Jacto Condorito User manual

105 Gal 30
’
3 point mounted Boom Sprayer
105
Gal
.
30
3
point
mounted
Boom
Sprayer

The
Condorito
arrives in
three crates
0
” 84 lbs
Unit (left)
x
10” x 1
0
Unit
(left)
Booms (Left,
Ri
g
ht & Center
)
103”
x
g)
53” x 42” x 45” 333 lbs
Center spray boom
support section
80” x 7” x 29” 60 lbs
Total shipping weight 477 lbs

When removing the unit from the shipping crate, be
cautious of some crate boards going through the unit
chassis.
Use a
Crow Bar
to
to
Dismantle
crates.

Remove the Control Valve from
it’s shipping position (on the
chassis just above the filter).
Move it around to the
front of the unit
front
of
the
unit
Mount it with the two
Mount
it
with
the
two
(2) 5/16” bolts, lock
washers & nuts,
hi h ill b th
w
hi
c
h
w
ill
b
e on
th
e
front mounting plate.

Connect the Bypass Hose from the control valve
to the top of the main tank.

Select the height of the sprayer
boom by attaching the center
boom support section to the
boom
support
section
to
the
corresponding bolt holes on
the rear of the chassis.
Attach the
center support
section using
the four (4) 3/8
”
the
four
(4)
3/8
bolts, washers,
and nuts, which
ill b i th
w
ill
b
e
i
n
th
e
accessories box.

The center
The
center
boom section
attaches to
th b
th
e
b
oom
support
section with
four (4) bolts,
washers, and
nuts which
nuts
which
should be on
the center
boom section
boom
section
when
unpacking.

We recommend
We
recommend
using zip ties to
anchor the
htth
h
ose
t
o
th
e
boom support.
Route the two (2) chemical hoses from the control
valve across the top of the tank, and connect to each
respective half of the chemical circuit on the center
respective
half
of
the
chemical
circuit
on
the
center
section. Tighten each with the hose clamp provided.

Each boom will be labeled Left or Right

Position each boom onto the post of the center
section and attach using the following configuration
section
and
attach
using
the
following
configuration
.
Ctt Pi
B St bili
Two (2) small washers
C
o
tt
er
Pi
n
Four (4) small washers
B
oom
St
a
bili
zer
Two (2) nuts, tighten
the first nut snuggly,
the second nut is to
lock it down
Two (2) large washers
lock
it
down
.
Spring

Connect
chemical
hoses from
each boom
each
boom
section to the
ends of the
t
cen
t
er
section.
Ti
g
hten usin
g
gg
the hose
clamp.
Fold over the outer boom segment, then
rotate the boom backward and up to the
rotate
the
boom
backward
and
up
to
the
mounting

Fold each boom up to lock into boom support mount. If the posts
do not align correctly adjust the boom
’
s locking piece
do
not
align
correctly
,
adjust
the
boom s
locking
piece
.
(To adjust
th h l
th
e
h
o
l
e
position to
mate
smoothly
smoothly
to the post
loosen the
circled
circled
bolts and
slide the
lockin
g
g
piece into
position).

Cut the two (2) zip ties holding the pump
to the side of the chassis. The Safety Chain
affixed to the
affixed
to
the
pump should be
attached to the
chassis side to
chassis
side
to
prevent the pump
from knocking
around.
The coupling sleeve of the
pump would rest on the
p
ost
p
rovided on the
pp
chassis when not
connected to the tractor.
(See Page 22
-
23 of the Operators
(See
Page
22
23
of
the
Operators
Manual for connecting the pump to the
PTO shaft).

Affix the twenty
-
one
Affix
the
twenty
-
one
(21) nozzles to the
boom.
Connect the
Connect
the
Condorito sprayer
to the tractor’s
three
-
point
three
point
suspension
(See pages 20 – 24
of the Operator’s
Manual).