IQAir CleanZone 3030 series User manual

ABSOLUT SERIES
™
ABSOLUT 3000
Air Purification System
™
ABSOLUT
Air Purification System
™
Unloading and Loading
the CleanZone 3030
0906

TABLE OF CONTENTS
UNLOADING THE IQAIR
CLEANZONE 3030
LOADING THE IQAIR
CLEANZONE 3030
Unloading and Loading the CleanZone 1
Opening the crate ………………………………………………………………………………………. . . page 3
Preparing the loading ramp ……………………………………………………………………………... page 3
Guide the CleanZone down the ramp …………………………………………………………………. . . page 4
Fold back the ramp ………………………………………………………………………………………. page 4
Opening the crate………………………………………………………………………………………... page 6
Preparing the loading ramp ……………………………………………………………………………... page 6
Guide the CleanZone into the ramp …………………………………………………………………….. page 7
Foling back the ramp…………………………………………………………………………………….. . page 8
Closing the crate………………………………………………………………………………………….. page 8

2
3
1
UNLOADING THE IQAIR CLEANZONE 3030
Begin by removing the door of the crate.The front of the door is
marked with a red arrow that indicates the top and the outer panel
of the door. Remove the 4 screws that run horizontally down the
left and right sides of the door. Together there are a total of 8
screws – each is marked by a red circle.
Once the screws have been taken out, carefully remove the front
door and lean it against the side of the crate.
(Note: keep door, screws, etc., for future return shipping.)
Next, the loading ramp must be put down. Remove the center
screw that secures the loading ramp to the base of the crate.
Unfold the ramp and extend it to the floor, as is shown in the next
2 photos. Open and extend the loading ramp to the floor.
Unloading the CleanZone 3

5
6
4
Next, carefully roll the CleanZone unit out of the crate and down
the ramp. Because the CleanZone unit weighs 200 lbs., the unit
should be maneuvered using two people.
This is how the loading ramp looks
when extended to the floor.
Open and extend the loading ramp
to the floor.
Unloading the CleanZone 4

8
7
Next, fold the loading ramp back up and re-insert the 2 _ inch
screw into the center. This secures the loading ramp to the base of
the crate while in storage.
Please keep the IQAir crate and components for future transport. Refer to Part 2: Loading the CleanZone 3030, when
ready to return the unit to IQAir.
Should you require assistance, please feel free to contact the IQAir Solution Center at 877-715-4-AIR (247).
Thank you for choosing IQAir!
Carefully tilt the CleanZone and
guide it down the ramp. The unit is
mounted on wheels for easy move-
ment. Because of the snug fit inside
the crate, be careful that all cords to
the CleanZone remain secure (cords
run up the left side of unit into the
open duct on top.)
Unloading the CleanZone 5

2
3
1
LOADING THE IQAIR CLEANZONE 3030
Begin by removing the door of the crate. The front of the door is
marked with a red arrow that indicates the top of the door and
the outer panel. Remove the 4 screws that run horizontally down
the left and right sides of the door. Together there are a total of
8 screws – each is marked by a red circle.
Once the screws have been taken out, carefully remove the front
door and lean it against the side of the crate.
(Note: keep door, screws, etc., aside for later use.)
Next, the loading ramp must be put down. Remove the center
screw that secures the loading ramp to the base of the crate.
Unfold the ramp and extend it to the floor, as is shown in the next
2 photos.
Open and extend the loading ramp
to the floor.
Loading the CleanZone 6

5
6
4
Secure all cords neatly inside the top module. Run the cords from
the Motor Module along side the CleanZone and place the excess
length into the top opening.Because of the snug fit inside the
crate, it is important to have all cords straight with no slack in
them.
Next, carefully tilt the CleanZone and gently push it up the ramp
into the crate. The wheels should be straight and aligned directly
under the unit.
Next, roll the CleanZone up to the crate’s loading ramp. Position
the unit so that the bottom duct opening is facing outwards.
Because the CleanZone unit weighs 200 lbs., it should be maneu-
vered using two people.
This is how the ramp looks when
extended to the floor.
Loading the CleanZone 7

8
9
7
Next, fold the loading ramp back up and re-insert the 2 _ inch
screw into the center.
This secures the loading ramp to the base of the crate.
Next, secure the front door for shipping. Make sure the door is per-
fectly aligned on both sides of the crate. Then re-insert the eight
(8) screws in the designated areas on the door (4 each down the
left and right sides, marked in red). If the original areas marked in
red are damaged,place the screw above or below the original hole,
but do not place the screw to the left or right side of the original
hole.Doing so may cause damage to the crate.
To UNLOAD the CleanZone,please refer to Part 1: Unloading the CleanZone 3030.
Should you require assistance, please feel free to contact the IQAir Solution Center at 877-715-4-AIR (247).
Thank you for choosing IQAir!
Position the CleanZone all the way to the back of the crate.
This is how the unit should look once inside the crate.
Loading the CleanZone 8