Jetter JX3-BN-ETH User manual

User Manual
JX3-BN-ETH
We automate your success.

Jetter AG
Graeterstrasse 2
71642 Ludwigsburg
Germany
Phone
Switchboard [phone]
Sales [phone]
Technical Hotline [phone]
E-mail
Technical Hotline [email protected]
Sales [email protected]
Translation of the german original User
Manual
Revision 1.20.1
Date of issue 8/20/2020
This document has been compiled by Jetter AG with due diligence, and based on the known
state of the art. Revisions and further development of our products are not automatically
mentioned in a reviewed document. Jetter AG shall not be liable for errors in form or content,
or for missing updates, as well as for damages or disadvantages resulting from such failure.

Jetter AG Table of Contents
JX3-BN-ETH User Manual iii
Table of Contents
1 Introduction .....................................................................................................................................6
1.1 Information on this document .................................................................................................. 6
1.2 Typographical conventions......................................................................................................6
2 Safety ...............................................................................................................................................7
2.1 General information.................................................................................................................7
2.2 Purpose ...................................................................................................................................7
2.2.1 Intended use................................................................................................................7
2.2.2 Usage other than intended ..........................................................................................7
2.3 Warnings used in this document ............................................................................................. 8
3 Product description ........................................................................................................................9
3.1 Design .....................................................................................................................................9
3.2 Features ..................................................................................................................................9
3.3 Status indication ....................................................................................................................10
3.3.1 Diagnostics capabilities by means of status indication..............................................10
3.4 Nameplate .............................................................................................................................11
3.5 Scope of delivery...................................................................................................................11
4 Technical specifications...............................................................................................................12
4.1 Dimensions............................................................................................................................12
4.2 Mechanical specifications......................................................................................................12
4.3 Electrical properties...............................................................................................................13
4.3.1 System power supply ................................................................................................13
4.4 Environmental conditions ...................................................................................................... 14
4.5 EMI values.............................................................................................................................14
4.5.1 Housing .....................................................................................................................14
4.5.2 Shielded data and I/O lines .......................................................................................15
4.5.3 DC power supply inputs and outputs.........................................................................16
5 Mechanical installation.................................................................................................................17
5.1 Installing the device on the DIN rail....................................................................................... 17
5.2 Removing the device from the DIN rail.................................................................................. 18
5.3 Dismounting the enclosure from the backplane module ....................................................... 19
6 Electrical connection ....................................................................................................................20
6.1 Improving the noise immunity................................................................................................21
6.2 Ports and interfaces .............................................................................................................. 22
6.2.1 Terminal X10 - Power supply ....................................................................................22
6.2.1.1 2-pin connector, spring-cage technology.......................................................22
6.2.2 Ports X14, X15 - Ethernet .........................................................................................23

Table of Contents Jetter AG
iv JX3-BN-ETH User Manual
6.3 Commissioning......................................................................................................................24
6.3.1 LED states during the boot process ..........................................................................25
7 Programming.................................................................................................................................26
7.1 Abbreviations, module register properties and formats......................................................... 26
7.2 Addressing of I/O expansion modules...................................................................................27
7.2.1 Numbering registers and I/Os ...................................................................................28
7.2.1.1 Expansion modules connected with a controller ...........................................28
7.2.1.2 Expansion modules connected to an Ethernet bus node ..............................29
7.3 Operating system .................................................................................................................. 31
7.3.1 Updating the operating system of a bus node...........................................................31
7.3.1.1 Operating system update by means of the IDE.............................................31
7.3.1.2 Operating system update via FTP .................................................................32
7.4 File system ............................................................................................................................ 33
7.4.1 Properties ..................................................................................................................33
7.4.1.1 Flash disk - Properties...................................................................................33
7.5 Identification ..........................................................................................................................34
7.5.1 Electronic Data Sheet (EDS).....................................................................................34
7.5.1.1 EDS file "eds.ini"............................................................................................34
7.5.1.2 EDS registers ................................................................................................35
7.5.2 Revisions...................................................................................................................36
7.5.2.1 Hardware revisions........................................................................................36
7.5.2.2 Operating system version..............................................................................37
7.6 IP configuration ..................................................................................................................... 38
7.6.1 Factory settings .........................................................................................................38
7.6.2 Configuration memory ...............................................................................................39
7.6.3 Configuration file "config.ini"......................................................................................40
7.6.3.1 Section [IP] ....................................................................................................40
7.6.3.2 Section [HOSTNAME] ...................................................................................41
7.6.3.3 Section [PORTS] ...........................................................................................42
7.6.3.4 Changing the IP configuration via the configuration file ................................42
7.6.4 Configuration registers ..............................................................................................43
7.6.5 Setting the IP address of the bus node .....................................................................44
7.6.5.1 Setting the default IP address .......................................................................45
7.6.5.2 Setting the IP address via configuration file ..................................................45
7.6.5.3 Setting the IP address via configuration file and DIP switch .........................46
7.6.5.4 Setting the IP address during runtime ...........................................................47
7.6.6 Using names for IP addresses ..................................................................................48

Jetter AG Table of Contents
JX3-BN-ETH User Manual v
7.7 Storage options - Overview ................................................................................................... 50
7.7.1 Operating system memory ........................................................................................50
7.7.2 File system memory ..................................................................................................50
7.7.3 Special registers........................................................................................................51
7.7.4 Inputs and outputs.....................................................................................................51
7.8 Ethernet system bus..............................................................................................................52
7.9 FTP server.............................................................................................................................53
8 Registers - Overview.....................................................................................................................54
9 Maintenance and repairs ..............................................................................................................61
9.1 Maintenance, repairs and disposal........................................................................................61
9.2 Storage and shipment ........................................................................................................... 61
10 Service ...........................................................................................................................................62
10.1 Customer service .................................................................................................................. 62
11 Spare parts and accessories .......................................................................................................63
11.1 Spare parts............................................................................................................................63
11.2 Accessories ...........................................................................................................................63
11.2.1 Ethernet/EtherCAT® cable........................................................................................63

Jetter AG Introduction | 1
JX3-BN-ETH User Manual 6 / 64
1 Introduction
1.1 Information on this document
This document forms an integral part of the product and must be read and under-
stood prior to using it. It contains important and safety-related information for the
proper use of the product as intended.
Target groups This document is intended for specialists with appropriate qualifications.
Only competent and trained personnel is allowed to put this device into operation.
During the whole product life cycle, safe handling and operation of the device
must be ensured. In the case of missing or inadequate technical knowledge or
knowledge of this document any liability is excluded.
Availability of
information
Make sure this document is kept at the ready in the vicinity of the product
throughout its service life.
For information on new revisions of this document, visit the download area on our
website. This document is not subject to any updating service.
Start | Jetter - We automate your success.
For further information refer to the following information products:
■Version updates
Information about new versions of software products or of the operating sys-
tem of your controller.
■JetSym software Online Help
Detailed description of software functions with application examples
■Application-oriented manuals
Cross-product documentation
1.2 Typographical conventions
This manual uses different typographical effects to support you in finding and
classifying information. Below, there is an example of a step-by-step instruction:
üThis symbol indicates requirements which have to be met before executing
the following action.
►This sign or a numbering at the beginning of a paragraph marks an action in-
struction that must be executed by the user. Execute the instructions one after
the other.
ðThe target after a list of instructions indicates reactions to, or results of these
actions.
INFO In the info box you will find helpful information and practical tips about your prod-
uct.

Jetter AG Safety | 2
JX3-BN-ETH User Manual 7 / 64
2 Safety
2.1 General information
At the time of placing on the market, this product corresponds to the current state
of the art and meets the recognized safety rules.
Besides this user manual, laws and regulations in the operator's country are rele-
vant to the operation of the product. The operator is responsible for complying
with the directives mentioned below:
■Applicable legislation, rules, and regulations
■Relevant accident prevention regulations
■Accepted safety rules
■EU directives and other country-specific regulations
2.2 Purpose
2.2.1 Intended use
The Ethernet bus node JX3-BN-ETH is intended for the extension of existing con-
trol systems in machines. This device is used to control machinery, such as con-
veyors, production machines, and handling machines.
Operate the device only in accordance with the intended conditions of use, and
within the limits set forth in the technical specifications.
Intended use of the product includes its operation in accordance with this man-
ual.
SELV The operating voltage of this device is classified as Safety Extra Low Voltage and
is therefore not subject to the European Low Voltage Directive. The device may
only be operated from a SELV source.
2.2.2 Usage other than intended
This device must not be used in technical systems which to a high degree have
to be fail-safe.
Machinery Directive This device is no safety-related part as per Machinery Directive 2006/42/EC, and
must, therefore, not be used for safety-relevant applications. This device is NOT
intended for the purpose of personal safety, and must, therefore, not be used to
protect persons.

Jetter AG Safety | 2
JX3-BN-ETH User Manual 8 / 64
2.3 Warnings used in this document
DANGER High risk
Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING Medium risk
Indicates a potential hazardous situation which, if not avoided, could result in
death or serious injury.
CAUTION Low risk
Indicates a hazardous situation which, if not avoided, could result in minor or
moderate injury.
NOTICE Material damage
Indicates a situation which, if not avoided, could result in malfunctions or material
damage.

Jetter AG Product description | 3
JX3-BN-ETH User Manual 9 / 64
3 Product description
The Ethernet bus node JX3-BN-ETH lets you set up remote I/O stations. It com-
prises a JX3 bus master to which up to 16 JX3 I/O modules can be directly con-
nected. The bus node enables fast cyclic communication between controllers and
the remote I/O station via Ethernet.
3.1 Design
1
8
7
2
3
4
5
62
Fig.1: Device configuration
1Status indication 2DIN rail latch
3Housing 4Backplane module
5Connector X119:
Connector for JX3 I/O modules 6DIN rail release latch
7Terminal X10:
Power supply 8Sockets X14, X15: Ethernet interface
3.2 Features
■Ethernet bus node for a maximum of 16 JX3 I/O modules
■Fast I/O processing
■Integrated 2-port switch
■Choice of static or dynamic IP address assignment via GNN (Global Node
Number)
■Synchronous Ethernet protocol between controller and JX3-BN-ETH
■Power supply for up to 8 JX3 modules

Jetter AG Product description | 3
JX3-BN-ETH User Manual 10 / 64
3.3 Status indication
LEDs indicate the communication status of the device as well as the status of the
power supply.
R E D1 D2
Fig.2: Status indication
LED Description LED Description
R State of operating system D1 Special states
E Generic error D2 State of boot loader
3.3.1 Diagnostics capabilities by means of status indication
The color and status of the LEDs provide diagnostic options for various states. In
the JetSym application software, diagnostics can be performed in the hardware
manager or via the setup window by entering the corresponding register number.
LED Status Color Description
R OFF --- No power supply or failure
Blinking at 1
Hz
Green Module is booting
Blinking at 4
Hz
Green Reset or fatal error
ON Green Normal operating condition
E OFF --- No error
Blinking at 1
Hz
Red There is no valid OS
Blinking at 4
Hz
Red Reset or fatal error
ON Red Error; refer to error register
D1 OFF --- Normal operating condition
Blinking at 1
Hz
Red Automatic IP configuration
Blinking at 4
Hz
Red Reset or fatal error
D2 OFF --- Boot loader is not running
Blinking at 1
Hz
Red Automatic IP configuration
Blinking at 4
Hz
Red Reset or fatal error
ON Red Boot loader is being executed

Jetter AG Product description | 3
JX3-BN-ETH User Manual 11 / 64
3.4 Nameplate
63
12
5 4
Fig.3: Sample nameplate
1Company logo 2Serial number
3Certification mark 4Item number
5Hardware revision 6Item name
3.5 Scope of delivery
Scope of delivery Item number Quantity
JX3-BN-ETH 10000645 1
Male connector in spring-cage technology,
2-pin
60870409 1
Terminal labels 60870411 10
Installation manual 60873376 1

Jetter AG Technical specifications | 4
JX3-BN-ETH User Manual 12 / 64
4 Technical specifications
This chapter contains information on electrical and mechanical data, as well as
on operating data of the JX3-BN-ETH.
4.1 Dimensions
96
64
132
50
56.3
Fig.4: Dimensions in mm
4.2 Mechanical specifications
Category Description Standards
Weight 250 g
Enclosure specifications
Material Plastic
Maximum height of fall
Units within packing 1 m DIN EN 61131-2
DIN EN 60068-2-31
Units within product pack-
aging
0.3 m
Vibration resistance
Frequency sweeps 1 octave/minute,
sinusoidal
DIN EN 61131-2
DIN EN 60068-2-6
Constant amplitude 3.5 mm 5 Hz ≤ f ≤ 9 Hz
Constant acceleration 1 g 9 Hz ≤ f ≤ 150 Hz
Number and direction 10 sweeps for all 3 spatial axes
Shock resistance
Type of shock Half-sine wave DIN EN 61131-2
DIN EN 60068-2-27
Intensity and duration 15 g for 11 ms
Number and direction 3 shocks in the directions of all 3 spatial axes

Jetter AG Technical specifications | 4
JX3-BN-ETH User Manual 13 / 64
Category Description Standards
Degree of protection
Degree of protection IP20 DIN EN 60529
Tab.1: Mechanical specifications
4.3 Electrical properties
Power supply
(terminal X10)
Category Description
Supply voltage DC 24 V
Permissible voltage range -15 % ... +20 %
Reach Supply of the bus node and a maximum of 8 con-
nected expansion modules
Input current 1.0 A max.
Power consumption 24 W max.
Tab.2: Power supply (terminal X10)
Ethernet
(sockets X14, X15)
Category Description
Terminal type RJ45 jack
Number of ports 2
1 port per terminal
Bit rate 10 Mbit/s, 100 Mbit/s (Cat 5e)
Auto-crossover Yes
Tab.3: Ethernet (sockets X14, X15)
Memory
configurations
Category Description
Flash disk 4 MB
Tab.4: Memory configurations
Electrical
Safety
Category Description Standards
Class of protection III DIN EN 61131-2
Dielectric test voltage Functional ground is con-
nected to chassis ground
internally.
Protective connection 0
Overvoltage category II
Tab.5: Electrical safety
4.3.1 System power supply
Fhe bus node supplies the system bus with logic and power supply voltage.
These two types of voltage are for supplying the connected expansion modules.
System bus Category Description
Bus type JX3 system bus
Logic voltage
Supply voltage DC 5 V
Permissible voltage range -15 % ... +10 %
Additional voltage
Supply voltage DC 24 V
Permissible voltage range -24 % ... +20 %
Tab.6: System bus

Jetter AG Technical specifications | 4
JX3-BN-ETH User Manual 14 / 64
Expansion modules Category Description
Logic voltage
Current consumption I5V = max. 1,200 mA
Power consumption 6 W max.
Additional voltage
Current consumption I24 V = max. 750 mA
Power consumption 18 W max.
Tab.7: Expansion modules connected to the system bus
4.4 Environmental conditions
Category Description Standards
Operating temperature 0 … +50 °C DIN EN 61131-2
Storage temperature -40 … +70 °C DIN EN 60068-2-1
Air humidity 10 … 95 %
non-condensing
DIN EN 60068-2-2
Max. operating altitude: 2,000 m above sea level
Corrosion immunity and
chemical resistance
No special protection against corrosion. Ambient air
must be free from higher concentrations of acids, al-
caline solutions, corrosive agents, salts, metal va-
pors, and other corrosive or electroconductive con-
taminants.
Degree of pollution - Elec-
tronics
Degree of pollution 2 DIN EN 61131-2
Usually, the pollution is non-conductive. However,
temporary conductivity due to condensation may oc-
cur.
Tab.8: Environmental conditions
4.5 EMI values
4.5.1 Housing
Emitted interfer-
ence
Parameter Values Standards
Frequency band 30 … 230 MHz DIN EN 61000-6-3
DIN EN 61131-2
DIN EN 55011
Limit value 30 dB (µV/m) at 10 m dis-
tance
Frequency band 230 … 1,000 MHz
Limit value 37 dB (µV/m) at 10 m dis-
tance
Class B
Tab.9: Emitted interference
Immunity to inter-
ference
Parameter Values Standards
Magnetic field with mains frequency
Frequency 50 Hz DIN EN 61131-2
DIN EN 61000-6-2
DIN EN 61000-4-8
Magnetic field 30 A/m

Jetter AG Technical specifications | 4
JX3-BN-ETH User Manual 15 / 64
Parameter Values Standards
RF field, amplitude-modulated
Frequency band 80 MHz … 2 GHz DIN EN 61131-2
DIN EN 61000-6-2
DIN EN 61000-4-3
Test field strength 10 V/m
AM 80 % with 1 kHz
Criterion A
ESD
Discharge through air
Test peak voltage 6 kV
8 kV DIN EN 61131-2
DIN EN 61000-6-2
DIN EN 61000-4-2
Contact discharge
Test peak voltage 6 kV
4 kV
Criterion A
Tab.10: Immunity to interference
4.5.2 Shielded data and I/O lines
Immunity to inter-
ference
Parameter Values Standards
RF field, asymmetric, amplitude modulated
Frequency band 0.15 … 80 MHz DIN EN 61131-2
DIN EN 61000-6-2
DIN EN 61000-4-6
Test voltage 3 V
AM 80 % with 1 kHz
Source impedance 150 Ω
Criterion A
Bursts
Test voltage 1 kV DIN EN 61000-6-2
DIN EN 61000-6-2
DIN EN 61000-4-4
tr/tn 5/50 ns
Repetition frequency 5 kHz
Criterion A
Surge voltages, asymmetric, line to earth
Common-mode interfer-
ence
tr/th 1.2/50 µs DIN EN 61131-2
DIN EN 61000-6-2
DIN EN 61000-4-5
1 kV
Tab.11: Immunity of shielded data and I/O lines
Interference immu-
nity - Functional
earth connection
Parameter Values Standards
RF field, asymmetric, amplitude modulated
Frequency band 0.15 … 80 MHz DIN EN 61131-2
DIN EN 61000-6-2
DIN EN 61000-4-6
Test voltage 3 V
AM 80 % with 1 kHz
Source impedance 150 Ω
Criterion A
Bursts
Test voltage 1 kV DIN EN 61000-6-2
DIN EN 61000-6-2
DIN EN 61000-4-4
tr/tn 5/50 ns
Repetition frequency 5 kHz
Criterion A
Tab.12: Interference immunity - Functional earth connection

Jetter AG Technical specifications | 4
JX3-BN-ETH User Manual 16 / 64
4.5.3 DC power supply inputs and outputs
Emitted interfer-
ence
Parameter Values Standards
Signal and control line connections, DC voltage supply inputs and - out-
puts
Frequency band 0.15 … 0.5 MHz DIN EN 61000-6-3
Limit value 40 to 30 dB
Frequency band 0.5 … 30 MHz
Limit value 30 dB
Class B
Tab.13: Emitted interference of the DC mains inputs and mains outputs
Immunity to inter-
ference
Parameter Values Standards
RF field, asymmetric, amplitude modulated
Frequency band 0.15 … 80 MHz DIN EN 61131-2
DIN EN 61000-6-2
DIN EN 61000-4-6
Test voltage 3 V
AM 80 % with 1 kHz
Source impedance 150 Ω
Criterion A
Bursts
Test voltage 2 kV DIN EN 61131-2
DIN EN 61000-6-2
DIN EN 61000-4-4
tr/tn 5/50 ns
Repetition frequency 5 kHz
Criterion A
Surge voltages, symmetric, line to cable
Series-mode interference tr/th 1.2/50 µs DIN EN 61131-2
DIN EN 61000-6-2
DIN EN 61000-4-5
0.5 kV
Surge voltages, asymmetric, line to earth
Common-mode interfer-
ence
tr/th 1.2/50 µs DIN EN 61131-2
DIN EN 61000-6-2
DIN EN 61000-4-5
1 kV
Tab.14: Interference immunity of the DC mains inputs and outputs

Jetter AG Mechanical installation | 5
JX3-BN-ETH User Manual 17 / 64
5 Mechanical installation
This chapter describes how to install and replace the JX3-BN-ETH.
5.1 Installing the device on the DIN rail
NOTICE Functional impairment caused by unfavorable installation
►Install the device only in vertical position on the DIN rail (DIN EN 60715).
►Keep the minimum distance to surrounding parts.
3
3
2
1
Fig.5: Installing the device on the DIN rail
1DIN rail 2Upper latch
3Minimum distance to surrounding parts = 30 mm
1. Disconnect the system from the power supply.
2. Place the upper latch (2) in angled position on the DIN rail (1).
3. Snap the lower latch of the device onto the lower edge of the DIN rail.
4. Slide the device to its intended position.

Jetter AG Mechanical installation | 5
JX3-BN-ETH User Manual 18 / 64
5.2 Removing the device from the DIN rail
The release latch lets you remove the device from the DIN rail.
2
A
A
1
Fig.6: Removing the device from the DIN rail
1DIN rail 2DIN rail release latch
ADetail view
1. Disconnect the system from the power supply.
2. Remove the device from the mains.
3. Pry the release latch (2) downwards and pull the device off the DIN rail (1).

Jetter AG Mechanical installation | 5
JX3-BN-ETH User Manual 19 / 64
5.3 Dismounting the enclosure from the backplane module
The upper and lower backplane tab on the module let you pull off the enclosure
from the backplane module.
NOTICE Mechanical damage and limited immunity to interferences
When replacing devices, degree of protection IP20 is not guaranteed. If you
touch the EMC clip, you may damage this clip. A damaged clip may result in
lower noise immunity.
►Do not touch any electronic components once the enclosure has been re-
moved from the backplane module.
The following information is retained on the backplane module:
■IP address
■Subnet mask
■Gateway
■DNS server
AA1
1
Fig.7: Dismounting the enclosure from the backplane module
1DIN rail latch ADetail view
1. Disconnect the system from the power supply.
2. Press the upper and lower latches (1) on the device simultaneously.
3. Keep the latches pressed and pull off the enclosure.

Jetter AG Electrical connection | 6
JX3-BN-ETH User Manual 20 / 64
6 Electrical connection
NOTICE Damages to material or functional impairment
Improper implementation of the wiring harness may cause mechanical stress.
►Protect the cables from bending, twisting or chafing.
►Install strain reliefs for the connecting cables.