John Lewis Ashton High Sleeper Bed User manual

John Lewis Stock Code 803/60512, 803/60813
Thank you for purchasing this Ashton High Sleeper. Please read the instructions carefully before use
to ensure safe and satisfactory operation of theis product.
Pre-assembly Preperation
Please ensure that instructions are read in full before attempting to assemble this product.
Please check the pack contents before attempting to assemble this product. A full
checklist of components are given in this leaflet. If any components are missing,
please contact the John Lewis helpline.
This product is HEAVY, it should be assembled as near as possible to the point of
use. TAKE CARE WHEN LIFTING to avoid personal injury and (or) damage to the
product.
This product takes approximately 150 MINUITES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM
YOUNG CHILDREN.
If you require any additional information or have any issues with this product please
call the John Lewis helpline on 01244 689949 or email [email protected]

Fittings Checklist
Allen Key M4
Barrel Nut
M6
Camfix
Minifix
Minifix
Bolt M6 x 100mm
Bolt M6 x 50mm
Bolt M6 x 35mm
Bolt M6 x 30mm
CSK Wooden Screw
M4 x 50mm
CSK Wooden Screw
M4 x 32mm
CSK Wooden Screw
M3.5 x 16mm
Handle Bolt
Pan Head Wooden
Screw
Handle
Hinges 7/8’’
Spring Washer
M6
Shelf Pin
Wood Dowel
M10 x 50mm
Wood Dowel
M8 x 30mm

Parts Checklist
Slats
Headboard Panel
Headboard Bottom Panel
Leg Pole (Left)
Leg Pole (Right)
Short Guard Rail
Long Guard Rail
Ladder Support
Ladder Vertical Rail
Ladder Horizontal Rail I
Ladder Horizontal Rail II
Side Rail Front
Side Rail Back
Bottom Side Rail

Step 1
Insert Dowel M10 x 50mm (S) and Barrel Nut M6 (B) into the Headboard Panel (1) and Headboard
Bottom Panel (2) as shown. Attach Headboard Panel (1) and Headboard Bottom Panel (2) to the Leg
Pole Left (3) and Leg Pole Right (4) using A Phillips Head Screwdriver and Allen Key M4 (A). Please
use a Phillips Head Screwdriver to align the Barrel Nut M6 (B) into the hole position to ensure Bolt
M6x 100mm (F) is fully secured. Then repeat to assemble the Headboard Panel (1) to both Leg
Poles (3) & (4) for other end.
Step 2
Insert Barrel Nut (B) into Side Rail Front (11), Side Rail Back (12) and Bottom Side Rail (13), using the
pre-drilled holes on both ends. Attach Side Rail Back (12) to the Headend and Footend. Then tighten it using
the Bolt M6 x 100mm (F) with Allen Key M4 (A). Repeat this for the Side Rail Front (11). Attach
Bottom Side Rail (13) to the headend and the footend and tighten it using Bolt M6 x 100mm (F) with Allen
Key M4 (A).
Please ensure that parts 11, 12 and 13 have been correctly positioned as shown in the above diagram. Part 11
must be correctly positioned to allow the ladders to be attached to the correct side of the high sleeper.
Please Note: Only 1 headboard bottom
panel (2) is required.

Step 3
Lay out the Horizontal Rail I (9), Ladder Horizontal Rail II (10) and Ladder Vertical Rail (8) as shown
below.
Step 4
Insert Barrel Nut M6 (B) into Ladder Horizontal Rail II (10) then push the Ladder Horizontal Rail II
(10) into the pre-drilled grooves in the Right Ladder Vertical Rail (8) and secure with Bolt M6
x 50mm (G) with Allen Key M4 (A) as shown in the diagram below. Insert Ladder Horizontal Rail I (9)
into the pre-drilled grooves. Repeat for Left Ladder Vertical Rail (8).

Step 5
Attach the ladder to Side Rail Front (11) using Bolt M6x 35mm (H) and tighten it using Allen
Key M4 (A) as shown below.
Please note: The grooved lines indicate the point which the mattress should not exceed, the
maximum height of the mattress to be used is 19cm.
Recommended size mattress is L:190cm, W: 90cm, H:19cm (max)
Step 6
PLEASE NOTE: The slats at each end have been cut to allow them to fit so that there are NO GAPS.
Starting at one end of the bed, secure the first fitted slat into place using Screw (K). Next secure the fitted
slat to the other end and secure using Screw (K) ensuring that there are NO GAPS between the slats and
the Headboards. Finally secure the rest of the Slats into place using Screw (K) as shown in the diagram
below using a Phillips Head Screwdriver.
WARNING
Maximum height of
the mattress. DO NOT
EXCEED THIS LINE.
Note: Ladder can be placed
either end of High Sleeper.

Step 7
Insert Dowel M8 x 30mm (T) into the bottom of Short Guard Rail (5) and Long Guard Rail (6). Attach
Long Guard Rail (6) to Side Guard Rail Back (12) and use bolt M6 x 100mm (F) to secure
to Leg Pole Left (3) and tighten bolts using Allen Key M4 (A). Then attach Short Guard Rail (5) to the
Side Rail Front (11) and use bolts M6 x 100mm (F) to fix it into Leg pole Right (4) and tighten
screws using Allen Key M4 (A).
Step 8
Attach Ladder Support (7) to Short Guard Rail (5) using bolt M4 x 35mm (H) and tighten it
using Allen Key M4 (A).
Please Note: Ensure all fittings are securely tightened before use.
Warning: Children can become trapped between the bed and the wall. To avoid risk of serious
injury the distance between the wall and the top safety barrier should be less than 75mm or more
than 230mm.

Parts Checklist for Book Rack
Horizontal Rail
Vertical Rail
Side Rail

Step 1
Insert Dowel M8 x 30mm (T) to Horizontal Rail
(1) and Vertical Rail (2) in pre-drilled holes.
Then insert Minifix (D) to Side Rail (3) as shown
below.
Step 2
Attach Vertical Rail (2) to Horizontal Rail (1) and
tighten using Camfix (C) with a Phillips Head
Screwdriver as shown in the diagram below.
Step 3
Attach Side Rail (3) to Horizontal Rail (1) and
Vertical Rail (2), tighten using Camfix (c) with
a Phillips Head Screwdriver as shown in the
diagram below.
Step 4
Attach Book Rack assembly inside the Ashton
High Sleeper Bed as shown in the diagram
below. Then using bolt M6 x 35mm
(H) and tighten using Allen Key M4 (A). Make
sure bolt M6 x 35mm (H) can be inserted
and tightened in the Book Rack, Bed Right and
Left Leg Poles.
Note: Please ensure the minix (D) used on the above step is
11mm not 9mm.
x 2
Please Note: Part 1 above is tted ush
to the top of part 2.

Parts Checklist for Desk
Back Panel
Shelf
Door Panel
Table top Side Rail
Bottom Panel
Back Bottom Panel
Table Top
Side Panel Left and Right
Table Top Support Rail
Support Rail
Front Bottom Rail