John Lewis Emily Storage Bed User manual

Double
For product support or spare parts please call
the John Lewis Helpline;
T: 01244 689949
E: [email protected]
Emily Storage Bed
PRE-ASSEMBLY PREPARATION
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 90 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembl
Do not use power tools to assemble.
y.
If you require any additional information or have any issues with this product please call the
John Lewis Helpline on 01244 689949 or email [email protected]
John Lewis
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
1/9
Thank you for purchasing this Emily storage bed. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.

2/9
Wide Centre Caps x 8
Wide Side Caps x 16
Fittings and parts checklist
A
B
C
F
G
D
E
J
K
L
M
H
I
M4 Allen Key x 1 pcs
M5 Allen Key x 1 pcs
Side Plastic Caps x 14 pcs
M8 Spring Washer x 8 pcs
Centre Plastic Caps x 7 pcs
M8 X 16mm Bolt x 8 pcs
M6 X 25mm Bolt x 2 pcs
M6 X 40mm Bolt x 8 pcs
Screw 3.5 x 30mm x 40pcs
Screw 4 x 50mmx 4pcs
Screw 4 x 18mm x 8pcs
Fittings

3/9
Headboard x 1 Footboard x 1 Side Rails x 2
Slats x 14 Wide Slats x 16
Drawer Runner Base x 2 Drawer Centre Support x 1
Drawer Sides x 4 Drawer Fronts x 2 Drawer Backs x 2
Drawer Bottoms x 2
Centre Rail x 1
Legs x 4
Upholstered Front Panels x 2 Drawer Bottom Supports x 6
12 3
456
7 8 9
10 11 12
13 14 15
Metal Stopper x 4
Parts
16

4/9
Head/Foot
Board
Preinserted Nut
Wooden Leg (7)
Legs x 4
Step Two
Step by step assembly instructions
Step One
Place Wooden Legs (7) into the holes in the underside of the Headboard (1) and Footboard (2) as per
diagram below and twist into place so they are fully secured.
1
2
3
1
2
BRACKET
SIDE RAIL
3
1
BRACKET
SIDE RAIL
2
3
Hook the pre-attached brackets on the Side Rails (3) over the pre-inserted bolts in the head and footboard and
hand-tighten bolts to loosely secure parts together. Do not tighten with the M5 Allen Key (B) until you have
inserted the Centre Rail in Step Five.
LOOSELY SECURE PARTS
TOGETHER IN ORDER FOR
CENTRE RAIL TO FIT IN
STEP FIVE
3
7.

5/9
Step Three
Step Four
Attach M8 Spring Washer (G) and M8 x 16mm Bolt (H) into the metal fixings on to both Drawer Runner Base (8)
(only for the top side). Insert the Drawer Runner Base (8) inside the bed frame as shown in Step 2. Next, attach the
M8 Spring Washer (G) and M8 x 16mm bolt (H) into the bottom side of metal fixing on the Drawer Runner Base (8).
Loosely tighten the bolts using M5 Allen key (B).
M8 x 16mm
Bolt
x 8
M8 Spring Washer
x 8
B.
M8 x 16mm
Bolt (H)
M8 Spring Washer (G)
8
STEP 1
8
3
1
3
8
3
2
M5 Allen Key x 1
G. H.
LOOSELY SECURE PARTS
TOGETHER IN ORDER FOR
CENTRE RAIL TO FIT IN
STEP FIVE
8
8
Fig 2
M5 Allen Key
(B)
STEP 2
Screw
4 x 50mm x 4
1
3
3
2
8
9
8
8
9
8
x1
3
Attach Drawer Centre Support (9) to Drawer Runner Base (8) and secure into place using Screws 4 x 50mm (K)
as shown in the diagram below.
K.
Cross head
Screw Driver
Screw
4 x 50mm (I)
Screw 4 x 50mm (K)
8

6/9
1
6
3
3
2
Step Five
Step Six
1
M4 Allen Key (A)
M6 x 25mm (I)
M4 Allen Key x 1 M6 x 25mm Bolt x 2
A. I.
AFTER INSERTING CENTRE
RAIL, TIGHTEN ALL FIXINGS
FULLY INCLUDING BOLTS
AT SIDE RAILS (FROM
STEP TWO)
Insert Centre Rail (6) into the brackets on the Headboard (1) and Footboard (2). Push down fully and
secure in place using M6 x 25mm Bolts (I). Tighten using M4 Allen Key (A). You can now tighten the bolts
with M5 Allen Key (B) at the Side Rails from Step Two so all fastenings are now tightened.
S
T
E
P
1
S
T
E
P
2
(x2) (x2)
11
11
12
13
14
10
(x2)
3.5 x 30mm(40)
Cross Head
Screw Driver
L.
10
10
15
15
15
Fig. 1 Fig. 2 Fig. 3
To construct the drawers, fix Drawer Front (11) with one end of each Drawer Bottom Support (15) using
Screws 3.5 x 30mm (L) as shown in Fig.1, then fix the Drawer Sides (10) to the Drawer Back (12).
Next, insert Drawer Bottom (13) and then fix Drawer Front (11) using Screws 3.5 x 30mm (L) as shown in
Fig.2. Finally, secure the other end of the Drawer Bottom Supports (15) to the other side of the drawer and
tighten using a cross head screw driver.
10

7/9
Step Seven
Step Eight
M6 x 40mm x 8
M4 Allen Key x 1
Attach Upholstered Front Panel (14) to drawer and tighten together using M6 x 40mm Bolt (J).Tighten with
M4 Allen Key (A).
A. J.
x2
14 14
8
16
10
16.M.
4x
Metal Stopper x 4
Slide drawers into both sides of the bed frame. Attach Metal Stopper (16) to the Drawer Runner base (8)
using screw 4 x 18mm (M).
Screw 4 x 18
x 8

8/9
2 Lines
Normal slats
1 Line
Normal slat
2 Lines
Wide slats
2 Lines
Wide slats
2 Lines
Normal slats
2 Lines
Normal slats
4 Lines
Wide slats
ZONE 2
ZONE 1
ZONE 5
ZONE 7
ZONE 6
ZONE 4
ZONE 3
Diagram 1
D
F
4
5
(x8)
(x7)
4.
5.
C.
D
F.
E.
Side Caps x 14
.
Wide Centre Caps
x 8
Wide Side Caps
x 16
Wide Slats x 16
Slats x 14
With the curved side facing upwards, insert 2 slats into a centre cap then into 2 side caps on either
end(x15). (Please note the Wide Slats must be inserted with the Wide Centre Caps (E) and Wide
Side Caps (F)). Repeat this process for all slats.
Note: Please see the Diagram 1 below to arrange the slat with the correct system).
4
4
C
E
5
5
Centre Caps x 7
E
F
F
D
D
4
4
5
5
C
Step Ten
Step Nine
The bed is now ready for use.

9/9
Care and Maintenance
Safety Instructions
If you require any additional information or have any issues with this product please call
the John Lewis Helpline on 01244 689949 or email [email protected]
John Lewis Partnership 171 Victoria Street, London, SW1E 5NN.
www.johnlewis.com
Never drag furniture when moving it. Always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Any assembly should be carried out by a competent
adult.
No liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
During assembly, children should be kept away from the product due to possible risk of injury.
Do not use this item if any components are missing or damaged.
It is recommended that care is taken when moving heavy objects to a new location to avoid
personal injury or damage to the furniture. Please be careful to retain all fittings when doing this.
This Emily Storage Bed should be cleaned using a soft damp cloth and dried immediately.
Do not use a very wet cloth or allow any liquid contact for a long period of time as this can permanently
damage the surface.
Do not use detergents and do not rub as this can cause permanent damage.
Always protect your bed from direct sunlight as this may accelerate the natural ongoing discolouration
process.
Bolts holding together the bed frame should be tightened regularly.
Please retain this information leaflet for future reference.
This product complies with BS EN 1725:1998.