John Lewis Rose Mirror Robe 803/16611 User manual

1
Rose Mirror Robe
Stock number: 803/16611
Thank you for purchasing this Rose Mirror Robe. Please read the instructions carefully before use to ensure safe
and satisfactory operation of this product.
Pre-assembly preparation
Please ensure instructions are read in full before attempting to assemble this product
Necessary Tools
Please check the pack contents before attempting to assemble this product. A full checklist of components
is given in this leaflet. If any components are missing, please contact John Lewis Customer Services or
your local branch.

2
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury or damage to the product.
This product takes approximately 60 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG
CHILDREN.
Read this leaflet in full before commencing assembly.
Fittings and parts checklist
G
I
A
E
C
J
B

3
A 1 x Top F 20 x 25mm
Screws
B 1 x RHF
S. Panel
G 1 x Dorr frame &
Doors
C 1 x LHF
S. Panel
H 12 X 30mm
Screws
D 7 x 50mm
Screws I 1 x
Hanging
Rail
E 1 x Base
Unit
J 1 x Back
Panel

4
Step by step assembly instructions
Step One
Fittings
___________________________________________________________________________
Step Two
Fittings
With the aid of an assistant steadying the panels from the back, locate the Left side panel (C) and
Right side panel (B) onto the Base unit (E) and ensure the dowels are squarely located and the
panels are kept vertical. The support for the hanging rail being at the top and the post at the rear.
Screw in 2 x 30mm screws (H) into the holes provided.
One or more persons lift up the front section (G) with the hinges on the inside and the front
inside rail with the 4 screw holes is at the bottom and place onto the top of the base unit. Push the
front up against the sides (B) & (C) so there is no gap between the vertical ends of the front panel
and the side panels. After the front has been located the person standing at the front should hold
the sides and front together by holding the palms of their hands on the sides of the front section
(G) and fingers on the sides (B) & (C) whilst the person at the back screws the front onto the
sides by first screwing in the top 2 screws (H) then the bottom 2 (H). Once these 4 screws are
fixed, the person at the front ca
n let
go and the remaining 4 screws (H
) can be tightened up
H x 8
G
B
C
H
H
H
H
H
H
H
H
H
H
H x 2

5
___________________________________________________________________________
Step Three
Fittings
__
_______________________________________________________________________
Step Four
Fittings
Secure the bottom of the door frame using 4 x 50mm screws (D).. Fit the Hanging rail (I) into its
cradle
Locate the Top (A) as shown onto the 4 dowells and secure to the Side panels using 4 x 50mm
Screws (D) ensuring the cornice runs around the front and 2 sides. Screw in to the front section 2
x 30mm screws (H) and tighten.
G
G
G
G
D x 3
D x
4
I
D
D
D
D
D
D
D
A
H
H
H
x
2

6
_________________________________________________________________________
Step Five
Fittings
Care and Maintenance
The John Lewis Rose bedroom collection is crafted from solid Birch and Birch veneers and then hand
finished with several coats of paint. Each piece is then individually distressed. This is achieved by gently
rubbing by hand the top layers of finish to get to the initial coats of paint to create an authentic aged
appearance. Some distressing will be black and some will be clear, but this is a natural characteristic of
the effect.
Every item is unique in the way it is finished and the cracks and rubs in the paint finish are an integral
part of the design.
All carving on the Rose range is done by hand by skilled craftsmen that are specifically trained. The
signature carved Roses take 4 hours apiece to produce
Move the wardrobe close to the position where you intend to use it, by lifting the product and not
dragging the wardrobe.. Sometimes floors are uneven and you may need to lean the wardrobe
slightly left or right to make the doors sit square inside the frame (correct position). Once the
doors are square (correct position) fit the Back panel (J) using 16 x 30 mm Screws (F) ensuring
the rails run horizontally facing the outside of the cabinet. First fit the bottom 2 outer screws,
then the top 2 outer and finally the remaining screws
F x 20
F
F
F
F

7
Safety Instructions
General warnings:
Never drag furniture when moving it, always lift it. Periodically check all fixings to ensure none have
come loose and re-tighten where necessary. Please take care when handling or moving the furniture as
careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a competent
person. No liability will be accepted for damage or injury caused by incorrectly installed or assembled
furniture.
Wall Fixing Strap :
Your Rose product is supplied with a wall fixing strap which John Lewis would always recommend is
used to secure the product against the wall. Attach one end of the wall fixing strap to the top of the unit
with the screw provided and the other end should be attached to the wall by a competent person.
Specific warnings for heavy items:
It is recommended that before moving heavy objects to a new location they are completely disassembled
to avoid personal injury or damage to the furniture. Please be careful to retain all fittings when doing this.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
John Lewis Partnership 171 Victoria Street London SW1E 5NN
www.johnlewis.com