iRest ICOMFORT PLUS User manual

SAVE THESE INSTRUCTIONS
OPERATION INSTRUCTIONS
ICOMFORT PLUS MASSAGE CHAIR
Irelax Limited www.irelax.co.nz [email protected]

01
Thank you for purchasing this product. Before you use it, please read the Operation
Instructions in detail for the correct usage of this product, especially the important
safety warnings. Keep the Operation Instructions properly for future reference.
Note: Our conpany reserves the right to change and explain any product design
without prior notice. Product colors are subject to the actual products.
02-03
04-05
06
07
09-10
10-36
10
10-27
28
29
30
30
30
31
32
32
33
Safety and Maintenance
Safety Warning
Name of Components
Function
Introduction to the Remote Controller
Method of Usage
I.Turn on the power supply of this product
II.Massage Function Control Operation
III.Introduction to Armrest Shortcut Keys
IV.Voice Control Instruction
V.Turn off the power and stop massage
VI.Operation Instructions for Bluetooth Speaker Play
VII.Installation Instructions for Legrest
VIII.Instructions for Removal and Use of Head Cushion and Backrest
IX.Floor Protection
X. Instruction for Movement
Product Specification
TABLE OF CONTENTS

0302
Safety and Maintenance Safety and Maintenance
1.Important Safety Warnings
·Do not allow children to touch any movable part of this product.
·Use the well-grounded power supply unit suitable for this product.
·Pull out the plug after use or before cleaning to avoid any physical injury or damage to
the product.
·Operate this product as instructed in this manual.
·Do not use any parts or accessories which are not recommended.
·Do not use this product outdoors.
·Please read the Operation Instructions carefully before operation.
·Never use this product for any other purpose not listed herein.
·20 minutes of usage each time is recommended.
·Do not use this product if the leather is broken or damaged.
·Do not use this product if the cover or leather is broken or damaged.
·Do not use this product if the radiator hole is covered or blocked.
·Do not drop anything into this product.
·Never fall asleep while using this product.
·Do not use this product if you are drunk or feel unwell.
·Do not use this product within one hour after a meal.
·Do not use this product with excessive force to avoid any injury.
·Do not carry any fragile, explosive, or combustible material in your pocket, such as a
mobile phone and lighter when using the massage chair.
2. Operating Environment
·Do not use this product in a very moist environment such as the bathroom.
·Stop using this product immediately when the ambient temperature changes sharply.
·Do not use this product in any heavily-dusty or caustic environment.
·Do not use this product in a small space or a place without good ventilation.
·The normal room temperature ranges from 0 °C to 35 °C.
·Do not use this product in an excessively humid room such as a bathroom. Use it at a
relative humidity between 20% and 80%.
·Do not use this product outdoors.
·Avoid direct sunlight.
·Keep this product away from any heat source such as a stove and air outlet of an air
conditioner.
·Do not use this product during thunder or lightning weather.
·Do not use this product in dusty places.
3. The following populations should not use this product
·Patients with osteoporosis.
·Patients with heart disease or wearing electronic medical devices such as a
pacemaker.
·People who have a fever.
·Pregnant women or women on their menstrual period.
·Patients who are injured or have a skin disease.
·When unsupervised, any children are under the age of 14 and those unconscious are
not allowed to use this product.
·People who are told by their physicians to have rest or who feel unwell.
·People whose bodies are wet are forbidden to use this product.
·This product has a hot surface. Persons insensitive to heat must pay attention when
using this product.
4. Safety Precautions
·Check whether voltage is consistent with the specification of this product.
·Never insert or pull out the plug with a wet hand.
·Do not let water flow into this product to avoid electric shock or cause damage to this
product.
·Do not pull the power cord when plugging or unplugging it. Rough handling is
forbidden.
·Do not damage the wire or modify the circuit of this product.
·Do not clean live parts of this product with a wet cloth such as a power switch and plug.
·Be away from this product in case of power failure to avoid any injury if power is
restored suddenly.
·Stop using this product at once while it works abnormal, and consult your local supplier.
·Stop using this product if you feel unwell, and consult your health care practitioner.
·This product is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning the use of this product by
the personnel responsible for their safety. Children should be supervised to ensure that
they do not play with this product.
·If the power cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified staff in order to avoid hazards.
5. Product Service and Maintenance
·This product should be maintained by the service center designated by the
manufacturer only. No user should disassemble or maintain it without permission.
·Do not forget to turn off the main power switch after usage.
·Do not use this product if the power socket becomes loose.
·If this product will be left unused for a long period of time, it is necessary to roll up the
power cord of this product and store this product in a dry and dust-free environment.
·Do not store this product at a high temperature or near open flame. Avoid prolonged
exposure to direct sunshine.
·Please clean this product with dry cloth. Never use thinner, benzene or alcohol.
·The mechanical components of this product are specially designed and manufactured,
so no special maintenance is needed.
·Do not use a sharp object to stab at this product.
·Do not roll or pull this product on any uneven ground. Instead, it should be lifted before
moving.
·Please use this product intermittently. Do not keep it working continuously for a long
period of time.
6. Solutions to Ordinary Malfunctions
·If the motor sounds during operation of this product, this is the normal operation sound.
·If the controller cannot work normally, check whether the plug and the power socket are
connected reliably, and whether the power switch is turned on.
·If the rated working time is over, this product will automatically activate the power-off
button; If this product keeps operating for a long period of time, the temperature
protector will stop this product automatically. The product can be used again after half
an hour.
7. Storage Conditions
·Storage room temperature: -5 °C to 35 °C.
·Relative humidity (RH) between 20% and 80%; free of corrosive gases, and a well-
ventilated room.

0504
Safety Warning Safety Warning
Warning Warning
When the legrest of the massage chair is lifted, nobody should apply pressure on
the legrest to prevent the massage chair from falling forward which will damage this
product or result in personal injuries.
Do not remove or pull out the remote controller cable or the power cord in the
standby or power-on state to avoid any damage to this product or accidental electric
shock of a body part. You are advised to unplug the remote controller cable and the
power cord and put them away after you use the massage chair.
Warning
Before sitting on the massage chair, make sure that the massage chair manipulator
does not stay in the seat cushion position to avoid discomfort to the buttocks during
the body pressing down and any damage to the massage chair manipulator.
Warning
When the zero-gravity lying function is enabled, be sure to check whether there is
any child or pet staying or playing under the bottom of the legrest and backrest, in
order to avoid any damage to this product or physical injury.
禁⽌下压

06 07
Name of Components
1. Head pillow
2. 3D digital speaker
(left side with voice
control device)
3. Shoulder airbag parts
4. Arm airbag parts
5. Pocket for remote control
or mobile phone
6. USB charger
7. Seat
8. Calf part
9. Foot part
10. Back part
11. Armrest
12. Handrail shortcut key
13. Side cover
14. Back plastic cover
15. Remote controller
16. Driver box cover
17. Moving roller
18. Power cable & plug
19. Fuse
20. Power switch
21. Power plug connector
Function
· This product has designed a set of massage manipulator that can walk up and
down, four-wheel drive and mute design.·
· There are five simulated massage techniques: finger pressing, kneading,
tapping, tapping and kneading at same time.
· Equipped with shoulder automatic positioning detection.
· Automatic massage functions: automatic massage includes 8 kinds of automatic
massage functions, including comfortable massage, relaxing massage, stretch
massage, shoulder and neck massage, back and waist massage, whole body
massage, fast massage ,spinal massage.
· With two memory function : iMenory 1, iMenory 2.
· Equipped with upper body manual massage function (the whole body, fixed point
and local, upper back ,lower back ,totally five massage parts are selected, and
the speed of each massage manipulation can be adjusted with five speed. In
fixed point and local state, the manipulator can adjust the position up and down;
When tapping, pressing and percussion massage, the width of the massage ball
can be wide, medium or narrow.
· Air pressure function : shoulder airbag massage (totally 4 airbags) ,armrest
airbag massage (totally 8 airbags), foot airbag massage (totally 12 airbags), there
level intensity adjustable.
· Zero wall design for save the room space.
· Backrest frame guide adopts curve guide technology, which completely conforms
to the curve of human back, and can enjoy massage from head to thigh.
· Music playback system, 3D digital audio built into left and right shoulder. Use
the Bluetooth function of the smart device to play music wireless.
· Equipped with intelligent voice control recognition function.,left armrest with voice
control wake up button , voice control can be optional stop or start.
· In the left and right palm air bags, there is a salient massage with a magnetic
massage function.
· Calf rest lifting or recline adjustment, lifting or recline adjustment of leg and back,
zero gravity I or zero gravity II and time setting adjustment function.
· At the bottom of foot have roller massage function, three pairs of rollors massage
on toe root; scraping massage function on the arch and heel.
· At the calf have kneading massage function which can relieve the stiffness and
stress of calf.
· Back heat , adopt with Carbon fiber far infrared heating.
· Left armrest with button : on/off button, footrest lifting&lying button, Auto mode
button, voice control wake up button.
· The right handrail is equipped with USB charging function.
· TFT Color screen controller.
· Shutdown automatic sitting function, manipulator automatic reset function.·
14
16
18
15
17
19 20 21
FUSE:
T5AL 250V POWER INPUT
ON/ OFF
1
2
3
4
8
10
11
712
13
6
5
9

ZERO
2
"Up & Down" to select,"OK"to confirm.
Auto-Fast
Speed Width
Arms air
Foot Roll
Adjustment
Shoulder
Temperature
0908
114
2
3
4
5
6
15
16
7
8
17
9
10
11
12
18
21
1
2
4
5
6
7
8
9
10
11
12
13
14
15
16
18
19
20
21
17
13
19
20
3
Introduction to the Remote Controller Introduction to the Remote Controller
Remote Controller Interface
Note: The remote controller displays the colors, massage function messages
and massage function icon layout order. Please refer to the physical display!
1. TFT color LCD
2. Massage function status bar
3. Anion generator display
4. Time display
5. Zero gravity display
6. Back stretching display
7. Air pressure display for the arms
8. Air pressure display for the legs and feet
9. Foot roller display
10. Speed adjustment
11. Adjustment
12. Shoulder position adjustment
13. Bluetooth display
14. Massage mode display
15. Massage position display
16. Back heat treatment display
17. Width adjustment
18. Temperature adjustment for heat
treatment
19. Air pressure adjustment
20. Roller adjustment
21. Information bar
Remote Controller Buttons
1.On/off: start or close massage chair
2.Adjustment: enter to the interface to adjust
the function
3.Auto: enter to the interface to choose auto
program
4.Menu: enter to the interface of main menu
5.Up: go up
6.Ok: confirm
7.Left: go left
8.Backrest lifting: adjust the backrest lifting
angle
9.Backrest lying: adjust the backrest lying
angle
10.Down: go do
11.Backrest & footrest lifting: chair seat up
12.Backrest& foot rest lying: chair lying down
13.Time setting: adjust the working time
14.Pause button: Pause the massage
15.Manual program: enter to the interface to
choose manual program
16.Back: go back to Massage working
interface
17.Right: go right
18.Footrest lifting: adjust the footrest lifting
angle
19.Footrest lying: adjust the footrest lying
angle
20.Zero gravity I: adjust the Zero gravity I
21. Zero gravity II: adjust the Zero gravity II

1110
·After detecting the shoulder position, the buzzer will beep. If there is any difference
from the actual shoulder position, adjust it to the appropriate position by pressing
the "UP" or "DOWN" key. The shoulder position has 11 adjustable levels. If there is
no shoulder position adjustment within 10 seconds, the massage function will start
automatically. Alternatively, press "OK" directly to start massage immediately. If no
shoulder position can be detected, massage will be started according to the
shoulder height by default.
·Press the power button to start massage. The backrest and legrest will automatically
lie down based on the preset angles.
·After automatically lying down, the massage chair will automatically detect the
shoulder position and body shape. Wait until the detection is completed.
Alternatively, press "OK" to skip such detection. The default value will be adopted
automatically to start massage. ·In the current interface, you can use the
navigation keys to go up and down to select the
"Adjustment" button or "Shoulder Position". After
selecting the function to be set, press "OK" to
enter.
Method of Usage Method of Usage
POWER INPUT
POWER INPUT
I. Turn on the power supply of this product
II. Massage Function Control Operation
1.Standby
·After the massage chair is powered on or turned off or
when it is in standby mode, it cannot enter any mode of
operation, except the settings.
2.Start massage (power switch)
Just a moment,
Press 'OK' for default setting.
Body Sensing
Just a moment......
Attention! Ensure that there are no
objects around the massage chair.
Angle adjustment
02
Shoulder Adjust
06
·High shoulder position
·Suitable shoulder position
·Low shoulder position
Button Description
Move the massage balls upward to a suitable shoulder position.
Move the massage balls downward to a suitable shoulder position.
OK
ZERO
2
"Up & Down" to select,"OK"to confirm.
Auto-Fast
Speed Width
Arms air
Foot Roll
Adjustment
Shoulder
Temperature
"Up & Down" to adjust,"OK"to exit.
Plugging-in diagram Product connection
diagram
Power switch diagram
of the product

3.Pause button
·While the massage function is running, press the "Pause" button to temporarily
stop all the massage functions; press the "Pause" button again to continue the
massage function before pause. If the pause time exceeds 20 minutes, all the
massage functions will be automatically turned off.
·Press the "Menu" button to enter the main menu massage function selection
interface, including: automatic function, manual mode, adjustment, customize,
settings, and equipment information function interface.
·Press the "UP/DOWN" button to choose the massage function. Press "OK" to
confirm that you have entered the massage function menu selected. Press the
"Back" button to return to the selected function operation status information
interface.
1312
·Press the "Menu" button to enter the main menu interface, and select the automatic
function icon: The automatic mode consists of fast massage, comfortable massage,
relaxing massage, stretching massage, full body massage, chiropractic massage,
neck & shoulder massage, and back & waist massage modes.
·Press the "UP/DOWN" button to choose the massage function. Press "OK" to
confirm that you have entered the massage function menu selected. Press the
"Back" button to return to the selected function operation status information
interface.
Method of Usage Method of Usage
Massage function
running status
Massage function
pause status
4.Menu
5.Automatic function (AUTO key: You can also press the "AUTO" key directly
to enter the automatic function interface.)
"Up&Down" to select,"OK"to confirm.
Auto Function
Fast Massage
Relax Massage
Comfortable Massage
Stretch Massage
Full Body Massage
ZERO
2
Time Out
"Up & Down" to select,"OK"to confirm.
Speed Width
Arms air
Foot Roll
Adjustment
Shoulder
Temperature
ZERO
2
"Up & Down" to select,"OK"to confirm.
Auto-Fast
Speed Width
Arms air
Foot Roll
Adjustment
Shoulder
Temperature
Main menu
"Up&Down" to select,"OK"to confirm.
Auto Function
Manual Mode
Adjustment
Customise
Setting
Device Information
Main menu
"Up&Down" to select,"OK"to confirm.
Auto Function
Manual Mode
Adjustment
Customise
Setting
Device Information
Function
Fast
massage Experience all the massage effects quickly.
The most comfortable massage experience.
Gentle and comfortable deep massage to relieve your body
fatigue and relax the body.
Stretch your legs and waist through the legrest and the backrest to
effectively remove fatigue, relieve joint pain and restore vitality.
Deep massage to rejuvenate your body.
With the unique massage technique for the neck and shoulder, the
effective massage for the cervical spine and scapula can be
performed to relieve the neck and shoulder pain and reduce fatigue
on the neck and shoulder.
Focus on the back and waist massage to relieve the pain on the
back and waist.
Comfort
massage
Relax
massage
Stretch
massage
Full body
massage
Neck&
shoulder
massage
Back&waist
massage
Note: The automatic function already selected will be displayed in the massage
function status bar. You can directly press the "Back" button to view the running
status.
Description
Focus on chiropractic massage, and relax your body and mind.
Spinal
massage

1514
·Press the "Menu" button to enter the main menu interface, and select the manual
mode icon: including massage technique, massage part, airbag massage, and other
massage functions.
·Press the "Left" or "Right" button to switch among the submenus. Then press the
"UP" or "DOWN" button to select the massage function. Press the "Back" button to
return to the running status information interface.
·Manual mode (massage techniques): including five different massage techniques,
such as kneading, tapping, simultaneous kneading and tapping, shiatsu, and
knocking. In the massage state of tapping, shiatsu and knocking, the massage ball
width is adjustable.
·Press the "UP/DOWN" button to select the massage technique icon. Then press
"OK" to confirm that the massage technique will be applied.
·Manual mode (massage area): including such massage functions as fixed point,
local, full back, upper back, and lower back.
·Press the "UP/DOWN" button to select the area function icon. Then press "OK" to
confirm the area selected.
Method of Usage Method of Usage
6. Manual mode (Manual button: You can also press the "Manual" button
directly to enter the manual mode interface.)
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Massage Area
Manual mode
Upper back
Full back
Part
Fixed
Wise
Stop
Knead
Tap
Knead&Tap
Manual mode
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Others
Back heater off on
off on
off on
off on
off on
off on
Foot Roll
Negative ions
Bluetooth
Manual mode
Legs Knead
01)Manual mode (manual button-massage mode)
Note: Selecting the
stop icon will stop all
the massage
technique functions
of the method;
selecting a massage
technique icon will
enable the individual
massage technique.
Wise
Knead
Tap
Knead&Tap
Manual mode
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Knead
02). Manual mode (manual button - massage area)
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Massage Area
Manual mode
Upper back
Full back
Part
Fixed
Fixed point state Local state
Main menu
"Up&Down" to se lect,"OK"to confirm.
Auto Function
Manual Mode
Adjustment
Customise
Setting
Device Information
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Air
Manual mode
off on
off on
Lower air
Upper air
Manual mode
"Up&Down" to select,"OK" to confirm.
Speed Width
Arms air
Foot Roll
Adjustment
Shoulder
Temperature
Manual mode
"Up&Down" to select,"OK" to confirm.
Speed Width
Arms air
Foot Roll
Adjustment
Shoulder
Temperature
Manual mode
"Up&Down" to select,"OK" to confirm.
Speed Width
Arms air
Foot Roll
Adjustment
Shoulder
Temperature
Kneading
Function
Description
Shiatsu
Simultaneous kneading and tapping
Knocking
Speed
Speed, width
Speed
Speed, width
Speed, width
·5 speed levels
adjustable
·3 width levels
adjustable
Tapping

·Manual mode (airbag massage): including airbag massage functions for the upper
body and the lower body.
·Press the "UP/DOWN" button to choose different airbag massage functions. Press
"OK" to confirm your choice.
·Manual mode (other massage functions): including such massage functions as heat
treatment on the back, leg kneading, foot roller, anion generator, and Bluetooth.
·Press the "UP/DOWN" button to choose the massage function. Press "OK" to
enable or disable such massage function.
1716
·Manual mode (others - back heat )
·Click "OK" to enable or disable the back heat treatment function; this is the far
infrared heating function, and the back will become warmer after such heating for
3min.
·Press the "UP" or "DOWN" button to select other massage functions. Press the
"Back" button to return to the running status information interface.
Method of Usage Method of Usage
03).Manual mode (manual button - airbag massage)
04).Manual mode (manual button - others)
Full back state Upper back state Lower back state
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Others
Back Heater off on
off on
off on
off on
off on
Foot Roll
Voice Control
Manual mode
Legs Knead
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Others
Back Heater off on
off on
off on
off on
off on
off on
Foot Roll
Voice Control
Manual mode
Legs Knead
Manual mode
"Up&Down" to select,"OK" to confirm.
Speed Width
Arms air
Foot Roll
Adjustment
Shoulder
Temperature
Manual mode
"Up&Down" to select,"OK" to confirm.
Speed Width
Arms air
Foot Roll
Adjustment
Shoulder
Temperature
Manual mode
"Up&Down" to select,"OK" to confirm.
Speed Width
Arms air
Foot Roll
Adjustment
Shoulder
Temperature
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Air
Manual mode
off on
off on
Lower air
Upper air
"Up & Down" to select,"OK"to confirm.
Manual mode
Speed Width
Arms air
Foot Roll
Adjustment
Shoulder
Temperature
"Up & Down" to select,"OK"to confirm.
Manual mode
Speed Width
Arms air
Foot Roll
Adjustment
Shoulder
Temperature
Main menu
"Up&Down" to adjust,"OK"to exit.
Auto Function
Manual Mode
Adjustment
Customise
Setting
Device Information
Auto-Fast
"Up&Down" to select,"OK" to confirm.
Speed Width
Arms air
Foot Roll
Adjustment
Shoulder
Temperature
Function Description
Fixed point
Local
Upper back
Lower back
Full back
Massage at fixed point
Local round-trip massage in a
small area
Round trip massage on the upper back
Round trip massage on the lower back
Round trip massage on the full back
When choosing the fixed point and
local massage technique, you can
adjust the massage area by
pressing the "UP/DOWN" button.
Function Description
Airbag massage for the
upper body
Airbag massage for the
lower body
Enable or disable the airbag massage function for the
upper body
Enable or disable the airbag massage function for the
lower body
Bluetooth
Bluetooth

·Manual mode (others - legs knead)
·Press "OK" to enable or disable the leg kneading massage function.
·Press the "UP" or "DOWN" button to select other massage functions. Press the
"Back" button to return to the running status information interface.
1918
·Manual mode (other - Bluetooth)
·Press "OK" to enable or disable the Bluetooth function.
·After a Bluetooth-enabled audio source device (e.g. mobile phone, MID tablet) is
connected with the Bluetooth module of the massage chair, the music played by the
audio source device can be wirelessly transmitted to the audio system of the
massage chair via Bluetooth for music playback.
·Press the "UP" or "DOWN" button to select other massage functions. Press the
"Back" button to return to the running status information interface.
·Manual mode (others - foot roll)
·Press "OK" to enable or disable the foot roller massage function.
·Press the "UP" or "DOWN" button to select other massage functions. Press the
"Back" button to return to the running status information interface.
Method of Usage Method of Usage
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Others
Back Heater off on
off on
off on
off on
off on
Foot Roll
Voice Control
Manual mode
Legs Knead
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Others
Back Heater off on
off on
off on
off on
off on
Foot Roll
Voice Control
Manual mode
Legs Knead
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Others
Back Heater off on
off on
off on
off on
off on
Foot Roll
Manual mode
Legs Knead
Auto-Fast
"Up&Down" to select,"OK" to confirm.
Speed Width
Arms air
Foot Roll
Adjustment
Shoulder
Temperature
Auto-Fast
"Up&Down" to select,"OK" to confirm.
Speed Width
Arms air
Foot Roll
Adjustment
Shoulder
Temperature
Bluetooth
Bluetooth
Bluetooth
Voice Control
·Manual Mode ( others --voice control)
·Press” ok “button to start or close the voice control.
·Press “up” or “down” button to choose other function . Press” back “ to back to
status information interface.
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Others
Back Heater off on
off on
off on
off on
off on
off on
Foot Roll
Manual mode
Legs Knead
Bluetooth
Voice Control

·Press the "Menu" button to enter the main menu interface, and select the
adjustment function icon: including such massage functions as massage
technique, massage area, and massage intensity (only timing available now).
·Press the "Left" or "Right" button to switch among the submenus. Select the
massage function in the menu. Then press the "UP" or "DOWN" button to select
the massage function to be adjusted. Press "OK" to confirm your choice, or press
the "Back" button to return to the running status information interface.
·Adjustment function (massage area): In the fixed point or local massage area state,
such manipulator will move upward if you hold down the "UP" button; after you
release it, such movement will stop. Such manipulator will move downward if you
hold down the "DOWN" button; after you release it, such movement will stop. Press
the "UP" or "DOWN" button to select the massage area for adjustment.
2120
Method of Usage Method of Usage
7. Adjustment function (Adjustment button: You can also press the
"Adjustment" button directly to enter the adjustment function interface.)
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Adjustment
Wise
Speed
Width
Adjustment
Massage Area
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Adjustment
Others
Time Setting
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
01) .Adjustment function (adjustment button - massage techniques)
·Adjustment function (massage techniques): the massage technique adjustment
function is for the adjustment of massage speed and massage functions.
·Press the "UP" or "DOWN" button to select the speed or width function. Then press
"OK" to adjust the speed and width.
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Adjustment
Wise
Speed
Width
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Adjustment
Wise
Speed
Width
Note:
·Speed: The massage speed of manipulators is adjustable; there are 5 speed levels.
·Width: In the massage state of tapping, shiatsu and knocking, there are three width
levels for switching.
02) .Adjustment function (adjustment button - massage area)
Adjustment
Massage Area
"Left&Right" to select sub menu,
"Up&Down" to change massage area
Adjustment
Massage Area
"Left&Right" to select sub menu,
"Up&Down" to change massage area
Main menu
"Up&Down" to adjust,"OK"to exit.
Auto Function
Manual Mode
Adjustment
Customise
Setting
Device Information
Adjustment
Intensity
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Foot roll
Temperature
Air
·Adjustment function (massage intensity): including such massage functions as
airbag massage and roller; there are 5 levels of intensity for switching. For the
temperature adjustment for heat treatment, there are 3 temperature levels.
·Press the "UP" or "DOWN" button to select the air pressure intensity or the roller
massage intensity. Then press "OK" to confirm such intensity.
03). Adjustment function (adjustment button - massage intensity)

2322
·Adjustment function (other adjustments): only timing
available now. When "OK" is pressed every time, the
duration will increase by 5 minutes; if it exceeds 40min,
40min will be reduced.
·Press "OK" for time adjustment (when "OK" is pressed
every time, the duration will increase by 5 minutes; the
minimum duration is 5min, and the maximum duration is
40min). Press the "Back" button to return to the running
status information interface
·Press the "Menu" button to enter the main menu interface. Select the "Settings"
function icon to enter the setting interface for language, backlight, auto-lock and
other settings.
·Press the "Left" or "Right" button to switch among the submenus. Press the "UP" or
"DOWN" button for function selection. Press the "Back" button to return to the
running status information interface.
·Press the "Menu" button to select "Customize" in the main menu. Then enter the
"Intelligent Custom Memory" interface to select a specific interface, including:
Intelligent Custom Memory I & II, and other storage or call function.
·Press the "Left" or "Right" button to select the storage or call function. Then press
"OK" to confirm your choice.
·Press the "UP" or "DOWN" key to select Intelligent Custom Memory Ⅰ or Intelligent
Custom Memory Ⅱ.
·Storage: Store the massage mode, massage technique, airbag massage mode and
intensity under the current running status, the position and angle of the legrest and
the backrest, and other massage functions.
·Call: Call the massage mode, massage technique, airbag massage mode and
intensity, the position and angle of the legrest and the backrest, and other massage
functions previously stored.
·Press the "Back" button to return to the running status information interface.
Method of Usage Method of Usage
04).Adjustment function (adjustment button - other
adjustments)
Adjustment
Others
Time Setting
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
8.Customize
Customise
iMemory I
iMemory II
Use Save
Use Save
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
9.Setting
Main menu
"Up&D own" to adj ust,"OK"to exit.
Auto Function
Manual Mode
Adjustment
Customise
Setting
Device Information
Setting
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Back Light
Light
English
Setting
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Language
China
Adjustment
Intensity
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Foot roll
Temperature
Air
Adjustment
Intensity
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Foot roll
Temperature
Air
Adjustment
Intensity
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Foot roll
Temperature
Air
Main menu
"Up&Down" to adjust,"OK"to exit.
Auto Function
Manual Mode
Adjustment
Customise
Setting
Device Information
Setting
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Lock Screen
Sleep
Sleep after 2 Min of inactivity

2524
·Settings (language): Select Chinese or English.
·Press the "UP" or "DOWN" button to select the language type. Press "OK" to
confirm your choice. Then press the "Back" button to return to the running status
information interface.
·Settings (auto-lock): Press "OK" to adjust the auto-lock duration. There are six
options for the auto-lock duration: 15 sec, 30 sec, 1min, 2min, 3min, or never. Press
"OK" for adjustment; or press the "Back" button to return to the running status
information interface.
·Press the "Menu" button to enter the main menu interface and select the equipment
information function. The information such as the model of the current equipment
will be displayed.
·Press the "UP/DOWN" button for selection. Then press "OK" to confirm your
choice. Press the "Back" button to return to the running status information interface.
·Set the (backlight) brightness. Press "OK" to adjust the brightness. There are 5
brightness levels for your option. Press the "Back" button to return to the running
status information interface.
Method of Usage Method of Usage
01) .Setting (language)
English
Setting
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Language
China
English
Setting
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Language
China
02) .Setting (auto-lock)
Setting
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Lock Screen
Sleep
Sleep after 02 S of inactivity
Setting
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Lock Screen
Sleep
Never sleep
Never
03) .Setting (backlight)
Setting
"Left&Right" to select sub menu,
"Up&Down" to select,"OK" to confirm.
Back Light
Light
10.Device information
Main menu
"Up&Down" to select,"OK"to confirm.
Auto Function
Manual Mode
Adjustment
Customise
Setting
Device Information
1 1 1 1 1 1 1 1 1 1 1
Device Information
Code

2726
·Press the "Zero Gravity" key to enable the zero gravity adjustment function. Upon
your request, you can select the position for "Zero Gravity I" or "Zero Gravity II".
·During adjustment of any massage function, if you want to return to the main
interface, you can press the back button to return to the running status information
interface.
Method of Usage Method of Usage
13.Lying angle adjustment button
11.Zero gravity key
Button Description
Zero Gravity I: Adjust to the angle for Zero Gravity I.
Zero Gravity II: Adjust to the angle for Zero Gravity II.
12.Back button
"Up & Down" to select,"OK"to confirm.
Auto-Fast
Speed Width
Arms air
Foot Roll
Adjustment
Shoulder
Temperature
ZERO
"Up & Down" to select,"OK"to confirm.
Auto-Fast
Speed Width
Arms air
Foot Roll
Adjustment
Shoulder
Temperature
ZERO
ZERO
2
"Up & Down" to select,"OK"to confirm.
Auto-Fast
Speed Width
Arms air
Foot Roll
Adjustment
Shoulder
Temperature
Button Description
Legrest up key: Hold down this key, and the legrest will rise slowly;
release it, and the legrest will stop rising. After the leg upward
movement is completed, the legrest will automatically detect the
length of the feet.
Legrest down key: Hold down this key, and the legrest will move
downward slowly; release it, and the legrest will stop downward
movement. After the leg downward movement is completed, the
legrest will automatically detect the length of the feet.
Backrest up button: Hold down the button to make the backrest rise
slowly. Release it to stop such action.
Backrest down button: Hold down the button to make the backrest
move downward slowly. Release it to stop such action.
Linkage sitting key: By holding down this key, the backrest will rise
slowly and the legrest will move downward slowly; by releasing it,
such UP/DOWN action of the backrest and the legrest will be stopped.
After linkage sitting is completed, the legrest will automatically detect
the length of the feet.
Zero Gravity I key: Automatically adjust the legrest and the backrest to
the position for Zero Gravity I.
Zero Gravity II key: Automatically adjust the legrest and the backrest
to the position for Zero Gravity II.
Timing button: This button is used for time adjustment. After it is
pressed every time, the duration will increase by 5 minutes. The total
duration cannot exceed 40 minutes; otherwise, such setting will return
to the minimum time value.
Linkage lying key: By holding down this key, the backrest will move
downward slowly and the legrest will rise slowly; by releasing it, such
DOWN/UP action of the backrest and the legrest will be stopped. After
linkage lying is completed, the legrest will automatically detect the
length of the feet.

2928
Method of Usage
III. Introduction to Armrest Shortcut Keys
1. Power “on/off “button: start or stop massage chair
2. Backrest and footrest lifting & lying button: for adjust the angle of the chair .
3. Footrest lifting& lying button: for adjust the angle of the footrest.
4. Auto : start Auto program
5. Voice control wake up button: press shortly to wake up the chair, press 3 seconds
close or re-start of voice control function
Left armrest Right armrest
USB
AUTO
1
2
3
4
5
6
7
Introduction to the left armrest shortcut keys
6. Pocket : for remote controller and mobile phone
7. USB charge : Recharging mobile phone
Right hand pocket
Method of Usage
IV. Voice Control Instruction
·When the massage chair is turned on or in standby mode, the sound "Hi Alice" or
"Hey Alice"will be produced to enable the voice control function. Alternatively, you
can press the voice control button on the right armrest to enable the voice control
function.
·Long press 3 seconds to turn on or off the voice control function.
·After such function is enabled successfully, the massage chair will reply "I am here."
At this moment, once a corresponding voice control entry to be implemented is
given within six seconds, the corresponding voice control function can be performed
after a reply is received from the massage chair; if no correct voice control entry is
given within six seconds, the voice control function automatically will be off
automatically and needs to be enabled again.
·Note: When waking up the voice control function, please use English, the speech
rate is moderate, Voice commands should be follow up the Voice entry.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
No.
Voice control entry
Massage on
Massage close
Comfort Massage
Relax massage
Full body massage
Neck and shoulder massage
Back and waist massage
Stretch massage
Open the air pressure
Close the air pressure
Up the seat position
Down the seat position
Change the other mode
Go little down
Go little up
Answer entry
Answer: Ok, massage on
Answer: Ok, massage close
Answer: Ok, comfort massage
Answer: Ok, relax massage
Answer: Ok, full body massage
Answer: Ok, neck and shoulder massage
Answer: Ok, back and waist massage
Answer: Ok, stretch massage
Answer: Ok, open the air pressure
Answer: Ok, close the air pressure
Answer: Ok, up the seat position
Answer: Ok, down the seat position
Answer: Ok, change the other mode
Answer: Ok, go little down
Answer: Ok, go little up
Voice Control Entry
Entry: “Hi Alice” or “Hey Alice”. Answer: I am here.
Note: commands 14 and 15 can only be used after command 13.

3130
Method of Usage
1. Enter the smart device main menu. Open "Settings" and select the "Bluetooth"
option. Open "Bluetooth", and Bluetooth will automatically "Search for a New
Bluetooth Device".
2. The smart device will search for the corresponding Bluetooth model (e.g. IMCM-
XXXX). Click the "Match" button. If you are asked whether to match with the
device, you just select "Match" to complete matching.
3. Turn on "Music Player" in the smart device and select the song to play.
·If the power button is pressed during massage, all the massage functions will be
turned off immediately, and the backrest and the footrest will go back to their
default positions. If the massage time is up, all the massage functions will be
turned off immediately, but the backrest and the footrest will not go back to their
default positions.
·Shut off the power supply of this product as shown in the attached figure (Power
Shut-off Diagram of the Product).
V. Turn off the Power and Stop Massage
POWER INPUT POWER INPUT
VI. Operation Instructions for Bluetooth Speaker Play
Power Shut-off Diagram of the Product
Disconnection Diagram
Unplugging Diagram
1 2
VII.Installation Instructions for Legrest
·After connecting the wires and the air hose between the legrest and the massage
chair, remove the cable ties and insert the connecting part into the seat (Figure 1).
·Place the round tubes on the left and right sides of the legrest onto the legrest
support (Figure 2).
Method of Usage
·Next, turn the legrest fixing cover over to cover the round tubes on both sides of
the legrest (Figure 3).
·Fasten the legrest to the massage chair with two M4 screws (one on each side).
Check whether there is any abnormality during turning up and down, or any tube,
cable or wire is folded. If everything is OK, the legrest is installed (Figure 4).
VIII. Instructions for Removal and Use of Head Cushion and Backrest
·The use of the head cushion can reduce the intensity of kneading massage on
the neck and shoulders. You can decide whether to use the head cushion
according to your own needs (the head cushion is recommended). The backrest
and the back cushion are connected by a zipper (1). The head cushion and the
backrest are connected by a hook-and-loop fastener (2).
3 4
12
Zipper Hook-and-loop
fastener

3332
Method of Usage
IX. Floor Protection
·The prolonged heavy pressure on the massage chair may cause scratches on the
floor. Thus, put a carpet or cushion on the floor where the massage chair is placed
to avoid this damage.
Note: Do not move the massage chair with its wheels on the rough ground or in a
narrow space. At least two persons are required to lift it. During lifting, take the
legrest sealing plate and backrest cover grooves as the acting points. (Do not lift the
armrest directly.)
X. Instruction for Movement
·Make sure that all the wires are pulled away from the massage chair surface;
then press the backrest down to a certain angle (with the center of gravity resting
on the wheels), you can push the massage chair forward with hands, move it to a
suitable position and gently restore it to the normal angle. (Note: During
movement, you must turn off the power button first and then unplug the power
cord and the remote controller connection wire).
Warning : The rear moving wheels of the massage chair are only suitable for short-
distance and slow movement. For long-distance transportation, please use other
auxiliary moving tools to move this massage chair!
Product Specification
Model: iComfort Plus
Name: Massage Chair
Rated voltage: 110-120V~ 60Hz
220-240V~ 50Hz/60Hz
Rated power: 150W
Rated time: 20min
Safety structure: Class I
Material description: PVC, PA, steel parts, electric and electron components
MATERIAL PU LEATHER CLOTH WOOD