John Lewis Devon Wardrobe User manual

John Lewis Stock Code 803/61807,
803/61607, 803/61707
Thankyou for purchasing this Devon Wardrobe. Please read the instructions carefully
before use to ensure safe and satisfatory operation of the product.
For product support or spare
parts please call the John Lewis
helpline;
T: 01244 489949
E: [email protected]
Pre-assembly Preperation
Please ensure that instructions are read in full before attempting to assemble this product.
Please check the pack contents before attempting to assemble this product. A full checklist of
components are given in this leaflet. If any components are missing, please contact the John
Lewis helpline.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE
CARE WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 90 MINUITES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG
CHILDREN.
If you require any additional information or have any issues with this product please call the
John Lewis helpline on 01244 689949 or email [email protected]
Necessary Tools
Page 1 of 16

1pc- Door Knob 26pcs- Cam 6 x 24mm
28pcs- Dowel 8 x 30mm 1pc - Screw 4 x 40mm
20pcs- Screw 4 x 15mm
3pcs- Cup Hinge
4pcs- Washer
1pc- Hanging Rail 25 x 583mm
1pc- Nail Guide
2cps- Strap
1pc- Joining Strip - 1655mm
3pcs- cross plate
26pcs-Camlock 15 x 10.5mm
36pcs- Nail
2pc- Magnet
4pcs- Screw 4 x 25mm
2 pcs- Hanging
Rail Cup
Page 2 of 16

Top
1pc
Plinth
1pc
Shelf
2pcs
Plinth
3pcs
Bottom
1pc
Door
1pc
Side left
1pc
Back 2pcs
Page 3 of 16

P
s
Page 4 of 16
Function of Cam and Camlock
Step 1
Fix the Cam to the
wooden panel
Step 2
Push the wooden
panel with the attached
Cam onto the other
panel
Step 3
Place the Camlock
into the hole, arrow
pointing towards the
bolt.
Step 4
Tighten: turn the
Camlock to the right.

Step 1
Knock the Dowels (D) in to the pre-drilled holes indicated on the shelf (4), Bottom (9), Plinths (2) and (3)
and on the Sides (6) and (7).
Page 5 of 16

Step 2
Attach the Hanging Rail Cup( Q) on to the Side panels (6) & (7) using Screw (G) into the pre-drilled
holes. See fig 6.1. Attach the Cross Plate (T) to the Right Side (7) using the premounted screw and 2 x
Screw (G). The long end of the cross plates must point towards the front edge of the side as shown in
fig 6.2
Step 3
Attach the Magnet (l) to the Left Side (6) using Screw 4 x 15mm (G). The magnet shold be placed excatly
as shown in the diagram below.
Page 6 of 16

Step 4
Screw Cam 6 x 24mm (B) into the holes indicated on the Top (1) and both Sides (6) & (7) as shown in
the diagram below.
Step 5
Push the Plinths (2) & (3) into the pre-drilled holes on the Left Side (6), as shown in the diagram below.
Using instructions on “function of Cam and Camlock” on page 4, place the Cam (C) into the pre-drilled
holes indicated on the diagram below and tighten by turning the Camlock (C) to the right.
Page 7 of 16

Step 6
Affix the shelf (4) and Bottom (9) onto the the Left Side (6). Using the instructions on “function of cam
and camlock” on page 4, place the Camlock (C) into the pre-drilled holes indicated on the diagram below
making sure that the arrows point towards the side/bolt., and tighten by turning the Camlock (C) to the
right.
Step 7
Affix the Right Side (7) onto the Bottom (9). Shelf (4) and Plinths (2) & (3). Using the instructions on
“function of cam and camlock” on page 4, place the Camlock (C) into the pre-drilled holes indicated
on the diagram below making sure that the arrows point towards the side/bolt., and tighten by turning
the Camlock (C) to the right.

Affix the Top (1) onto the Sides (6) & (7) Using the instructions on “function of Cam and Camlock” on
page 4, place the Camlock (C) into the pre-drilled holes indicated on the diagram below making sure
that the arrows point towards the side/bolt., and tighten by turning the Camlock (C) to the right.
Step 8
Page 9 of 16

Step 9
Place the Back (8) into the rebate of the Top (1) and Left Side (7), ensuring that there is NO GAP
between the side and the back, or between the top and the back. Fasten the back with Nail (F) along
the top using the nail guide (H), see fig10.1, remembering the angle between the top and the bottom
must be 90 degrees see fig10.2. Fasten the back along the side and bottom.
Page 10 of 16