John Lewis Grace Bed User manual

Grace Bed
MTO
Thank you for purchasing this Grace Bed. Please read the instructions carefully before use to ensure safe
and satisfactory operation of this product.
Single
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact customer services on 01244 689949 or email
[email protected].
This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembl
Do not use power tools to assemble.
y.
PRE-ASSEMBLY PREPARATION
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
1/5

Wide Side Caps x 16
Fittings and parts checklist
AB
M5 Allen Key x 1 Side Plastic Caps x 16
1
2
3
4
5
6
Headboard x 1
Footboard x 1
Side Rails x 2
Slats x 16
Legs x 4
2/5
C
Wide Slats x 16

Head/Foot
Board
Preinserted Nut
Leg
Legs x 4
Step Two
Place Metal Brackets on Side Rails (3) over pre-inserted bolts in Headboard (1) and Footboard (2) and
tighten with the M5 Allen Key (A) to secure parts together.
Step by step assembly instructions
Step One
Place Legs (5) into the holes in the underside of the Headboard (1) and Footboard (2) as per diagram
below and twist into place so they are fully secured.
BRACKET
SIDE RAIL
3
1
1
3
3
2
1
2
3/5
6.
BRACKET
SIDE RAIL
2
3
1
2
6
6
6
6
6
M5
Bracket
Side Rail
3
1
2
AND
M5 Allen Key x 1
A.
S
T
E
P
1
S
T
E
P
2
S
T
E
P
3

2 Lines
Normal slats
2 Lines
Normal slat
2 Lines
Wide slats
2 Lines
Wide slats
2 Lines
Normal slats
2 Lines
Normal slats
4 Lines
Wide slats
ZONE 2
ZONE 1
ZONE 5
ZONE 7
ZONE 6
ZONE 4
ZONE 3
Diagram 1
With the curved side facing upwards, insert slats into a centre cap then into side caps on either end(x32).
(Please note the Wide Slats (5) must be inserted with the Wide Side Caps (C)). Repeat this process for all
slats.
Note: Please see the Diagram 1 below to arrange the slat with the correct system.
Step Three
4/5
Bed is ready to use.
Step Four
4.
5.
B
C.
Side Caps x 16
.
Wide Side Caps
x 16
Wide Slats x 16
Slats x 16
(x8)
x32
B
C
45
(x8)
C
C
B
4
5
B

IMPORTANT! PLEASE KEEP THESE
INSTRUCTIONS FOR FUTURE
REFERENCE
Care and Maintenance
Safety Instructions
5/5
Never drag furniture when moving it. Always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a competent adult.
No liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
During assembly, children should be kept away from the product due to possible risk of injury.
Do not use this item if any components are missing or damaged.
It is recommended that care is taken when moving heavy objects to a new location to avoid personal injury or
damage to the furniture. Please be careful to retain all fittings when doing this.
Children are likely to play, bounce, jump and climb on furniture, therefore the furniture should not be placed too
close to other furniture or windows, blind cords, curtain pulls or other strings or cords and should be placed either
tight to any wall or have a gap of 300mm between the wall and the side of the bed.
This product complies with BS EN 8509:2008+A1:2011.
This bed is for use with a standart single size mattress L190 x W90 x H18cm.
WARNING: Not suitable for children under 4 years old.
If you require any additional information or have any issues with this product please call the customer
services helpline on 01244 689949 or email [email protected].
Retain these instructions for future reference.
This bed should be cleaned using a soft, damp cloth and dried immediately.
Do not use a very wet cloth orallow any liquid contact for a long period of time as this can permanently
damage the surface.
Do not use detergents and do not rub as this can cause permanent damage.
Always protect your bed from direct sunlight as this may accelerate the natural on-going discolouration
process.
The legs of the bed should be tightened regularly.