Jacto J-1000 User manual

J-1000 is shipped in three crates
66” x 42” x 22” 506 lbs
Notice each
crate has Serial
Number. When
assembling
multiple units
insure to match
In the smaller crate the axle and tires
insure
to
match
SN’s on the
crates.
can be found below the bumper.
40
”
x40
”
x40
”
417 lbs
40
x
40
x
40
417
lbs

Hoist the front of sprayer at the chassis.
Attach the jack support to the front of the
Step One: Attach front jack support and tires to the axle. . .
Attach
the
jack
support
to
the
front
of
the
chassis using the pin and cotter key set
provided with it.
Insert the retaining pin with the jack in the
Insert
the
retaining
pin
with
the
jack
in
the
upright position as shown below.
Secure a tire to each end of the axle using the
12 lug nuts provided.

Hoist the rear of sprayer at the chassis.
Position the axle with tires into position
Step Two: Slide the crate bottom out and move the tires/axle in. . .
Position
the
axle
with
tires
into
position
under the sprayer. Place the spacer between
the chassis and the axle. Secure using the
four bolts, lock washers, and nuts provided in
ib
accessor
i
es
b
ox.
The tracking axle linkage will attach
hltthihldbfi
h
ere
l
a
t
er,
thi
s s
h
ou
ld
b
e
f
ac
i
ng
forward on the right side of the
sprayer.

Step Three: Attach tongue and tank sump protective cover. . .
Using the two long pin
and cotter key sets.
Attach the tongue to the
bottom front of the
sprayer.
sprayer.
Insert the rear pin first (as the
hole is slotted).
Using the four bolts, washers, and nuts
id d th t k t ti
prov
id
e
d
secure
th
e
t
an
k
sump pro
t
ec
ti
ve
cover to the tongue.

Step Four: Attach draw bar and tie rod to tracking axle. . .
Slide the draw bar into the tongue,
secure with washer, castle nut and
tt i
Straighten up the tires.
Rotate the tie rod clockwise
co
tt
er p
i
n.
Rotate
the
tie
rod
clockwise
to connect to tracking axle
linkage.
Adjust the distance of the tie rod so
that the draw bar is squared. Use the
nuts on the tie rod to tighten into
nuts
on
the
tie
rod
to
tighten
into
position. After connecting the rear of the tie rod
to the tracking axle and the draw bar is
s
q
uare, then connect the tie rod to the
q
drawbar using the pin & cotter set.
1 - adjusts tracking axle
2 - adjusts wheel alignment

Step Five: Prepare chemical hose. . .
Remove the two wing nuts and
washers (one on each side) and lift
ff f t h d
o
ff
f
ron
t
h
oo
d
.
Unwrap all hoses and route them
through the opening in the front of
the hood. The black hose must be
connected securely to the top/front
of the pump.
Replace the front hood.

Step Six: Install the chemical control valve. . .
Affix the Control Valve Mount to the
front of the chassis using the two (2)
front
of
the
chassis
using
the
two
(2)
bolts provided.
Attach the Control Valve to the
Attach
the
Control
Valve
to
the
mount using the two (2) bolts &
nuts provided. Also, attach the
chemical line as shown.
Attach the chemical line as shown.

Step Six: Install the chemical control valve (continued). . .
Notice the lower
connection for Black
Attach the Blue (chemical
bypass) hose to the upper port
b lli t th t i
connection
for
Black
chemical hose from the
pump uses two (2)
retainers.
b
y pu
lli
ng ou
t
th
e re
t
a
i
ner,
pushing in hose connector and
replacing retainer.
Pushed In
Pulled Out
Connect the chemical hoses.

Step Seven: Install PTO and drive shaft cover. . .
Slide the PTO onto the drive shaft
then secure with the nut and bolt.
Then slide the drive shaft cover over
the PTO.
Secure the drive shaft cover in place
ithtblt iddith
us
i
ng
th
e
t
wo
b
o
lt
s prov
id
e
d
i
n
th
e
front of the chassis.