John Lewis Daisy Daybed 803/41405 User manual

John Lewis
Daisy Daybed
Single Stock code: 803/41405
Thank you for purchasing this Daisy Daybed. Please read the instructions before use to ensure safe and
satisfactory operation of this product.
For product support or spare parts please
call the John Lewis Helpline;
T: 01244 689949
E: [email protected]
PRE-ASSEMBLY PREPARATION
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
Please check the pack contents before attempting to assemble this product. A full checklist of
components is given in this leaflet. If any components are missing, please contact the John Lewis
helpline.
This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL PARTS which should be KEPT AWAY FROM YOUNG CHILDREN .
Read this leaflet in full before commencing assembly.
If you require any additional information or have any issues with this product please call the John Lewis
Helpline on 01244 689949 or email:[email protected]
1/7

Fittings and parts checklist
Parts
Fittings
A
B
C
D
E
F
G
H
I
J
M6 x 25mm Bolt x 8 pcs
M6 x 38mm Bolt x 4 pcs
M6 x 12mm Bolt x 2 pcs
M6 x 63mm Bolt x 4 pcs
Screw Nut x 4 pcs
Cap Ends x 28 pcs
Allen Key x 1 pc
Spanner x 1 pc
Plastic Spacer x 4 pcs
Washer Spacer x 2 pcs
1
2
3
4
5
6
Arm Panel x 2
Back Panel x 1
Side Rails x 2
Tubing Slats x 2
Wooden Slats x 14
Cross Bar x 1
2/7

Step by step assembly instructions
Step One
Attach the Side Rails (3) to the Tubing Slats (4) by placing the Tubing Slats (4) into the 3 slots
(X, Y, Z) on the Side Rails (3) and securing with M6 x 38mm Bolts (B) and Screw Nut (E).
Tighten the Bolts (B) and Screw Nut (E) using the Allen Key (G) and Spanner (H) as shown in
the diagram below.
PLEASE NOTE: Only fully join areas highlighted
on the diagram (X, Y and Z) to allow the slats
to be inserted.
x 3
Step Two
Ensuring that the Wooden Slats (5) are facing curved side up, place a Cap End (F) onto each
end of the Wooden Slats (5) as shown in Fig.1. Now push each end into the slots along the
Side Rails (3) as detailed in Fig.2. Repeat for all slats.
3/7

Step Three
Place the Tubing Slat (4) into the last slot on the Side Rail (3) and secure using M6 x 38mm Bolt (B)
and Screw Nut (E) as shown below. Tighten the Bolt (B) and Screw Nut (E) using the Allen Key (G)
and Spanner (H) as detailed in the below diagram.
Step Four
Attach the top rails of the Arm Panels (1) to the Back Panel (2) using M6 x 63mm Bolt (D) and attach
the bottom rails of the Arm Panels (1) to the Back Panel (2) using M6 x 63mm Bolt (D) and
Washer Spacer (J) then tighten using the Allen Key (G) as shown in the diagram below.
4/7

Step Five
Attach the Side Rails (3) to the Arm Panels (1) using the Plastic Spacer (I) and M6 x 25mm Bolt (A)
as shown below.
Step Six
Attach the Cross Bar (6) to the Side Rails (3) using M6 x 12mm Bolt (C) then tighten with Allen Key (G)
as detailed below.
5/7

This bed is now ready to use.
6/7

Care and Maintenance
Metal
This bedstead should be cleaned using a soft damp cloth and dried immediately. Do not use a very
wet cloth or allow any liquid contact for a long period of time as this can permanently damage
the surface.
Do not use abrasive cleaner or harsh detergents as this can damage the surface.
Do not drag any object across the bed as this can cause permanent damage.
Safety Instructions
Never drag furniture when moving it. Always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or
injury. Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a
competent adult. No liability will be accepted for damage or injury caused by incorrectly installed or
assembled furniture. During assembly children should be kept away from the product due to
possible risk of injury.
Do not use this item if any components are missing or damaged.
This product complies with BS 1725:1998.
It is recommended that before moving heavy objects to a new location they are completely
dis-assembled to avoid personal injury or damage to the furniture. Please be careful to retain all
fittings when doing this.
If you require any additional information or have any issues with this product please call the
John Lewis Helpline on 01244 - 689949 or e-mail: [email protected]
John Lewis Partnership 171 Victoria Street London SW1E 5NN
www.johnlewis.com
7/7