IQAir HealthPro Compact User manual

User Manual
HealthPro® Compact
Swiss Made

Important Safety Instructions
105.10.10.12 / 091216
About This User Manual
Congratulations on your purchase of this IQAir high-performance air cleaning system. Please study this user manual
carefully to familiarize yourself with the special features and functions of your IQAir system and keep it in a safe place
for future reference.
Read these instructions before using the air cleaner:
•Do not use this air cleaner as sole protection against harmful pollutants.
•Do not immerse the air cleaner in water or other liquids.
•Always disconnect the power from this air cleaner by unplugging the power cable before adding or removing
parts and before cleaning.
•Do not operate this air cleaner if it has a damaged cord or plug, if the motor fan fails to rotate, if it is not working
properly, if it has been dropped or damaged, or dropped into water.
•If the power cord of this air cleaner should become damaged, it may be replaced with a similar two-pole cord, as
is commonly used for computers and similar air cleaners.
•Only use this air cleaner for its intended purpose of air cleaning in non-industrial environments.
•Do not use this air cleaner in areas with very high concentrations of dust or powder to prevent the danger of dust
explosions.
•Do not use this air cleaner in explosive areas.
•Do not use attachments or lters not recommended by IQAir.
•Do not use outdoors.
•Do not obstruct the air inlet and air outlet of the air cleaner.
•Do not place the air cleaner on a soft surface such as a bed or other soft furnishings.
•Only use this air cleaner in an upright position.
•Do not place next to a humidier.
•Keep the power cord away from heated surfaces.
•Save these instructions for future reference.
The IQAir Group reserves the right to change specifications contained in this document at any time and without prior notice.
© 2002-2010 The IQAir Group. All rights reserved. IQAir, HealthPro and HyperHEPA are the registered trademarks of The IQAir Group. V5-Cell, PreMax and
EvenFlow are trademarks of The IQAir Group. IQAir systems and filters are protected under U.S. patents 6 001 145 and 6 159 260. Other U.S.,
European and Asian patents pending.
2

Table of Contents
Page
Important Safety Instructions 1
Chapter 1 – Air Cleaning Systems and Indoor Air Quality 4
1. 1 Improving Indoor Air Quality 4
Chapter 2 – Setting Up 5
2. 1 Unpacking 5
2. 2 Choosing a Suitable Location 6
2. 3 Connecting to Power 6
2. 4 Fitting and Removing Casters 7
Chapter 3 – The IQAir® System’s Components 9
3. 1 Description of Housing Components 9
3. 2 Description of Removable Components 10
3. 3 How the IQAir System Works 10
Chapter 4 – Using the Control Panel 11
4. 1 Description of Control Panel 11
4. 1. 1 Description of Control Panel Keys 11
4. 2 Control Panel Locking Function 12
4. 3 Fan Speed and Air Delivery 12
4. 3. 1 Regulating Fan Speed 12
4. 3. 2 Air Exchange Rates in Differently Sized Rooms 13
4. 4 Using the Menu Functions 13
4. 4. 1 Menu Overview 13
4. 4. 2 Filter Life Monitor 14
4. 4. 3 Setting the Auto Timer 15
4. 4. 4 Day-of-the-Week Timer 16
4. 4. 5 Timer ON/OFF Fan Speed Selection Menu 16
4. 4. 6 Timer Information in the Control Panel 17
4. 4. 7 Time & Day Setting 18
4. 4. 8 Filter Life Reset (New Filter) 18
4. 4. 9 Changing the Airflow Units 19
4. 4. 10 Language Setting 19
Chapter 5 – Using the Remote Control 20
5. 1 Description of Remote Control Elements and Functions 20
5. 2 Getting the Best Transmission Results 20
5. 3 Replacing the Remote Control Battery 21
Chapter 6 – Replacing Filters 21
6. 1 Location of the Filters 21
6. 2 Ordering Replacement Filters 21
6. 3 Opening and Closing the Housing 22
6. 3. 1 Troubleshooting When Closing the Housing 22
6. 4 Replacing the Pre-Filter (Filter 1) 22
6. 5 Replacing the HyperHEPA Filter (Filter 2) 24
6. 6 Discarding Used Filters 24
Chapter 7 – Maintenance 24
7. 1 Cleaning the Housing 24
7. 2 Maintenance-Free Fan 24
7.3 Technical Support and Repairs 25
7.4 IQAir Warranty 25
Chapter 8 – IQAir® Optional Accessories 25
Technical Specifications 26

Chapter 1 – Air Cleaning Systems and Indoor Air Quality
4
Chapter 1 – Air Cleaning Systems and Indoor Air Quality
1.1 Improving Indoor Air Quality
Air cleaning can play an important role when it comes to improving indoor air quality. However, it should be noted
that air cleaning should be used in conjunction with pollution source control and ventilation, wherever possible.
Strategy to improve indoor air quality
To tackle any indoor air quality problem, keep the following three-step strategy in mind:
1. Eliminate or reduce the air pollution source as much as possible. Source control is by far the most effective way to
improve indoor air quality, since it sets out to deal with air pollution at the point of origin.
2. Ensure that sufcient fresh air is entering the room from outside. Air cleaners are not a substitution for sufcient
ventilation. They are not able to reverse the conversion of oxygen (O2) into carbon dioxide (CO2), caused by
breathing and combustion processes.
3. Ensure the IQAir system can clean enough air to cope with your room size. The actual hourly air volume cleaned
by the system should be at least double the air volume of your room. If the rate at which pollutants enter the room
air is high or the indoor air quality requirements are stringent, the hourly air delivery of the system needs to
exceed the room air volume several times. To achieve that level of air turnover, it may be necessary to employ
more than one IQAir system, or employ an IQAir HVAC filtration system. (Refer to section 4.3.2)
Air Cleaning Results
Although air cleaners may be advertised and sold to be suitable for use in specic indoor environments and to deal
with specic indoor air quality problems, the manufacturer and distributors make no claim as to the specic air
cleaning results that are achieved under the user’s individual operating conditions. The air quality improvements
that can be realized with the IQAir system (as with any air cleaner) in indoor environments depends to a signicant
degree on circumstantial factors which are out of the control of the manufacturer or distributors. Important factors
which will influence the air quality improvements that can be achieved in an indoor environment with an air cleaner
include:
•Type of air pollutants present and their filtration efficiency
•Intensity of the pollutant source(s)
•Pollutant concentration
•Size of the indoor environment (room size)
•Operating speed of the air cleaner
•Number of air cleaners placed in the indoor environment
•Saturation state of the lters in the air cleaner
Consult a qualied specialist to determine an effective and comprehensive indoor air quality strategy.
Caution: Intense concentration of pollutants may cause filters/cartridges to saturate or expire early.

Chapter 2 – Setting Up
5
Chapter 2 – Setting Up
2.1 Unpacking
To unpack the IQAir system, open the top of the box and remove the square styrofoam pad which contains all
accessories and product literature. Lay the box on its side, hold the system by the handle and pull it out of the box.
Remove the plastic bag and foam belt. Keep the packaging for future transport and service needs.
User Manual Certificate of
Performance
I
IQ QAir Air®
®
Cer
Certificate of P tificate of Per erfor formance mance
IQAir Model:
Serial No.:
Shell No.:
I. Air Delivery Rate
Speed 1:
Speed 2:
Speed 3:
Speed 4:
Speed 5:
cfm
cfm
cfm
cfm
cfm
This certifies that the aforementioned air cleaning device has been tested prior to packaging
at the IQAir productionfacility in Switzerland. This particular device has been found to be
in compliance with the model’spublished specifications for air delivery and particle filtra-
tion efficiency.This particular device has passed the particle leakage test.
Speed 1:
Speed 2:
Speed 3:
Speed 4:
Speed 5:
cfm
cfm
cfm
cfm
cfm
Published Air Delivery Actual Air Delivery
180
Speed 6: cfm
240 Speed 6: cfm
HealthPro Compact
TestVoltage/Frequency:
120V / 60 Hz
Page1 of 2
cfm = cubic feet per minute
The aforementioned device
has been tested for its air
delivery at all fan speed set-
tings. Due to component
tolerances, a divergence of
10% + 10 cfm is deemed
acceptable.
Note:
Theair delivery rate refers to
the unit’sinitial air delivery,
which will decrease as filters
load up with dust particles.
Measuring instrument: Alnor LoFlo Balometer.
Instrument accuracy: ± (3% + 2 cfm).
Signed: _________________
Testing& QC Dept.
Testingcarried out by:
1AGUA0000/040603/105600000
150
115
75
45
1AGUA 00 00
QuickStart Guide
Quick-Start Guide: IQAir®HealthPro®Compact Plus
Thank you for choosing an IQAir advancedair cleaning system. This quick-start guide will assist
youin getting started with your IQAir in a matter of minutes. Toaccess some of the more advanced
features of your IQAir system,such as the timer programming, please refer to the user manual.
(Werecommend that you familiarize yourself with the safety instructions in the user manual before first use).
YourIQAir HealthPro system is supplied with the following items:
• User Manual
• Certificate of Performance (individually numberedand hand-signed)
•Warranty/Product Registration Card
• IQAir ReferralProgram Card
• PowerCord, Remote Control (incl.batteries), set of 4 casters
1Setting Up YourIQAir System
A) Unpacking
Tounpack your IQAir system, open the top of the box and remove the user manual,cer tificateof
performanceand the styrofoam pad. Lay the box on its side an pull the IQAir out by its top handle.
Place the system in its upright position and remove all packaging materials.The power cable,
remotecontrol, batteries and set of casters are supplied in a seperate carton contained in the box.
B) Installing the casters
Installing the optional casters is not necessary,however, it may facilitate moving the air cleaner
from room to room. Please refer to the leaflet supplied with the casters for installation
instructions.
C) Choosing a suitable location
The IQAir systemshould be positioned as centrally as possible in the room where the clean air is
desired.
D) Connecting the IQAir system to the power supply
Plug the connector-end of the power cable into the base of the IQAir system.Locate a suitable
wall socket and connect the power cable.The IQAir system is now in standby mode ready to be
switched on.
2Using the Electronic Control Panel
A) Switching the IQAir system on and off
To switch the system on or off,simply press the “power” button, locatedon the far lef t of the
control panel.
B) Regulating the fan speed
Toselec t the desired fan speed,simply press the “arrow”button on the control panel. When the
top speed has been reached,the display will start again at the lowest fan speed.
C) Determining the appropriate fan speed
To achievea significant air quality improvement, the IQAir system should be allowed to filter the
room’sair volume at least twice per hour at the selected fan speed. Please referto the Air Exchange
RateChart on this guide to determine how many air changes per hour can be achieved in differently
sizedrooms at the various fan speed settings.
User Manual
HealthPro® Compact
Swiss Made
IQAir Advanced Air Cleaning System
Set of CastersRemote Control
Including Battery
TechnicalSupport
Should technical problems arise during or after the warranty period,please contact your point of purchase or the
IQAirSolution Center at:
IQAirNorth America, Inc.
10440Ontiveros Place,Unit 1
SantaFe Springs, CA 90670
Phone:[phone]–AIR(247)
Fax:[phone]
e-mail:[email protected]
Toexpedite your service request, please have the following information readywhen contac ting us:
IQAirmodel, shell number and serial number (found on the base of the unit and on the certificate of performance)
Yourdetails (name, address, phone, e-mail)
Pointof purchase (name of dealer, city)
Dateof purchase
Descriptionof problem
Howto Register your IQAir System
Pleasecomplete and return the below card soon after purchase. The information will allow us to provideyou with a
swiftservice should service work become necessary. At your request we will also keep you up-to-date with technical
andpromotional information relating to your IQAir system. (The shell and serial numbers are located on the base of
theunit)
ShellNo:    Serial No.: .
Yourname Company
Address
City/Town State/Province Zip/PostalCode
Dealername Address
City/Town State/Province Zip/PostalCode
Purchasedate
Reasonfor using IQAir
Roomin which IQAir is mainly used
Ifyou would like to be notified about new IQAir products and promotions please enter your e-mail address or
phonenumber here:
Pleasedetach this card and send it to the address printed on the reverse side. Alternatively you can fax this
pageto 1–562–903–7601 or register on the IQAir website www.iqair.com.

Technical Support andWarranty Registration
WarrantyRegistration Card
(Allinformation is treated confidentially and will not be supplied to 3rd parties.)
Technical Support /
Warranty
Tell a Friend about IQAir®…
… and receive a free pre-filter
for e ver y ne w IQAir ®customer referral !
Referral Program
Information
HealthPro Series DVD

Chapter 2 – Setting Up
6
2.2 Choosing a Suitable Location
When choosing a suitable location for the IQAir
system, keep the following considerations
in mind:
•Choosing the most suitable room for the
system will depend on where you would like
the focus of the air cleaning efforts. Two
main considerations are the time you spend
in a particular room and the location of the
main air pollution sources. As a general rule,
the closer the system is located to the air
pollution source, the better the air cleaning
performance in the room.
Although an air cleaning result may be achieved in adjacent rooms, the main air cleaning will take place in the
room where the system is located. For the best air cleaning results in adjacent rooms, make sure that doors to these
rooms are left wide open.
•For best performance, the system should be positioned at least 12 inches (1 foot) away from the nearest vertical
surface, such as a wall or a cupboard. In general, the more centrally the system is positioned, the better the
performance.
•Position the system close to a power outlet and make sure that the power cord is positioned in a way that it does
not present an obstacle in walkways.
•Make sure that the system is positioned in such a way that the control panel is easily accessible.
2.3 Connecting to Power
1. Plug the connector end of the power cord into the recessed power inlet socket on the back of the system.
2. Plug the other end of the power cord into a power outlet or power strip.
Important: The only way to disconnect power completely is to unplug the power cord. If the system is
disconnected from the power supply for more than one hour, the current day and timer will need to be reset.
Do not use the IQAir system when the power cord becomes damaged. The power cord may be replaced with an
approved cord with a two-pole plug. Replacement cords are available from IQAir.
IQAir
min. distance
12” (1 foot)
Control panel should
be easily accessible
Keep power cord
clear of walkways
Power cord plug
Power cord connector
Power inlet socket
Power outlet
(with or without grounding)

7
2.4 Fitting and Removing Casters
Chapter 2 – Setting Up
Attaching the supplied casters is optional. They make it easy to
move the air purifier between rooms.
The caster kit consists of:
1. mounting rail (x 2)
2. casters (x 4)
For installation simply follow the below instructions:
2
2
1
12
34
56
Turn the device upside down on a soft and clean
surface.
Place the mounting rail on the purifier’s base so that
the holes line up with the black connector pins on the
base. The cut-ins should face the center of the unit.
Press down until the mounting rail snaps into place.
Repeat with second rail.
Place the caster onto caster pin.
Press on caster, until it snaps into place. Repeat steps
4 and 5 with the remaining casters.
Ensure that each caster is securely fitted before
placing the air purifier in its upright position onto
the casters.
crescent-shaped
cut-ins

8
Removing Casters From Your IQAir®Air Purifier
Chapter 2 – Setting Up
12
34
56
Switch the device off.
Remove each caster from the rail by pulling it straight
off. The caster pins will be exposed.
There are two slotted tabs on each rail.
Using a flat-head screwdriver, press firmly into the
slotted tab.
Use the screwdriver to gently loosen and lift the rail
away from the base. Lift the rail out by hand. Repeat
steps 5 and 6 for the second rail.
Turn the device upside down on a soft and clean area
or surface.

Chapter 3 – The IQAir® System’s Components
9
Chapter 3 – The IQAir® System’s Components
3.1 Description of Housing Components
The IQAir system features a modular tower design in which all important filtration and air moving components are
positioned vertically in-line, i.e. stacked on top of another. Air is drawn into the system at the base, and passes
through several filter stages to be returned to the room via the diffuser on top of the system.The housing modules
are held together by two locking arms.
•The base with its arched design features air intake openings on two sides.
•The pre-filter module consists of frame 1 and the Pre-Filter which is fixed inside the frame by four filter
clamps.
•The fan assembly comprises two housing modules with the centrifugal fan inside.
•The HyperHEPA filter module consists of frame 2 and the HyperHEPA filter.
•The EvenFlow diffuser contains omni-directional air outlet openings.
•The handle on top of the diffuser is designed for carrying the IQAir system.
•The locking arms hold the housing elements together. When opened, the locking arms allow easy access
to all filters.
EvenFlow Diffuser
Pre-Filter
Frame (Frame 1)
Fan Assembly
HyperHEPA
Filter Frame (Frame 2)
Locking Arms
Base
Handle
Air Intake Opening
Air Outlet Openings
Control Panel

Chapter 3 – The IQAir® System’s Components
10
1. Room air is drawn into the system via two
arched openings at the base.
2. The air is drawn in through a pleated Pre-
Filter that removes most coarse and fine dust
particles.
3. At the heart of the system, sandwiched
between the filters, is a powerful centrifugal fan
which generates the airflow.
4. The air is pushed through an advanced
tightly pleated high-efficiency particulate air
(HyperHEPA) filter media. The HyperHEPA filter
captures the finest of particles.
5. Low turbulence,low velocity air is returned to
the room via the EvenFlow diffuser.
3.2 Description of Removable Components
The IQAir system features a modular housing design which enables the easy replacement of all filter elements in a
matter of seconds. The illustration below shows all the removable components. For more details on how to replace
filters, please refer to Chapter 6 – Replacing Filters.
3.3 How the IQAir® System Works
HyperHEPA
Filter
PreMax Pre-Filter
Frame 2
Frame 1
Filter Clamps
EvenFlow Diffuser
1
2
3
4
5

Chapter 4 – Using the Control Panel
11
4.1.1 Description of Control Panel Keys
Power Key
The Power key switches the IQAir system on and off. When the system is switched off, the fan stops to run, but the
system will remain connected to the power supply (standby mode). The standby mode allows for automatic timer
start-up. In the standby mode, the different menu functions can be accessed.
Tip: In a menu window the Power key also serves as a quick exit key to return to the main display window.
Arrow () Key
When the system is switched on, the key allows the adjustment of the fan speed. In the enter mode, indicated by
the appearance of a black flashing cursor (see“Enter Key” below), the key is used to modify the selected setting in
the display window. Confirmed with the Enter key, the enter mode is automatically terminated. The LCD will then
display the current menu settings for another 15 seconds before reverting to the main window display.
Chapter 4 – Using the Control Panel
The IQAir system is operated and controlled via the electronic control panel which is located at the top of the front
locking arm.
Several operations can be completed via the electronic control panel:
•Switching the system on and off
•Controlling the fan speed and corresponding air delivery rate
•Checking the remaining filter life of the individual filters
•Setting the automatic timer
•Resetting the Filter Life Monitor after replacing a filter
•Locking the control panel to avoid tampering with the system’s settings
•Choosing the desired display language
•Setting the day & time
4.1 Description of Control Panel
LCD = Liquid
Crystal Display
Power
Key
Enter
Key
Menu
Key
Arrow
Key
HyperHEPA Filter Life LED
Pre-Filter Life LED
Timer LED
Fan Speed LEDs
LCD Display
The 2-line LCD displays important information about the system’s settings.
In standby mode, (not running) without the timer activated, the first line
displays the IQAir model name and the word “Standby” is displayed on the
second line. If the timer is activated, the current day and time, and the next
programmed start and stop time will be displayed instead.
If the IQAir system is running and the timer is not activated, the first line displays
the current speed setting and the second line displays the air delivery rate;
however, when the timer is activated, the current programmed start and stop
times will be displayed on the second line.
LED = Light Emitting Diode
Main window: Standby mode
Main window: On mode
Menu window: Filter Life Monitor
Note: Airflow and remaining filter life
may be different on actual air cleaner.
▲
HyperHEPA
Pre-Max

Menu Key
The Menu key allows access to any one of ten menus. Pressing the Menu key once allows access to the first menu
function. Pressing the Menu key twice allows access to the second menu function, and so on. If no key is pressed for
15 seconds in a menu window, the display will revert to the main display window. Tip: If you are in a menu window
and would like to remain in the window for more than 15 seconds, keep the key depressed.
Enter Key
The Enter key, if pressed for 3 seconds, allows the modification of a setting.The enter mode is indicated by a flashing
cursor on the modifiable setting. Pressing the Enter key again will save any entry and move the cursor to the next
modifiable item in the display window.When the last modifiable choice in a window is confirmed with the Enter key,
the enter mode is automatically terminated and the new settings are saved.
Filter Life LEDs: Whenever the system is on, the color of the filter life LEDs (light emitting diodes) indicates the state
of the individual filters in the system. Note: The positions of the filter life LEDs on the control panel correspond to
the actual positions of the filters within the system.
The filter life indicator LEDs signal four possible stages in the life of the filter:
1. Green: The filter is still within 80% of its estimated life span.
2. Orange: The filter is approaching the last 20% of its estimated life span.
3. Red: The filter has reached the end of its estimated life span.
4. Red (blinking): The filter has passed its estimated life span and should be replaced immediately. The IQAir
system’s effectiveness is likely to have been reduced dramatically, either due to a reduction in air-
flow (particle filters are clogged) or a reduction in filter efficiency (gas phase filter is saturated).
Fan Speed LEDs: These LEDs simulate the fan speed through the frequency of their rotation. The faster the rotation
of the fan speed LEDs, the faster the actual fan speed of the unit.
4.2 Control Panel Locking Function
The control panel keys can be locked to avoid tampering with the settings.To lock
or unlock the control panel keys, the Menu and the Enter key have to be pressed
down simultaneously for 3 seconds. The activated locking function is indicated
with a star symbol in the control panel display.The remote control will still operate
the IQAir system when the locking function is activated, only the control panel
keys are locked.
4.3 Fan Speed and Air Delivery
The IQAir system can be set to run at six different fan speeds which correspond to six different airflow rates. Speed 1
is the lowest,speed 6 the highest fan speed.The higher the fan speed,the more room air will be filtered by the system.
The high fan speed settings provide additional air cleaning power to deal with situations of elevated pollution levels.
To allow better evaluation of the system’s performance at different fan speeds, the standard display window shows
not only the fan speed, but also the air delivery rate (airflow). The displayed airflow is factory preset and is not
measured by the system itself. (When Timer is activated, the display will change. Refer to section 4.4.6.)
4.3.1 Regulating Fan Speed
1. When the IQAir system is switched off (standby mode), the first line of the
LCD display shows the model name. To switch the system on, press the
Power key on the far left of the control panel.
2. The LCD now displays the fan speed and the corresponding airflow rate.
Note:The system starts at the fan speed at which it was running when it was
last used.
3. To change the fan speed, press the key. The fan operates in 1 of 6 speeds.
12
Chapter 4 – Using the Control Panel
Enter
Menu
HyperHEPA
Pre-Max

4.3.2 Air Exchange Rates in Differently Sized Rooms
Any air cleaner can only be effective if it filters a sufficient amount of air in an indoor environment. For general air
cleaning purposes, the IQAir system should be able to filter the room air volume at least twice every hour on the set
fan speed to achieve a significant air quality improvement. If the intensity of the pollution source is high or a high
degree of purification is needed, more air changes may become necessary. In order to achieve the desired number
of air changes, more than one room air cleaner may be required, or a HVAC filtration system should be considered.
The number of air changes that are necessary to attain a certain level of indoor air quality will depend on a variety
of factors, including:
•Intensity of air pollution source: The higher the rate at which air pollutants are produced or enter the indoor
environment, the higher the air cleaning rate in the room needs to be.
•Filtration efficiency for specific air pollutants: The lower the filtration efficiency for certain pollutants, the more
air changes are required to reduce these pollutants.
•Desired improvement in air quality: The higher the desired improvement in air quality, the more air changes are
required.
The number of air changes per hour (ACH) produced by an IQAir system in a specic environment are calculated as
follows:
hourly air delivery of the IQAir system (cfm = cubic feet per minute) x 60
= air changes per hour (ACH)
air volume of the room (cu.ft.) (L x W x H)
Note: The air delivery rates of the IQAir system at the various fan speeds settings are listed on the Technical
Specications sheet found at the back of this manual or visit www.iqair.com/support.
Example calculation: A room with the dimensions of 13 x 14 x 8.5 ft. has an air volume of 1,547 cu.ft. With an air
delivery rate of 140 cfm, the room air volume will be circulated over 5.4 times per hour by the
IQAir system (140 cfm = 140 x 60 min = 8,400 cu.ft/h; 8,400 cu.ft/h ÷ 1,547 cu.ft = 5.43 ACH).
4.4 Using the Menu Functions
The IQAir control panel offers a choice of several menu options which allow access to the advanced features of the
system. In total there are ten active menu functions. The functions can be accessed in standby or running mode.
4.4.1 Menu Overview
Pressing the Menu key accesses the menu functions in the following order:
1. Filter Life Monitor
Allows the viewing of the remaining filter life of the individual filters
within the system.
2. Setting the Auto Timer (On/Off Period)
Allows to activate the timer and set the Timer ON period.
3. Automatic Timer (Day of-the-Week Timer)
Allows to activate or deactivate the Timer ON period on particular days
of the week.
4. Timer ON Speed Selection
Allows to set the fan speed for the Timer ON period.
5. Timer OFF Speed Selection
Allows to set the fan speed outside the Timer ON period.
6. Time & Day Setting
Allows to set the current time and day setting.
13
Chapter 4 – Using the Control Panel

Chapter 4 – Using the Control Panel
4.4.2 Filter Life Monitor
The IQAir system is equipped with an electronic Filter Life Monitor that calculates the remaining life of the system’s
filter elements. Thanks to the Filter Life Monitor, the user does not have to guess when filters need to be replaced or
replace them at fixed intervals (which rarely correspond to the actual amount of use). The Filter Life Monitor keeps
track of the most important factors affecting the life of the individual filter elements. The Filter Life Monitor display
shows the remaining life of each individual filter at any given time at the selected fan speed.
1. To reach the Filter Life Monitor display from the main display window, press
the Menu key once.The remaining life of the Pre-Filter will appear first.
2. Press the key to view the remaining life of the other filters in the system.
3. The remaining life of the filter elements is expressed in hours of operation
at the current speed setting. Filter Life will adjust whenever the fan speed is
changed. If the filter is beyond its useful life, a negative number will be
displayed.
How the Filter Life Monitor Works
The basis for the calculating of the remaining filter life is the already elapsed operation time at the set fan speed. This
input is compared with an internal memory bank which contains information about the different filters’ lives under
specific conditions of use.
The Filter Life Monitor makes a calculation of the remaining filter life, taking into account not only past use of the
system, but also likely future use. As reference for future use, the Filter Life Monitor uses the fan speed which is set at
the time.
The relationship between the current fan speed and the remaining filter life displayed can be expressed as follows:
•The higher the current fan speed setting, the shorter the displayed remaining filter life.
7. Filter Life Reset (New Filter)
Allows the resetting of the filter life counter after replacing a filter.
8. Airflow Units
Allows to switch the airflow units between cfm (cubic feet per minute)
and m3/h (cubic meters per hour).
9. Language
Allows to switch the display language.
10. Service Access
This menu is designed for factory access only.
14

Chapter 4 – Using the Control Panel
15
timer status eld
start time stop time
4.4.3 Setting the Auto Timer
The Auto Timer Menu allows the setting of a Timer ON period, which is dened by
a START time and a STOP time. For the Timer ON period, a fan speed can be
selected in the Timer ON Fan Speed Menu (see 4.4.5). The time outside the Timer
ON period is dened as the Timer OFF period for which the air cleaner can be
switched off or for which a different fan speed can be selected in the Timer OFF
Fan Speed Menu (see 4.4.5).
The timer status eld indicates whether the timer function is enabled or disabled
(on or off). Use the time status field to quickly enable/disable the timer.
1. To reach the Auto Timer Menu from the main display window, press the Menu
key twice.
2. Press and hold the Enter key until the cursor starts to ash.
3. Press the key one time to activate the timer.
Note: If the START and STOP times are identical, the timer cannot be activated.
Note: The time is displayed in a 24 hrs. clock, military time.
4. Press the Enter key to save the timer status setting and to proceed to the
START time.
5. Select the desired START hour by pressing the key.
6. Press the Enter key to save the START hour and to proceed to the minute
setting.
7. Select the desired START minute setting by pressing the key.
Note: The minute settings can only be set in ve minute increments.
8. Press the Enter key to save the minute setting, save the START time and to
proceed to the STOP time setting.
9. Select the desired STOP hour by pressing the key.
10. Press the Enter key to save the STOP hour and to proceed to the minute
setting.
11. Select the desired STOP minute setting by pressing the key.
12. Press the Enter key to save the STOP minute setting, save the STOP time and
to exit the enter mode.
Note: The times are displayed in a 24-hour clock.

Chapter 4 – Using the Control Panel
16
4.4.5 Timer ON/OFF Fan Speed Selection Menu
The Timer ON/OFF Fan Speed Selection Menus allow the setting of two
different fan speeds for two different time periods (referred to as Timer ON
period and Timer OFF period). For the Timer ON period you can select fan
speeds 1 to 6. For the Timer OFF period you can select fan speeds 0 (OFF) to 6.
1. To reach the Timer ON Fan Speed Selection Menu from the main display
window, press the Menu key four times.
2. Press and hold the Enter key until the black cursor appears.
3. Press the key to select the desired speed for the Timer ON period.
4. Press the Enter key to confirm the chosen speed and to exit the enter
mode.
5. To set the Timer OFF period fan speed, press the Menu key one more time.
Press and hold the Enter key until the black cursor appears and adjust the
Timer OFF fan speed as above.The final Enter command saves the selection
and exits the enter mode.
4.4.4 Day-of-the-Week Timer
The Day-of-the-Week Timer allows the deactivation of the Timer ON period on
certain days of the week. In its default setting the Timer ON period is enabled
on all seven days of the week.This is indicated by stars below the abbreviations
of the days. On days without a star the air cleaner will be running at the speed
which is set in the Timer OFF Speed Selection Menu (see 4.4.5).
Note: At least one day of the week must be activated with a star to enable the
Auto Timer. If the timer is disabled on all days of the week, the timer status eld
in the Auto Timer Menu will switch to OFF and the timer will be disabled.
1. To reach the Weekly Timer Menu from the main display window, press the
Menu key three times.
2. Press and hold the Enter key until the cursor appears.
3. Press the key to activate (star) or deactivate (no star) the Timer ON
period on a particular day. Press the Enter key to proceed to the next day.
4. Repeat the same procedure until the timer has been activated/deactivated
on the desired days.The final Enter command exits the enter mode.

Chapter 4 – Using the Control Panel
17
4.4.6 Timer Information in the Control Panel
The IQAir control panel shows the timer status without the need to access the Timer related menus.
Display’s Main Window Timer LED
• System is on standby
• Timer is deactivated
System on Standby: The first line shows the
model name and the second line shows the word
“Standby”. The Timer LED is red.
System Running: The first line shows the fan
speed and the second line shows the airflow. The
Timer LED is off.
System on Standby: The first line shows the
current day & time and and the second line shows
the next time the system will turn on.The Timer LED
is green.
System Running: The rst line shows the fan
speed and the second line shows the current Timer
ON period (start and stop times). The Timer LED is
green.
• System is running
• Timer is deactivated
• System is on standby
• Timer activated to start on Thursday
• System is running
• Timer is activated
red
off
green
green
Display’s Main Window Timer LED
Timer Deactivated
Timer Activated

18
Chapter 4 – Using the Control Panel
4.4.8 Filter Life Reset (New Filter)
The Filter Life Reset function allows the Filter Life Monitor to be reset after a new
filter has been inserted. As a result, the appropriate filter life LED on the control
panel will be reset to green and the hour count in the Filter Life Monitor menu
will be reset to the full life span of the new filter. Note: Resetting the Filter Life
Monitor will also cancel the “Replace Filter” warning from the main display
window.
1. To reach the Filter Life Reset function from the main display window, press
the Menu key seven times.
2. Press and hold the Enter key until the flashing cursor appears. Release the
Enter key. The first filter selection to appear is the pre-filter.
3. Press the key to select the filter that has been replaced.
The filter life LED for the appropriate filter is now flashing red.
4. Press the Enter key to confirm that the selected filter has been replaced.
5. Press the Enter key one more time to confirm the filter change.
Or to exit, press the Menu key (M-Menu).
6. Upon successful reset of the filter life, the new remaining filter life (taking the
currently selected fan speed into account) will be displayed,and the filter LED
light on the control panel will change from red to green.
4.4.7 Time & Day Setting
When the IQAir system is first connected to the power, the day and time displayed
will be incorrect and will have to be set for the timer function to work properly.
Once the current day and time are set, they will only need to be reset if the system
is disconnected from the power supply for more than an hour.
1. To access the Time & Day menu from the main display window, press the Menu
key six times.
2. Press and hold the Enter key until the cursor starts to flash.
3. Select the hour by pressing the key.
4. Press the Enter key to save the hour setting and to proceed to the minute setting.
5. Select the minutes by pressing the key.
6. Press the Enter key to save the minute setting and to proceed to the day
setting.
7. Select the day of the week by pressing the key.
8. Press the Enter key to save the day setting and to exit the enter mode.
9. Press the Power key to return to the main display. Note: The display will
automatically return to the main window if no key is pressed for 15 seconds.

4.4.10 Language Setting
The Language Menu allows to change the IQAir system’s display language.The
languages from which you can choose will depend on the model and the
country of purchase.
1. To reach the Language Menu from the main display window, press the
Menu key eight times.The current language is displayed.
2. To change the display language, press and hold the Enter key until the
cursor starts to flash.
3. Use the key to scroll through the display language options.
4. Press the Enter key to save the desired display language and to exit the
enter mode.
19
Chapter 4 – Using the Control Panel
4.4.9 Changing the Airow Units
1. You can reach the airflow units menu by pressing the Menu key eight times.
2. You can change the airow units which are displayed from cubic feet per
minute (cfm) to cubic meters per hour (m3/h), and vice versa, by pressing the
Enter key for three seconds either when the system is switched on or in
standby mode.
3. When the rst character of the airow units starts to ash, press the key
once to change the units.
4. Press the Enter key to confirm the air flow unit change. Until modified again,
the airflow rate will now be displayed in the newly selected units.
Note: The air delivery (airflow units) displayed in this manual are examples only
and will vary according to model.

Chapter 5 – Using the Remote Control
Position of IR receiver
20
Chapter 5 – Using the Remote Control
In addition to the control panel, the IQAir system can be controlled by using the hand-held remote control.
The remote control can be used to: •Switch the system on and off
•Select the desired fan speed
•Activate and deactivate the timer function (Note: Start and stop times
can only be set and changed directly on the system’s control panel)
5.1 Description of Remote Control Elements and Functions
Switching the System On and Off: To switch the IQAir system on with the remote control,press any one of the speed
control keys marked with 1 through 6. The system will still start at the fan speed of the pressed key.To switch the IQAir
system off, press the OFF key.
Switching the Timer On and Off: If start and stop times have been set in the Weekly Auto Timer Menu, it is possible
to switch the timer on and off with the remote control.To switch the timer on, press the Timer Modification key and
then the Timer ON key. To switch the timer off, press the Timer Modification key and then the Timer OFF key.
5.2 Getting the Best Transmission Results
The IR (infrared) receiver of the IQAir system is positioned underneath the control panel cover.In order to get the best
signal transmission, the remote control should be pointed at the control panel when a remote command is being
carried out. Alternatively,the remote control should be pointed at a surface like a wall, ceiling or window, from which
the signal can bounce off in a right angle (90°) to the electronic control panel.
Indirect transmission
(bouncing off surface)
max. distance: 15 ft.
Direct transmission
max. distance: 20 ft.
Infrared (IR) diode
Standby (off) key
Timer ON key
Speed control keys Timer modification key
Timer OFF key
Battery compartment
(Battery type: CR2025)