John Lewis Portman Bedstead User manual

Portman Bedstead
Stock number: 810/84202, 810/84203
John Lewis
Double
Please ensure instructions are read in full before attempting to assemble this product
Necessary Tools
Please check the pack contents before attempting to assemble this product. A full checklist of
components is given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
This product is Heavy, it should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL PARTS which should be KEPT AWAY FROM YOUNG
CHILDREN.
Read this leaflet in full before commencing assembly.
If you require any additional information or have any issues with this product plase call the John Lewis
Helpline on 01244 689949 or e-mail [e-mail]
For product support or spare parts please call
the John Lewis Helpline;
T: 01244 689949
E: [email protected]
Thank you for purchasing this Portman Bedstead. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.
PRE-ASSEMBLY PREPARATION
1/5

2/5

5
C
E
C
E
C
E
C
E
5
C
E
1
2
3
B
A
J
3/5
Step by step assembly instructions
Step One
Attach the Side Rails (3) to the Head Board (1) and Foot Board (2) using Washer (A) and Bolt M6 x 25mm
(B). Tighten using Allen Key (J) as shown in the diagram below.
Step Two
Place the Tubing Slats (5) onto the Side Rails (3) and secure using bolt M6 x 30mm (C) M6 (E)
As shown in the diagram below.
3
3
J
J

H
D
E
G
7
6
4
Note: Once the supporting legs are secured in place, unscrew the adjuster (F) slightly, ensuring there is a small
gap of 5mm in between the adjuster (F) and the hard point of the floor.
6F
Step Four
I
3
3
G
4/5
This bed is now ready to use.
Ensuring the holes along the centre rail (7) are facing upwards, attach to the underside of Tubing Slats (5) using
M6 x 35mm Bolt (D) and M6 Nut (E). Screw the adjuster (F) fully into the bottom of the supporting legs (6).
Attach the supporting legs (6) into the pre - drilled holes on the under side of the centre rail (7) using
M6 x 35mm Bolt (D) and M6 lock nut (I).
Step Three
Starting at the headboard (I), attach the centre plastic holders (G) into the holes along the centre rail (7) Ensuring the
wooden slats (4) has the curved side facing up, place the side cap (H) onto one end of the wooden slats (4). Insert the
other end of the wooden slat (4) into the centre plastic holder (G), then insert the side cap (H) onto the side rail (3) into
the pre-drilled holes. Repeat this process for all the wooden slats on both sides of te centre rail.
J
J

Care and Maintenance
Metal
Do not use abrasive cleaner or harsh detergents as this can damage the surface.
Do not drag any object across the bed as this can cause permanent damage.
Safety Instructions
Never drag furniture when moving it, always lift it.
Do not use this item if any components are missing or damaged.
It is recommended that before moving heavy objects to a new location they are completely dis-assembled
If you require any additional information or have any issues with this product please call the John Lewis
Helpline on 01244 689949 or e-mail [email protected].
John Lewis Partnership 171 Victoria Street London SW1E 5NN
www.johnlewis.com
5/5
This bedstead should be cleaned using a soft damp cloth and dried immediately. Do not use a very wet
cloth or allow any liquid contact for a long period of time as this can permanently damage the surface.
Please take care when handling or moving the furniture as careless handling may cause damage or
injury. Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a competent
adult. No liability will be accepted for damage or injury caused by incorrectly installed or assembled
furniture. During assembly children should be kept away from the product due to possible risk of injury.
This product complies with BS 1725: 1998