John Lewis Darton Groove 810/80701 User manual

Darton Groove 90cm Soft White/Oak Bed
PRE-ASSEMBLY PREPARATION
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 45 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
If you require any additional information or have any issues with this product please call the
John Lewis Helpline on 01244 689949 or email [email protected]
Stock Code: 810/80701
Single
John Lewis
For product support or spare parts please call
the John Lewis Helpline;
T: 01244 689949
E: [email protected]
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
Thank you for purchasing this Darton Groove Bed. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.
1

Fittings and parts checklist
A
B
C
D
E
Bolt x 8
Allen Key - 4mm x 1 Cam x 2
Screw x 24
Bolt x 2
1
2
3
4
5
Headboard x 1
Footboard x 1
Top Rail x 1
Side Rails x 2
Slat Set x 1
2
(M8 x 22 mm)
(30 mm)
( 12 x 10.5 mm)
(M6 x 24 mm)
Dowel x 3
( 10 x 30 mm)
Fittings
Parts
F

Step by step assembly instructions
Step One
Screw the Bolts (E) into the holes indicated on the Top Rail (3).
E x 2 pcs
E
3
Step Two
Place the Dowels (F) into the holes in the Headboard (1) and press down the Top Rail (3) onto the
Headboard (1). Fix the Top Rail (3) to the Headboard (1) using Cams (D) as shown below.
1. Lower the bolt
into the hole.
2. Place the cam into
the hole indicated,
arrow pointing
towards the bolt.
3. Tighten by turning
the cam to the right.
1
2
3
x 2 pcs
D
x 3 pcs
3

Step Three
Fix the Side Rails (4) to the Headboard (1) and Footboard (2) using Bolts (B) as shown below.
Tighten using Allen Key (A).
4
1
4
4
2
B
B
B
B x 8 pcs
4
12

Step Four
This bed is now ready to use.
5
Place one of the Slats (5) at the top of the Headboard then slide the rest down the bed until the last one
reaches the Footboard, ensuring the end Slats are as close to the Headboard and Footboard as possible.
Fix all Slats (5) in place using Screws (C).
C
C x 24 pcs
5
C
C
C

6
Care and Maintenance
Wood furniture
Wood displays different grain patterns depending on which way they cut - for example, the ‘medullary
ray’ which can appear on oak furniture is a mark of good quality timber - these are just characteristics
of the natural beauty of the wood. Some furniture is also deliberately aged and rustic.
Wood veneer also allows distinctive patterns to be created on flat surfaces, such as table tops and
drawer fronts by the way the slivers are arranged.
All timber surfaces will change colour and mellow over time. New furniture will initially vary in shade from
items that have been previously purchased.
How to care for your wood furniture
Furniture with a hard lacquer, wax polish or painted surface should be dusted with a dry cloth.
Waxed furniture will need to be given a coat of beeswax a couple of times a year to help maintain its lustre.
Spray polishes are best avoided as they contain silicones which may spoil the furniture’s surface by
building up over time.
Our furniture will endure most temperatures in the home but it is best to avoid placing furniture next to
heat sources such as radiators or fires. Be particularly careful with solid wood as the lack of humidity
caused by central heating can cause damage such as warping.

7
Safety Instructions
Never drag furniture when moving it. Always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten when necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or
injury.
Furniture can be dangerous if incorrectly installed. Any assembly should be carried out by a
competent adult.
No liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
During assembly, children should be kept away from the product due to possible risk of injury.
Do not use this item if any components are missing or damaged.
It is recommended that care is taken when moving heavy objects to a new location to avoid
personal injury or damage to the furniture. Please be careful to retain all fittings when doing this.
Children are likely to play, bounce, jump and climb on furniture, therefore the furniture should not be
placed too close to other furniture or windows, blind cords, curtain pulls or other strings or cords and
should be placed either tight to any wall or have a gap of 300mm between the wall and the side of
the bed.
This product complies with BS 8509:2008+A1:2011.
If you need any additional information or have any issues with this product please call the
John Lewis helpline on 01244 689949 or email [email protected]
John Lewis Partnership 171 Victoria Street London SW1E 5NN
www.johnlewis.com
This bed is for use with a standard single size mattress L190 x W90 x H18.
Warning: Not suitable for children under 4 years old.
Warning: Do not place this child’s bed near heat sources, windows or other furniture.
Warning: Do not use this child’s bed if any part is broken, torn or missing.