InWin IW-RJ448-05 User manual

IW-RJ448-05
User Manual

Table of Contents
PREFACE .......................................................................................................................................1
SAFETY INFORMATION .................................................................................................................1
CAUTION ......................................................................................................................................2
SPECIFICATIONS............................................................................................................................3
1Product Introduction.............................................................................................................4
1.1 Box Contents ............................................................................................................................4
1.2 General Information .................................................................................................................5
1.2.1 Front Panel Controls and Indicators ......................................................................................................... 6
1.2.2 Rear Panel Configuration.......................................................................................................................... 7
1.2.2.1 Expander (Host) Configuration................................................................................................................. 8
2Hardware Installation...........................................................................................................9
2.1 Removing and Installing a Hard Drive........................................................................................9
2.1.1 Open the HDD Drawer .............................................................................................................................. 9
2.1.2 Close the HDD Drawer .............................................................................................................................. 9
2.1.3 Installing a Hard Drive .............................................................................................................................. 9
2.1.4 Removing a Hard Drive ........................................................................................................................... 11
2.2 Removing and Installing the Fan Module.................................................................................11
2.2.1 Removing the Fan Module ..................................................................................................................... 11
2.2.2 Installing the Fan Module....................................................................................................................... 12
2.3 Removing and Installing the PSU+FAN Module........................................................................13
2.3.1 Removing the PSU+FAN Module ............................................................................................................ 13
2.3.2 Installing the PSU+FAN Module.............................................................................................................. 13
2.4Removing and Installing the Host & Disk Expander Module ....................................................14
2.4.1 Removing the Host Expander Module ................................................................................................... 14
2.4.2 Installing the Host Expander Module..................................................................................................... 15
2.4.3 Removing the Disk Expander Module.................................................................................................... 15
2.4.4 Installing the Disk Expander Module ..................................................................................................... 17
2.5 Rail Installation.......................................................................................................................18
2.5.1 The Type of Rail Kit ................................................................................................................................. 18
2.5.2 Fixed Rail Blade....................................................................................................................................... 18
2.5.2.1 Installing the Fixed Rail Blade to the Rack ............................................................................................. 18
2.5.2.2 Insert the Enclosure to the Rack............................................................................................................. 18

3Expander Board Introduction (Host & Disk).........................................................................21
3.1 Expander Board (Host)............................................................................................................21
3.2 Expander Board (Disk) ............................................................................................................22
4User Interface Introduction ................................................................................................. 23
4.1 Overview ................................................................................................................................23
4.2 Key Features ...........................................................................................................................23
4.3 Software Management ...........................................................................................................24
4.3.1 System Management Structure.............................................................................................................. 24
4.3.2 Serial Port Management......................................................................................................................... 25
4.3.3 Network Management ........................................................................................................................... 28
4.3.4 Version Information................................................................................................................................ 34
4.3.5 System Status.......................................................................................................................................... 35
4.3.6 Network Settings .................................................................................................................................... 37
4.3.7 Disk Information ..................................................................................................................................... 38
4.3.8 Zone Setting ............................................................................................................................................ 39
4.3.9 Firmware Upgrade .................................................................................................................................. 42
4.3.10 Web Console ........................................................................................................................................... 48
4.3.11 Advanced Configuration ......................................................................................................................... 49
4.4 Appendix A .............................................................................................................................52
4.5 Appendix B .............................................................................................................................52
5Compatibility Lists .............................................................................................................. 54
6Technical Support................................................................................................................54

1
PREFACE
Thank you for choosing the InWin IW-RJ448-05. This manual is written for system technicians who
are responsible for installation, troubleshooting, managing and repairing this server chassis. This
document provides the overview of all the features of the chassis, a list of accessories or other
components you may need to finish the installation, troubleshooting methods and instructions on
adding and removing components on the InWin IW-RJ448-05. For the latest version of this manual,
you may visit InWin’s server website to download the latest updated version.
SAFETY INFORMATION
To ensure a safe and smooth operation of your InWin IW-RJ448-05, it is essential that you choose
an appropriate location for the system, provide an appropriate operating environment and supply
an adequate amount power for all components of the system. As you plan for installation, follow
the guidelines below to ensure that the system and its environment are safely and appropriately
positioned for efficient operation and service. Your system should be installed and serviced only by
a qualified technician.
Environment selection: The system is designed to operate in a typical office environment:
• The location should be clean, dry and free of airborne particles.
• It should be situated in a well-ventilated room, and away from sources of heat including direct
sunlight and radiators.
• It should be kept away from sources of vibration or physical shock.
• The space should be accommodated with a properly grounded wall outlet, and with sufficient
space to access the power supply cords.
• The operating environment temperature should be around 0°C to 40°C (32°F to 104°F).
Heed safety instructions: Before working with InWin IPC/Storage server products, we strongly
recommend you use this guide as a reference and follow the safety instructions. The instructions in
this manual will help you ensure and maintain compliance with existing product certifications and
approvals. Follow the described, regulated components mentioned in this manual. Use of non-UL
listing products or other regulators may not comply with product regulations in the region(s) in
which the product is sold.
System power on/off: The power button DOES NOT totally turn off the system AC power. To
remove the power of the system, you must unplug the AC power cord from the outlet or the
system’s power supply units. Make sure the power cord is unplugged before you open the chassis
or add/remove any components.
Hazardous conditions, devices and cables: Hazardous electrical conditions can be present on/in
power supply units and their cables. Disconnect the power cord and any other device attached to
the server before opening the case. Failing to follow safety procedures will increase the risk of
personal injury or equipment damage.

2
Electrostatic discharge (ESD) and ESD protection: In most cases, ESD may damage disk drives,
electronic boards and other parts. We recommend that you conduct installation only at an ESD
free space. If not possible, perform ESD protection protocol by wearing an anti-static wrist straps
attached to the ground on any unpainted metal surface on your server during operation.
Installing or removing jumpers: A jumper is a short length conductor used to close, open or bypass
part of an electronic circuit. Jumpers on InWin backplanes have a small tab on top that you can
pick up with your fingertips. Grip the jumper carefully and plug the jumper to cover the jumper
pins on the backplane. Once you need to remove the jumper, grip the jumper and carefully pull
without squeezing.
CAUTION
To avoid damage and maintain your safety, please read the following terms listed below:
1. Do not populate hard drives and turn on the power until the system has
stabilized.
Make sure hard drives and other components are properly connected before
turning on the system.
2. Tighten or loosen all screws with a screwdriver.
3. Apply the correct screws packed in the accessory box.
4. For your safety, please have at least two people lift and place the unit in its
designated area.
5. Before mounting the unit to the cabinet, make sure the rail is installed correctly.
6. When installing and removing any module or part, please use the handles.

3
SPECIFICATIONS
Model Name
IW-RJ448-05
Standard
EIA-RS310D
Dimensions (D x W x H)
w/o Front Door
736.6 x 482.6 x 176 mm
(29" x 19" x 7")
Storage
External: Hot-swap 3.5" x 48 (SAS 12Gbps)
Power Supply
(PSU+FAN Modules)
Supports
▪ Form Factor: High efficiency redundant PSU
▪ Watt: 1100W
Cooling Fan
(PSU+FAN Modules)
80 x 38 mm PWM x 6
12G Expander Module
1 or 2
Host/Expansion Port
6 x Mini SAS HD (SFF-8644) for each 12G expander module
Management
Smart fan, thermal monitor, HDD monitor, voltage monitor, alarm
warning
SES
Supports SES-2 (SCSI Enclosure Service)
Maintenance
Supports management by Ethernet (Optional) and RS-232
HDD Power Management
HDD sequential power on
Temperature
0ºC to 35ºC
Material
Material: SGCC
Thickness: 1.6 mm
Rail Kit
Fixed rail blade
* The actual product is subject to change without prior notice. In Win Development Inc. reserves the
right to make any final modifications.

4
1 Product Introduction
1.1 Box Contents

5
1.2 General Information
Designed for high scalability and high availability in storage applications, the IW-RJ448-05 JBOD
enclosure is a high density 4U rackmount storage chassis with 48 tool-less bays. It features dual
hot-swap SAS 12G expander modules, six Mini-SAS HD (SFF-8644) for each 12G expander
module, six PSU +Fan module fans, dual redundant 1100W power + fan module, and GUI
supports via Ethernet board (Optional).

6
1.2.1 Front Panel Controls and Indicators
The front panel includes control buttons and LED indicators.
No.
Name
Color
Status
Description
1
Power On/Off Button
with LED
Blue
Solid on
System is powered on
N/A
Off
System is off
2
Chassis ID Button with
LED
Blue
Solid on
Press the button to activate chassis
identification
3
Status LED
Red
Solid on
System maintenance (PSU, fan
malfunction)
4
Drives Status LEDs for
Bays 1-48
Follow the
table below
5
Drawer Lock
6
Drawer Thumbs Screw
7
Drawer Handle
Status LED:
System Healthy
System Maintenance (PSU, fan malfunction)
Drive Status LED:
(Solid) Drive Online
(Solid) RAID Drive
(Blink) Drive Activity
(Blinking Purple on Solid Blue) RAID Active / Rebuild
(Solid) Drive Failed
(Alternating Blink) Drive Faulty / RAID Failure
(Blink) Drive Missing
(Blink) Drive Locate
Drive Offline / Removed
1
2
3
4
5
6
6
7
7

7
1.2.2 Rear Panel Configuration
No.
Item
No.
Item
1
Power Module 1 (PSU+FAN Module)
8
Fan Module 6 (PSU+FAN Module)
2
Power Module 2 (PSU+FAN Module)
9
Primary Expander Module
3
Fan Module 1 (PSU+FAN Module)
10
Secondary Expander Module
4
Fan Module 2 (PSU+FAN Module)
11
Power Module Handle
5
Fan Module 3 (PSU+FAN Module)
12
Power Switch
6
Fan Module 4 (PSU+FAN Module)
13
PSU Alarm Mute Button
7
Fan Module 5 (PSU+FAN Module)
14
PSU Status LED
PSU Status LED:
Power Standby
Power On
Loss of Power
3
5
7
4
6
8
9
10
2
1
11
12
13
12
14
14
11

8
1.2.2.1 Expander (Host) Configuration
No.
Name
Description
1
SAS Port LEDs
Host HBA/RAID card connection
2
SAS Host Ports
External Uplink, Connect to HBA/RAID card
3
SAS Expansion Ports
External Downlink, Connect to cascading JBOD
4
Expander Module Status LED
Heartbeat
5
ID LED / Button
Press the button to activate chassis identification
6
Expander Serial Port (RS-232)
RS-232 Support
7
Network Management Port
Connect to Ethernet remote monitoring
8
Expander Module Handle
SAS Port LEDs:
Expander Module Status LED:
ID LED:
SAS Connection On
Heartbeat
ID on
SAS Activity
4
7
5
6
2
3
1
8

9
2 Hardware Installation
2.1 Removing and Installing a Hard Drive
The IW-RJ448-05 JBOD features tool-less trays, users can easily swap drives without any
screws.
NOTE: Do not leave the HDD drawer open for more than 1 minute to prevent overheating.
2.1.1 Open the HDD Drawer
Step 1: Loosen the keylock and the thumbscrews of the drawer.
Step 2: Pull the HDD drawer outward.
Step 1:
Step 2:
2.1.2 Close the HDD Drawer
Step 1: Push the drawer back.
Step 2: Lock the keylock and tighten the thumbscrews.
Step 1:
Step 2:
2.1.3 Installing a Hard Drive
Step 1: Release the latch in the direction of the arrow on the tray.
Open the disk tray cover and pull it outward as a handle.
Step 2: Pull up the tray until it clicks.
Step 3: Fully insert the HDD into the tray from the correct disk port orientation.
Pull
Push

10
Step 4: Align the HDD screw holes and plug in the pins on the side of the tray.
Keep the tray pins against the HDD screw holes and push the disk tray back
to the location.
Step 5: Release the latch to close the cover to lock.
Step 1:
Step 2 Step 3
Step 4
Step 5
Push
Pull
Push
Press
Press
Push
Press
Push
Push

11
2.1.4 Removing a Hard Drive
Step 1: Release the latch in the direction of the arrow on the tray.
Open the disk tray cover and pull it outward as a handle.
Step 2: Pull up the tray until it clicks.
Step 3: Pull the hard drive out carefully.
Step 4: Lower the disk tray back. Release the latch to close the cover to lock.
Step 1
Step 2 Step 3
Step 4
2.2 Removing and Installing the Fan Module
The IW-RJ448-05 JBOD has built-in fan modules that support hot-swappable and
redundant features, which are easy to maintain with the tool-less design.
2.2.1 Removing the Fan Module
Pull
Pull
Push
Push
Push

12
Step 1: Loosen the thumbscrew of the fan module.
Step 2: Press the handle and pull out the fan module with the slot to separate it
from the PSU+FAN module.
Step 1
Step 2
2.2.2 Installing the Fan Module
Step 1: Push the fan module back into the slot until it clicks.
Step 2: Secure the thumbscrews in place and tighten.
Step 3: Connect the fan to the backplane.
Step 1
Step 2
Pull
Push

13
2.3 Removing and Installing the PSU+FAN Module
The IW-RJ448-05 hosts dual built-in redundant 1100W PSU+FAN modules. Each module
cage contains one 1100W power supply and three fan modules. With this function, the
system is capable of still functioning if one of the modules fail. To replace it, the user
only needs to release the failed module, then insert a functional module.
NOTE: The two PSU modules’ output wattage must be the same.
To ensure the stability of use, if the PSU module fails, it is recommended to replace
the PSU with the fan modules together.
2.3.1 Removing the PSU+FAN Module
Step 1: Loosen the thumbscrew of the PSU+FAN module cage at the back.
Step 2: Push down the handle and use the handle to pull out the cage. Separate
the PSU+FAN module from the enclosure.
Step 1
Step 2
2.3.2 Installing the PSU+FAN Module
Step 1: Push the 1100W PSU+FAN module into the cage until it clicks back the
original location.
Step 2: Tighten the thumbscrew to secure the cage.
Push
Pull
PSU
Fan

14
Step 1
Step 2
2.4 Removing and Installing the Host & Disk Expander Module
The IW-RJ448-05 JBOD is accommodated with pre-installed dual redundant host
expander and four redundant disk expander modules. The internal expander is primary,
and the external expander will be the secondary. The host expander module includes an
Ethernet management module, which allows users to monitor and maintain the system.
Also, the redundant module can minimize downtime should any of the expanders fail.
2.4.1 Removing the Host Expander Module
Step 1: Loosen the thumbscrew of the host expander module.
Step 2: Rotate the expander module lever outward.
Step 3: Pull out the expander module.
Step 1
Push
PSU
Fan

15
Step 2 Step 3
2.4.2 Installing the Host Expander Module
Step 1: Push the expander module into the cage until it clicks back to the original
location.
Step 2: Rotate the lever back into position.
Step 3: Tighten the thumbscrew.
Step 1
Step 2
Step 3
2.4.3 Removing the Disk Expander Module
NOTE: Do not leave the HDD drawer open for more than 1 minute to prevent
overheating.
Step 1: Open the HDD drawer. (Please refer to 2.1.1)
Step 2: Loosen the thumbscrews and side screws of the enclosure, then remove
the cable management cover.
Step 3: Remove the cable from the disk expander module.
Pull
Push

16
Step 4: Loosen the thumbscrew of the module.
Step 5: Rotate the disk expander module handle outward.
Step 6: Pull out the disk expander module.
Step 2
Step 3
Step 4
Step 5
Step 6
Unplug
the Cables
Pull

17
2.4.4 Installing the Disk Expander Module
NOTE: Do not leave the HDD drawer open for more than 1 minute to prevent
overheating.
Step 1: Place the disk expander module into the cage until it clicks.
Step 2: Align the thumbscrew into position and tighten the thumbscrew.
Step 3: Connect the cable to the disk expander module.
Step 4: Push the cable management cover back to original position.
Tighten the thumbscrews and side screws of the enclosure.
Step 5: Close the HDD drawer. (Please refer to 2.1.2)
Step 1
Step 2
Step 3
Step 4
Push
Connects
the Cables
Push