Itamar Medical WatchPAT Manual

11. In the morning when you wake up, press the
“End Recording” button, and wait a few minutes for
the device to complete the data transmission. After
completing the data transmission you will receive
a thank you message.
12. Remove the chest sensor, probe and WatchPAT®ONE
device. There is no need to keep the device or return it.
You can simply dispose of it.
It is recommended to apply the WatchPAT®ONE device to
your non-dominant hand.
Probe can be worn on any finger, except the thumb.
Before use, remove tight clothes, rings, watches and
other jewelry.
Remove nail polish and artificial nails from the test finger
and make sure the fingernail is cut short.
1. Before you proceed with your sleep study make sure you
have internet access, your phone, WatchPAT®ONE device,
and PIN number.
This guide will take you step by step and show you how to
correctly use the WatchPAT®ONE Home Sleep Apnea Test.
WatchPAT®ONE
Disposable Home Sleep Apnea Test
Step by Step Instructions Guide
3. Open the WatchPAT®ONE application and allow all
permissions required by the application. These
permissions are necessary for the application to operate.
Take out the WatchPAT®ONE from the box. You can click
the “Preview” button on the application to have a quick tour,
showing how to set up the device.
Press “Ready” button when done.
4. Insert the battery into
the WatchPAT®ONE
device.
Press “Next” when done.
5. Remove your watch and
jewelry from your test hand.
Press “Next” when done.
6. Enter the 4-digit PIN code
provided by your physician’s office
or provider, and press “Enter”.
8. Take the chest sensor (snoring and body position sensor)
and direct the cable in through your sleeve
and out through the neck opening.
Remove the tab from the sticker and
attach the sensor just below your
sternal notch.
Press “Next” when done.
7. Put the WatchPAT®ONE device
on your non-dominant hand.
Ensure it is not too tight
and not too loose.
Press “Next” when done.
9. Place the probe all the way onto a finger of your
non-dominant hand. You may use any finger except
the thumb. The probe should be inserted
so the sticker marked TOP is positioned
above the fingernail. Hold the probe
against a hard surface and slowly
pull the TOP tab towards you to
remove it from the probe.
Press “Next” when done.
Now click the “Start” button to begin your sleep study.
10. You are all set.
Last few steps before you begin your sleep study:
a. Make sure your phone is located no more than
15 feet/5 meters from the WatchPAT®ONE device.
b. Turn off all other transmitting devices in the room,
such as other smart phones, smart watches and
headphones, as they could interfere with the test.
c. Connect your phone to the charger, it must remain
plugged in throughout the night. If you need to get up
during the night leave the phone plugged in, no need
to carry it with you.
Before applying WatchPAT®ONE:
Note: Use only Alkaline AAA battery.
Do not insert the battery until you are ready to go to bed.
START
END RECORDING
NEXT
NEXT
ENTER
NEXT
NEXT
NEXT
READY
PREVIEW
WatchPAT® ONE Internet Access
Phone PIN Number
1
2
Ba�ery
2. Download the WatchPAT®ONE application to your mobile
device (available on Apple App Store
and Google Play Store).
ENTER PIN
Enter your assigned four digit PIN
(personal identification number) and tap ENTER
1
2
CLOSE APPLICATION
Once received press “Close Application”.
* If your WatchPAT®ONE device does not
include the chest sensor, skip this step.

If you have any questions
you may contact
Itamar®Medical Help Desk at:
1-888-748-2627
Step by Step Instructions Guide
Scan the QR code below to download
the WatchPAT®ONE Application
For step-by-step video instruction
please visit
watchpatone-howtouse.com
Disposable Home Sleep Apnea Test
®
Disposable Home Sleep Apnea Test
For step-by-step video instruction
Visit watchpatone-howtouse.com
REF OM2193390 -Ed.2
Caution: Federal Law Restricts this device to sale by or on
the order of a licensed healthcare practitioner
Single use, do not re-use
Temperature limit 0
o
C - 40
o
C
Refer to instruction for use
Federal communications commision identification number
2APUBWPONE
FCC ID
Battery operating voltage
Ingress protection
Type BF applied part
only
Date of manufacture
Use-by date
SN
Medical device manufacturer
Catalogue number
Serial number
REF
Fragile, Handle with care
Keep dry
The product is marked with the CE logo 2797 for BSI
Authorized representative in the European Community
EC REP
According to the WEEE Directive 2012/19/EU, all waste
electrical and electronic equipment (EEE) should be collected
separately and not disposed of with regular household waste.
Please dispose this product and all of its parts in a
responsible and environmentally friendly way.
Technical InformationLabeling
IP22
1.5V DC
Important Notes:
• Storage andoperation
temperatures
0
o
C - 40
o
C
• Do not attempt to connect or
disconnect any part of the unit.
• Do not try to introduce any
foreign object into the unit.
• Do not, under any
circumstances, attempt to fix a
problem by yourself.
The Squaire 12,Am Flughafen
60549 Frankfurtam Main
Germany
Arazy Group Gmbh
EC REP
9 Halamish Street, PO box 3579
Caesarea Ind. Park, 3088900 Israel
T: [phone],F: [phone]
Itamar Medical Ltd.
•The WatchPAT
®
ONE should not
cause any discomfort or pain.
Should you encounter unbearable
discomfort, remove the device
and call the help desk.
www.itamar-medical.com
®
®
www.itamar-medical.com
®