John Lewis Napoli 80310606 User manual

Please check the pack contents before attempting to assemble this product. A full checklist of compo-
nents is given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
his product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
his product takes approximately 60 MINUTES to assemble with 2 PEOPLE.
he fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
If you are missing some fittings please contact our spare parts helpline on 0330 005 9435.
Opening hours are 9am - 5pm Monday to Friday.
John Lewis
Stock Code: 80310606
Napoli dressing ta le
hank you for purchasing this Napoli dressing table. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.
PRE-ASSEMBLY PREPARATION
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
Screwdriver
002030405060708090 00 020 30 40 50
023456
Ruler/tape
measure Small hammer
Drill Eye protection
Spirit level
NAN 04/14
Page 1
REMOVE PROTECTIVE
FILM FROM SIDE PANELS
AND TOP/BOTTOM PANEL
BEFORE FIXING THEM TO
OTHER COMPONENTS

Metal dowel x 27 Long cam lock x 23 Short cam lock x 4
Wooden dowel x 16
30mm
12mm
10.5mm
30mm
68
40mm
8
Wooden dowel x 8
30mm Screw x 4
30mm Screw x 8 Allen key x 1 Bumper x 1
11mm Euroscrew x 8 16mm Screw x 8
Wooden dowel x 4
Runners x 2
A B C
G
L
H
M
Q R S
D E F
I
N
P
Arm x 2
O2
O1
Conformat x 4
Plastic hinge x 2
Support foot x 4
Page 2
NAN 04/14
Fittings checklist

1
2
3
4
5
6
7
8
13
16
17
18
18
14
15
9
11 10
12
11 10
12
9
Page 3
NAN 04/14
Parts checklist

B
B
E
E
3
B
B
E
E
4
O1
H
2
B
O1
1
M
A
B
O2
2
M
A
B
Page 4
Step by step assembly instructi ns
Step One
Place the cam lock (B) nto the holes on panels (3) (4), arrow po nt ng towards the bolt.
Attach 8x wooden dowels (E)
nto the pre-dr lled holes
as shown.
1.
2.
NAN 04/14
Step Two
Attach 8x metal dowels (A) nto the pre-dr lled holes on s de panels (1) (2) as shown.
Use a screwdr ver to turn f tt ng (A) clockw se to f x.
F x runner parts (O1) (O2) to the s de panels (1) (2) through holes shown
n the deta l v ew us ng 4x euroscrews (H).
Place the cam lock (B) nto the holes on panels (1) (2),
arrow po nt ng towards the bolt.
F x 4x support foot (M) as shown
1.
2.
3.
4.

Page 5
NAN 04/14
Step by step assembly instructi ns
Step Three
Attach panels (3) (4) onto s de panels (1) as shown. Ensure metal dowels (A) and wooden dowels (E)
are al gned correctly w th the holes of match ng parts before attach ng.
Secure panels us ng a screwdr ver to turn f tt ng (B) clockw se to f x.
1.
2.
3
4
1
1
2
B
A
3
4
2
12
B
A
Step Four
Attach s de panels (2) onto panels (3) (4) as shown. Ensure metal dowels (A) and wooden dowels (E)
are al gned correctly w th the holes of match ng parts before attach ng.
Secure panels us ng a screwdr ver to turn f tt ng (B) clockw se to f x.
1.
2.

E
D
D
E
D
D
17
16
14
15
B
B
B
Page 6
Step by step assembly instructi ns
Step Five
Attach 4x wooden dowels (E) nto the pre-dr lled holes of panels (14)(15) as shown.
Attach 8x wooden dowels (D) nto the pre-dr lled holes of panels (16)(17) as shown.
Place the cam lock (B) nto the holes on panels (14) (15)
arrow po nt ng towards the bolt.
1.
2.
3.
NAN 04/14
G
G
14
4
R
Step Six
F x panel (14) onto bottom panel (4) us ng 2x conformat screws (G) and allen key (R).1.

16
3
Page 7
NAN 04/14
Step by step assembly instructi ns
Step Seven
Attach panel (16) onto panel (3) Ensure wooden dowels (D) are al gned correctly w th the holes of match-
ng parts before attach ng.
1.
17 15
16
Step Eight
Attach panel (17) onto panel (16) as shown. Ensure wooden dowels (D are al gned correctly w th the
holes of match ng parts before attach ng.
Attach panel (15) onto panel (17) as shown. Ensure wooden dowels (D) are al gned correctly w th the
holes of match ng parts before attach ng.
1.
2.

Step by step assembly instructi ns
Step Nine
F x panel (15) onto bottom panel (4) us ng 2x conformat screws (G) and allen key (R).1.
G
G
4
15
R
13
A
2
B
1
B
A
14
13
15
16
Page 8
NAN 04/14
Step Ten
Attach 5x metal dowels (A) nto the
pre-dr lled holes on panel(13).
Use a screwdr ver to turn f tt ng (A)
clockw se to f x, repeat for all drawers.
1.
Step Eleven
Pos t on panel (13) as shown, turn lock ng nuts (B) clockw se to lock.
1.

Page 9
NAN 04/14
O1
O2
HH
O2
14
14
15
F
F
A
7
5
6
Step by step assembly instructi ns
Step Twelve
F x runner parts (O1) (O2) to the panels (14) (15)
through holes shown n the deta l v ew
us ng 4x euroscrews (H).
1.
Step Thirteen
Attach 10x metal dowels (A) nto the pre-dr lled holes on panels.
Use a screwdr ver to turn f tt ng (A) clockw se to f x.
Attach 4x wooden dowels (F) nto the pre-dr lled holes of panel (7) as shown.
1.
2.

Page 10
NAN 04/14
7
5
6
1
2
B
A
7
5
6
Step by step assembly instructi ns
Step Fourteen
Attach panels as shown.
Ensure wooden dowels are al gned correctly w th the holes of match ng parts before attach ng.
1.
Step Fifteen
Pos t on panels as shown, turn lock ng nuts (B) clockw se to lock.
1.

Page 11
NAN 04/14
P
P
P
Q
8
8
P
P
Q
8
8
P
I
N
8
8
I
N
S
S
N
I
LIFT STAY ASSEMBLY
Make sure triangle plate is positioned as
per image
Step by step assembly instructi ns
Step Sixteen
F x plast c h nge (P) to m rror panel (8) us ng screw (Q)1.
F x m rror panel (8) to desk us ng plast c h nge (P) and screw (Q) 2.
Step Seventeen
F x the two Arms (N) us ng 8x screws (I)
Attach bumpers (S)
1.
2.

C
E
E
C
C
A
11
10
12
9
L
L
11
10
9
Page 12
Step by step assembly instructi ns
Step Eighteen
Attach 2x wooden dowels (E) nto the pre-dr lled holes on drawer backs (11) as shown.
Place the cam lock (C) nto the holes on drawer s des (9) (10) as shown, arrow po nt ng
towards the bolt.
Attach 2x metal dowels (A) nto the pre-dr lled holes on drawer front (12). Use a screwdr ver to
turn f tt ng (A) clockw se to f x.
Repeat for all drawers.
1.
2.
3.
Step Nineteen
F t the RH (10) and LH (9) drawer s des to the drawer back (11) us ng 30 mm screws (L).
Repeat for all drawers.
1.
NAN 04/14

2
C
1
C
A
10
12
9
18
Page 13
NAN 04/14
Step by step assembly instructi ns
Step Twenty
Sl de drawer bottom panel (18) nto the drawer box grooves.
Pos t on drawer front (12) onto drawer box, turn lock ng nuts (C) clockw se to lock.
Repeat for all drawers.
1.
2.
Step Twenty-one
Pull out the runners, then ensure plast c secur ng pegs are to the OUT pos t on.1.

Page 14
Step by step assembly instructi ns
Step Twenty-two
Sl de the drawer box t lted unt l the stop.
Attach the drawer box lean ng on the runners.
Push the plast c secur ng pegs n the IN pos t on
1.
2.
3.
NAN 04/14

Page 15
NAN 04/14
3
Step by step assembly instructi ns
Step Twenty-three
Use the small plast c knob of the runners to al gn the drawers f needed.1.
Step Twenty-four
To prevent poss ble overbalanc ng we recommend that th s un t s secured to a su table wall
by us ng appropr ate wall plug and screw (not ncluded) and the two holes nto back panel (3).
See wall f x ngs gu de at the end of booklet.
1.

Page 16
NAN 04/14
Wood
If xing to wood
make sure that it
isn't chipboard as
screws can easily
pull away from the
core structure
Brick or Masonry
Use an appropriate
wall plug provided you
are sure your wall is
sound.
Cavity wall
Special toggle
wall plugs are
needed. Seek
expert advice.
Wall fixing - if in d ubt seek pr fessi nal advice
Care and Maintenance
Safety Instructi ns
his product has been manufactured using modern manufacturing methods and materials.
o keep your product, looking at its best, we strongly recommend either dusting with a soft cloth, or
the use of a damp (not wet ) cloth and water containing no more than a 5% soap solution.
Dry with a soft clean cloth.
Aggressive chemicals, such as wax furniture polish, abrasive cleaners, bleach or hypochlorate (chlorine)
based cleaners, multi purpose cleaners, dilutes, acetone, alcohol and solvent based liquid product should
NO be used, as may result in damage.
Never drag furniture when moving it, always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten when necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a competent person. No
liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
It is recommended that before moving a heavy object to a new location it is completely dis-assembled to avoid
personal injury or damage to the furniture. Please be careful to retain all fittings when doing this.
his product is designed to be fixed securely to a sound wall in the manner stated.
It must under no circumstances be used free-standing. No liability will be accepted for damage or injury caused by
inadequate fixing or use without fixing.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
John Lewis Partnership 171 Victoria Street London SWIE 5NN
www.johnlewis.com