jablotron Mercury User manual

EN
1
MMD510307
JABLOTRON Mercury
Thank you for purchasing a JABLOTRON Mercury system. This user manual will guide you and
explain everything you need to operate the system.
PEACE OF MIND AND SAFETY
If the alarm is to truly assure protection, it must be connected to an alarm receiving centre (ARC) to
ensure professional intervention in the event of danger. If you do not utilize an ARC service, please
contact your Installation Partner.
HOW TO ARM AND DISARM THE SYSTEM
Fire, flooding and tampering detection is permanent, intrusion detectors monitor only if the
system is armed.
The garage door and entrance gate may be controlled by the alarm system through the means of
additional output modules.
The doorbell function is available if the system has a doorbell button enrolled during configuration.
Depending on your system setup, use:
REMOTE CONTROL
Subject to how the alarm system is configured, the remote control allows the user to arm and/or
disarm the entire alarm system or its sections.
KEYPAD WITHOUT A DISPLAY
Depending on how the alarm system was configured during installation, the keypad arms or
disarms the entire alarm system or its part.
AUTHORIZATION: You must always enter your valid access code or use an RFID tag/card on the
keypad before using the ARM or DISARM buttons. The validity of the authorization is indicated by
the green flashing of the indication light bar.
ALARM CANCELLATION:press DISARM
HIGH-QUALITY
ALARM
PROFESSIONAL
INSTALLATION
MONITORING
24H A DAY
ACTION IN CASE
OF AN ALARM
OPEN
THE GARAGE
OPEN
THE GATE
M
C
AN
C
ELLATI
O
N
:
p
r
ess
D
Red – arm
Green – disarm
Yellow – out of range
Red – arm
Green – disarm
Yellow – out of range
DISARM DISARMARM ARM

User manual - JABLOTRON Mercury
2
MMD510307
PARTIAL SETTING: If your alarm has a partial setting enabled, only selected detectors are armed.
It‘s activated by authorizing and pressing the ARM button (confirmed by the yellow LED indicator on
the right button). If the keypad is configured to allow full arming, it is activated by double-pressing
the ARM button after a valid authorization (confirmed by the red LED indicator on the right button ).
ENTRY AND EXIT DELAY: Is indicated by the keypad beeping. Exit time is the time frame during
which you must vacate the premises of the protected area before the system becomes armed.
Entry time is the time frame during which you must disarm the alarm system, otherwise an alarm
is triggered. The specific times are configured by your JABLOTRON Installation Partner.
ALARM CANCELLATION: Authorize yourself and press the DISARM button.
ALARM MEMORY: The red LED remains flashing after an alarm event. To cancel this indication,
repeat the disarming (by authorizing and pressing the DISARM button).
KEYPAD WITH A DISPLAY
It allows the user to control up to 4 independent sections of the house. In addition, it features
aMENU that can be used to view the event memory and other information.
AUTHORIZATION: You must always enter your valid access code or use an RFID tag/card on the
keypad before using the ARM or DISARM buttons. The validity of the authorization is confirmed by the
green flashing of the light bar.
PARTIAL SETTING: if your alarm utilizes partial setting in any section, it is activated by authorizing
and pressing the corresponding ARM button (the yellow LED on the right). Pressing the ARM
button twice after authorization will fully arm the section (red LED on the right).
ENTRY AND EXIT DELAY: Indicated by the keypad beeping. Exit time is the time frame during
which you must vacate the premises of the protected area before the system becomes armed.
Entry time is the time frame during which you must disarm the alarm system, otherwise an alarm is
triggered. The specific times are configured by your JABLOTRON Installation Partner.
ALARM CANCELLATION: Authorize yourself and press the DISARM button, which is flashing red.
ALARM MEMORY: The red LED remains flashing after an alarm event. To cancel this indication,
repeat the disarming (by authorizing and pressing the DISARM button).
INTERNAL KEYPAD MENU
−EVENT MEMORY – overview of the history recorded in the alarm
−SYSTEM STATUS – overview of alarm and device status
−DISPLAY OPTIONS* – display contrast and backlight
* this setting is available only to the alarm administrator.
DI
SP
LA
Y
tl t4id d t ti fthh
Green – disarmed
Green flashing –
entry delay
Green – everything is OK
Green flashing –
valid authorization
Red flashing – alarm
(or alarm memory)
Yellow – fault
Yellow – Partial setting
Red – armed
Red flashing – alarm
(or alarm memory)
DISARM button ARM button

EN
3
MMD510307
Green – disarmed
Green flashing –
exit delay
Green – everything is OK
Green flashing –
valid authorization
Red flashing – alarm
(or alarm memory)
Yellow – fault
Yellow – Partial setting
Red – armed
Red flashing – alarm
(or alarm memory)
The ARM button for
individual sections
ed
–
h
ing is
OK
–
t
io
n
a
larm
o
ry
)
Yello
w –
Pa
R
Red
fl
as
h
(
or ala
The
AR
ind
ivi
d
The names of the
sections, or system
status information.
The DISARM button
for individual sections
Note: in order to prolong the battery life, the wireless keypad turns off after approximately 10
seconds of inactivity.
MyJABLOTRON APP
The smartphone app allows you to control and monitor your alarm, open
your garage door and entrance gate. It contains a history of events and,
and if motion detectors with photo-verification cameras are installed,
displays alarm photos in the Gallery tab. It also reports selected event
types. The alarm administrator can set different permissions for individual
users. Depending on the type of phone, the user is authorized by a numeric
code, fingerprint or facial recognition.
The MyJABLOTRON app can be downloaded for both iOS and Android.
The access account for the alarm administrator is set by the Installation
Partner. You will receive the login details for the app on the email address
you provide to the JABLOTRON Installation Partner. The alarm administrator
then may set access to the app for other users.
The best way to familiarize yourself with the app is to browse through the options one by one.
ALARM MAINTENANCE
For reliable alarm system operation, we recommend that you arrange regular annual inspections
of your system with your JABLOTRON Installation Partner. Please contact your JABLOTRON
Installation Partner if the alarm reports a malfunction.
Warning:
1. Do not attempt to open or disassemble any component of the alarm system. A tamper alarm will
occur.
2. When cleaning, prevent damaging the alarm system components. We suggest cleaning dust
buildup from the detectors with a fine fiber duster.
3. Use a damp cloth to clean the keypad. Make sure to avoid using organic solvents as their use could
potentially damage the keypad.
4. Battery replacement is to be carried out solely by your JABLOTRON Installation Partner.
Theaverage battery lifetime is approximately 2 years. The battery lifetime of a wireless keypad may
be significantly shorter if the keypad is used more than twice a day.

User manual - JABLOTRON Mercury
4
MMD510307
CONTACT TO YOUR JABLOTRON INSTALLATION PARTNER
Digital manual
version
CONTROL PANEL TECHNICAL PARAMETERS
PARAMETER TYPE: CU2202MD
Dimensions 268 x 225 x 83 mm
Nominal control panel voltage / frequency /
fuse
~110–230 V/50–60 Hz, max. 0,28 A
with a fuse F1,6 A/250 V, protection class II
Electrical input power / current max 23 VA / 0,1 A
Classification of alarm device Security grade 2 / environment class II
@ according to standards EN50131-1, EN 50131-3, EN 50131-6,
EN 50131-5-3 (utilizing a radio module),
EN 50131-10, EN 50136-1, EN 50136-2
@ environment Indoor general
@ operational range of temperature / humidity -10 °C to +40 °C/ 75% RH w/o condensation
Number of code combinations per user, there
are no disallowed codes in the alarm
104– (The number of users within a system – 1)
Number of code combinations per user when
using access cards
109card codes
EMC EN 50130-4, EN 55032, ETSI EN 301 489-1,
ETSI EN 301 489-3
Electrical safety EN IEC 62368-1
Power supply protection Fuse T1,6 A; 250 V
Backup battery Lead 12 V / 2,6 Ah
Certification body TREZOR TEST (no. 3025)
JABLOTRON ALARMS a.s. hereby declares that the CU2202MD is in a compliance
with the relevant Union harmonization legislation: Directives No: 2014/53/EU, 2014/35/
EU, 2014/30/EU and 2011/65/EU. The original of the conformity assessment can be
found at www.jablotron.com - Section Downloads.
Note: Disposing of this product correctly will help save valuable
resources and prevent any potential negative effects on human
health and the environment, which could otherwise arise from
inappropriate waste handling. Please return the product to the
dealer or contact your local authority for further details of your
nearest designated collection point.
JABLOTRON ALARMS a.s. | Pod Skalkou 4567/33 | 46601 Jablonec n. N. | Czech Republic | www.JABLOTRON.com