John Lewis House Equate Mirrored Cabinet 84982003 User manual

John Lewis
House Equate Mirrored Cabinet
Stock number: 84982003
Thank you for purchasing this House Equate Mirrored Cabinet. Please read the instructions
carefully before use to ensure safe and satisfactory operation of this product
Pre-assembly preparation
Necessary Tools
Please check the pack contents before attempting to assemble this product. A full checklist of
components is given in this leaflet. If any components are missing, please contact the retailer
from whom you bought this product.
TAKE CARE WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 60 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG
CHILDREN.
Please assemble on a soft clean surface to avoid damages to your product

Fittings checklist
A
Cam stud
x 12
G
Hinge
x 4
B
Cam
x 12
H
Screw for
adjustable wall
fixing
x 4
C
Wood Dowel
x 6
I
Adjustable Wall
fixing
X2
D
Shelf support
x 4
J
Cover caps
X12
E
Hinge screw
12 mm
x 24
F
Metal plate for
wall fixing
x 2

Parts checklist
1
Top panel
x 1
6
Back panel
x 1
2
Side panel Right
x 1
7
Door Left
x 1
3
Side panel Left
x 1
8
Door Right
x 1
4
Fixed shelf
x 1
9
Bottom panel
X1
5
Adjustable shelf
x 1
Wall fixing - if in doubt seek professional advice
Wood
If fixing to wood make
sure that it isn’t
chipboard as screws
can easily pull away
from the core structure
Brick or Masonry
Use an appropriate wall
plug provided you are
sure your wall is sound
Cavity wall
Special toggle wall
plugs are needed.
Seek expert advice

Step by step assembly instructions
Step One
Prepare the side panels for assembly by inserting 6 cam studs (A) into the allocated holes in
each side as shown. Gently tighten the cams clockwise with a crosshead screwdriver.
NOTE: Make sure the cam studs are fixed in a straight angle, and do not overturn.
Step Two
Insert one wood dowel (C) into each end of the top (1), the bottom (9) and the fixed shelf (4).

Step Three
Fix the top panel (1), the fixed shelf (4) and the bottom panel (9) to the side panel left as shown.
Insert cams (B) into the allocated holes and gently lock the cams clockwise. Do not overturn.
Step Four
Gently slide the back panel (6) into the groves in the top, bottom and side panels.
Please note the position of the cut outs in the back panel.

Step Five
Now connect the right hand side panel (2) to the top/bottom and shelf as shown.
Insert and gently lock cams (B) by turning clockwise. Do not overturn.
Step Six
Place the two adjustable wall fixings (I) in the top corners of the cabinet, and fix them with the
four fixing screws (H) supplied. The screws are tightened clockwise with a crosshead
screwdriver.

Step Seven
Gently lay each door (7+8) down on your protected working surface as shown, and fix two
hinges (G) on each door, using six hinge screws (E) on each hinge. The screws are tightened
clockwise with a crosshead screwdriver.
Step Eight
Fix the two metal plates (F) to a sound wall as shown below. The distance between the two
metal plates should be 444 mm measured from the outside of the plates.
Use a spirit level to ensure that both plates are in level. If in doubt, seek expert advice.
(Wall fixings not supplied.)

Step Nine
With two people gently place the cabinet on the two metal plates.
Place a spirit level on top of the unit and make final level adjustment on the adjustable wall
fixings from the inside of the unit.
Adjust the top screw with a Philips head screwdriver clockwise or anticlockwise until the unit is
in level, and finally adjust the bottom screws until the unit is flat against the wall.
Step Ten
Insert four shelf supports (D) in the required shelf position, tighten clockwise by hand, and
gently slide the adjustable shelf in place.
Finally add the cover caps (J) to the cams as shown.

Door adjustment
Please follow these simple steps for door adjustment:
In or out adjustment:
Loosen the rear hinge screw
anticlockwise, and gently move the hinge
in or out to the required position.
Re-tighten the adjustment screw by
turning clockwise.
Sidewise adjustment:
Turn the forward adjustment screw
clockwise or anticlockwise for sidewise
adjustment of the door.

Care and Maintenance
How to care for your furniture
Furniture with a melamine surface should be dusted with a dry cloth.
Spray polishes are best avoided as they contain silicones which may spoil the furniture’s
surface by building up over time.
Make sure all surfaces are protected from heat and liquids by mats and coasters. Wipe up spills
immediately and ensure that a mat or pad is placed under paper if you are writing.
Our furniture will endure most temperatures in the home but it is best to avoid placing furniture
next to heat sources such as radiators or fires.
Mirrors
Use glass cleaner or soapy water for cleaning, do not use anything abrasive as this may
damage the surface of the product.
Protect surfaces from scratches and marks by using mats and coasters.
Safety Instructions
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause
damage or injury.
Furniture can be dangerous if incorrectly installed. Wall fixing should be carried out by a
competent person. No liability will be accepted for damage or injury caused by incorrectly
installed or assembled furniture.
If the mirror is chipped or broken stop using the product and consult the manufacturer or
supplier.
This product is designed to be fixed securely to a sound wall in the manner stated.
It must under no circumstances be used free-standing. No liability will be accepted for damage
or injury caused by inadequate fixing or use without fixing.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
John Lewis Partnership 171 Victoria Street London SW1E 5NN
www.johnlewis.com