John Lewis Rouen Bed User manual

Rouen Bed
PRE-ASSEMBLY PREPARATION
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
If you require any additional information or have any issues with this product please call the
John Lewis Helpline on 01244 689949 or email [email protected]
Stock Code: 803/44302
Stock Code: 803/44303
Double
King
John Lewis
For product support or spare parts please call
the John Lewis Helpline;
T: 01244 689949
E: [email protected]
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
Thank you for purchasing this Rouen Bed. Please read the instructions carefully before use to ensure safe
and satisfactory operation of this product.
1/6
(NOT INCLUDED)

Fittings and parts checklist
A
B
C
D
E
F
G
H
I
M5 Allen Key x 1
M4 Allen Key x 1
Side Caps x 30
Centre Caps x 15
M6 X 25mm Bolt x 6
M8 Spring Washer x 2
1
2
3
4
5
6
Headboard x 1
Footboard x 1
Side Rails x 2
Slats x 30
Centre Rail x 1
Legs x 4
Parts
Fittings
2/6
Spanner M13 x 1
7
Metal Plates x 2
Nut M8 x 2
Screw 3.5 X 30mm x 2

1
3
3
2
5
Place Metal Bracket on Side Rails (3) over pre-inserted bolts in Headboard (1) and Footboard (2) and hand-tighten
to loosely secure parts together. Do not tighten bolts with M5 Allen Key (B) until you have inserted the Centre Rail
in the next step.
Step One
Step Two
Step by step assembly instructions
3/6
Lower the Centre Rail (5) into the brackets in the centre of the Headboard (1) and Footboard (2) as shown in
fig.3. Now secure the Centre Rail (5) using M6 x 25mm Bolts (E) and tighten with M4 Allen Key (A) as shown
in fig.4. You can now tighten the bolts at the Side Rails from previous step (Step One) with the M5 Allen
Key (B) so all fastenings are now tightened.
M4
M6 x 25mm (2)
E. A.
Centre Rail
F
i
g
.
3
51
2
And
M4(A)
M6 x 25(E)
F
i
g
.
4
5
1
2
And
M5
M5
Bracket
Side Rail
3
1
2
AND
1
3
3
2
Bracket
Side Rail
1
2
3
AND
B.
Fig.1
Fig.2
LOOSELY SECURE PARTS
TOGETHER IN ORDER FOR
CENTRE RAIL TO FIT IN
NEXT STEP
AFTER INSERTING CENTRE RAIL,
TIGHTEN ALL FIXINGS FULLY
INCLUDING BOLTS AT SIDE RAILS
(FROM STEP ONE)

Step Three
Step Four
Starting with the Headboard (1), insert the Front Legs (6)x2 into the pre-drilled holes on the underside of the
Headboard (1) and twist to secure, as shown
in the diagram below.
Legs x 2
E.
6.
Nut M8 (2)
Spanner M13 (1)
Screw
3.5 x 30mm (2) M6 x 25mm Bolt (4)
6
Legs (2)
7.6.
Metal plates (2)
Spring
Washer M8 (2)
A.
M4 Allen Key (1)
x2
F
o
r
H
e
a
d
b
o
a
r
d
O
n
l
y
4/6
3
1
H.G.I.F.
For Footboard Only
3
M6 x 25mm (E)
2
7
M4 (A)
M6 x 25mm (E)
3
M6 x 25mm (E)
2
M4 (A)
M6 x 25mm (E)
7
3.5 x 30mm (H)
3.5 x 30mm (H)
Spanner M13 (I)
Nut M8 (G)
Spring
Washer M8 (F)
7
6
2
3
STEP 1
STEP 2
Attach the Metal Plate (7) to the bottom of Footboard (2) using bolt M6 x 25mm (E)x2 and Screw 3.5 x 30mm (H)x1.
Tighten the bolt with M4 Allen Key (A). Repeat process for other Footboard Leg. Next, insert Wooden Leg (6) into the
bottom of Metal Plate (7) using Spring Washer (F)x1, M8 Nut (G)x1 then tighten with Spanner M13 (I).
Yellow Sticker
face down

C
D
4
Starting at the headend, insert the Centre Caps (C) along the Centre Rail (5). Ensuring that the Slats (4) are
facing curved side up, insert into the Centre Caps (C). Place a Side Cap (D) onto the other end of the
Slats (4) and push down fully into the pre-drilled holes along the Side Rails (3), as shown in the diagram below.
Repeat this process to attach all 30 Slats (4).
Step Six
Side Caps (30 pcs)
Centre Caps (15 pcs)
Slats (30pcs)
4.
C.
D.
5/6
Step Five
This bed is now ready to use.

Care and Maintenance
Safety Instructions
This Rouen bed should be cleaned using a soft, damp cloth and dried immediately. Do not
use a very wet cloth or allow any liquid contact for a long period of time as this can permanently
damage the surface.
Do not use detergents and do not rub as this can cause permanent damage.
Always protect your bed from direct sunlight as this may accelerate the natural ongoing discolouration
process.
Screws holding together the bed frame should be tightened regularly.
Please retain this information leaflet for future reference.
This product complies with BS EN 1725:1998.
If you require any additional information or have any issues with this product please call
the John Lewis Helpline on 01244 689949 or email [email protected]
John Lewis Partnership 171 Victoria Street, London, SW1E 5NN.
www.johnlewis.com
Never drag furniture when moving it. Always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Any assembly should be carried out by a competent adult.
No liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
During assembly, children should be kept away from the product due to possible risk of injury.
Do not use this item if any components are missing or damaged.
It is recommended that care is taken when moving heavy objects to a new location to avoid
personal injury or damage to the furniture. Please be careful to retain all fittings when doing this.
6/6