and
put it back to the chassis.

- 10 -
2.2 Removing and placing Top Cover
Step 1: Release the screw on the back-end of cover, and pull backward the top cover.
Step 2: Lift the top cover to remove.
To place the top cover, repeat backward the above steps to complete the action.
Step 1 Step 2
2.3 Removing and Installing the fan wall
The fan module of IW-RF100S is tool-less design with easy swap feature. Removing the fan wall
before posting the motherboard to get more space for the processing.
2.3.1 Removing the fan wall
Step 1: Unplug the fans’ power cable and push the plastic tabs to lift the fan modules
Step 2: Unscrew the fan wall bracket to remove
Step 1 Step 2
Pull backward the top
over and remove it.

- 11 -
2.4 Removing and Installing a PSU
In Win IW-RF100S supports single Flex-ATX power supply unit. Users can select power supply
according to the environment’s wattage requirements.
2.4.1 Installing Single PSU
Step 1: Place the PSU to the rear right corner of the chassis and make sure the screw holes
on the rear bracket meet the chassis frame
Step 2: Use 4 screws to fix the power supply unit.
Step 1 Step 2
2.5 Installing a Slide Rail
In Win IW-RF100 is a rackmount model, which support EIA-RS310D standard cabinet and chassis
rack. In Win provides standard slide rail to let users mount the chassis on to the cabinet.
2.5.1 Identifying the sections of the Slide Rail
2.5.2 Installing a Slide Rail
Step 1: Release the inner rail from the slide
Step 2: Mount the inner rails onto the chassis by the direction which the arrows show.

- 12 -
Step 3: Install the outer rails and the brackets onto the rack.
2.5.3 Mount the chassis onto the cabinet
Step1: Make sure the ball bearing retainer is at the forefront.
Step2: Insert the inner rail to the outer rail which has already locked up on the cabinet.
Step3: Mount the inner rail onto the chassis by the direction which the arrows show on the
image.
Step4: Step4: Use 2 M6 screws to fix the handle bracket on the rack.
2.6 Installing Motherboard
Before installing the motherboard, preparing the IO shield for your motherboard, and mount it to
the system IO window 1.2.2 shows. If you cannot find the IO shield, please check with your
motherboard vendor, or contact In Win for IO shield production service.
Step 1: Measure the motherboard location and removing the plastic dots to appear the holes.
Step 2: Install the steel pillars, which you can find in the accessories box to the holes matching
the motherboard’s mounting holes, you may use a flathead screw driver.
Step 3: Place the motherboard down to the chassis, and make sure the pillars’ threaded holes are
matching the mounting holes on the motherboard.

- 13 -
Step 4: Use hex screws from the accessories box to fix the motherboard in the chassis.
2.7 Connection Cable
2.2.1 Connecting LED cable, front control panel and front USB IO ports
As 1.2.1 descripts, In Win IW-RF100S built-in a set of front control panel and USB access
ports. You need to connect to the pins on the motherboard to active the functions. The pin
function and location you can find from your motherboard’s user guide.
※ If the motherboard’s led power source is 3-pin type, please use the 2Pin-to 3Pin convertor form
the accessory box to connect.
No.
Connector Name
Color
Front IO Indication
P2
Power Switch
White/Black
Power ON/OFF Button with LED
P3
Power LED※
White/Purple
Power ON/OFF Button with LED
P4
HDD LED
White/Blue
HDD Active LED
P5
LAN LED 1
White/Green
LAN LED
P6
LAN LED 2
White/Yellow
LAN LED
P7
Reset
White/Orange
System Reset
USB
USB 3.0 Connector
Flat Black
USB 3.0
USB 3.0
LED Connector

- 14 -
2.8 Reverser IO
IW-RF100S features IO interface direction reversible, which allows user turn the IO to the front
and deploy the appliance easily. It only needs to take few steps to change the factory default rear
IO access to front IO access.
Step 1: Remove the top cover.
Step 2: Unload the power supply unit and unscrew the control panel module; switch the position.
Step 3: Unscrew to remove the fan wall, reverse to change the airflow direction.
Step 4: Remove the handle of both sides, and mount on the opposite end to let the handle face
the rear side.
3Compatibility Lists
To reach best performance and avoid system failure, In Win strongly recommend users choosing the
components from In Win’s compatibility list. All the components are tested in In Win’s lab and assured
the components are working well with In Win’s chassis.
You can download the latest updated device compatibility list from In Win’s website:
https://www.in-win.com/en/ipc-server
4Q&A
1. Is it possible to add front cover?
You may adapt IW-RS104-02M’s 1U front cover, but it will block the USB ports and lights in rear access,
and block the IO ports in front access mode, which is not realistic.
2. Do the chassis support mirrored OS disks?
You can mirror any two hard drives, such as IW-RF100’s two 2.5” hard drives, or IW-RF100S’ two 3.5”
and two 2.5” drives. Yet, the disk mirroring is defined by your motherboard or your RAID 1 controller
card. You may check the vendor’s guide to mirror your OS disks.
3. Can it support form factor MB such as M-ATX?
In Win IW-RF100 supports motherboard range from Mini-ITX to ATX. Unless you would like to mount a
customized motherboard which is not meet Intel’s standard, you will need to contact In Win partners
or sales for customization service.