John Lewis Mixit User manual

Please check the pack contents before attempting to assemble this product. A full checklist of compo-
nents is given in this leaflet. If any components are missing, please contact your the John Lewis Helpline.
his product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
his product takes approximately 90 MINUTES to assemble with 2 PEOPLE.
he fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
If you are missing some fittings please contact our spare parts helpline on 0330 005 9435.
Opening hours are 9am - 5pm Monday to Friday.
John L wis
Stock Code: 80319005 - 80319105 - 80319205
Mixit wardrob
hank you for purchasing this Mixit wardrobe. Please read the instructions carefully before use to en-
sure safe and satisfactory operation of this product.
PRE-ASSEMBLY PREPARATION
Please ensure instructions are read in full before attempting to assemble this product.
N c ssary Tools
Screwdriver
002030405060708090 00 020 30 40 50
023456
Ruler/tape
measure Small hammer
Drill Eye protection
Spirit level
MXT 01/13
Page 1

Metal dowel x 12 Cam lock x 12 Wooden dowel x 16
30mm
Wedgex housing x 4 Wedgex dowel x 4 Support foot x 4
Hanger rail support x 2 11mm Euroscrew x 4 15mm Screw x 2
Spacer x 2 x 2 Levelling Wedge x 2
Bumper x 4 25mm Nail x 30 27mm Connector x 4
4MAx15 Connect. screw x 4 hanging rail x 1 Nail guide x 1
clip hinge x 6 hinge mounting plate x 6 15mm screw x 12
A B C
G
L
H
M
R S
P1
D E F
I
N
O P Q
T I U
Page 2
MXT 01/13
Fittings he klist

1
1
2
2
3
4
5
6
Page 3
MXT 01/13
Parts he klist

C
B
C
1x 2
B
5
CC
6Raw
Page 4
Step by step assembly instru tions
Step One
Attach 4x wooden dowels (C) into the pre-drilled holes on top/bottom panels (1) as shown.
Place the cam lock (B) into the holes on top/bottom panels (1) as shown, arrow pointin towards the
bolt.
1.
2.
Step Two
Attach 8x wooden dowels (C) into the pre-drilled holes on rails (5) (6) as shown.1.
D
3
D
Step Three
Attach 4x wed efix housin (D) into the pre-drilled holes on shelf (3) as shown.1.
MXT 01/13

1
6
7
6
1
7
33
3332
34
59
59
Right side
left side
Bottom
Bottom
60
60
F
U
2
A
F
U
2
A
U
U
Page 5
MXT 01/13
Step by step assembly instru tions
Step Four
Attach 12x metal dowels (A) into the pre-drilled holes on side panels (2) as shown. Use a screwdriver to
turn fittin (A) clockwise to fix.
Attach 4x support foot (F) into pre-drilled holes on side panels (2) as shown.
Attach 6x hin e mountin plate (U) into pre-drilled holes on side panels (2) as shown. Pay attention to
place central hin e at correct position.
Holes count starts from the bottom.
1.
2.
3.

1
1
2
5
6
12
B
A
B
1
1
2
5
6
12
B
B
A
Page 6
Step by step assembly instru tions
Step Five
Attach top/bottom panels (1) and rails (5) (6) onto ri ht side (2) as shown. Ensure metal dowels (A) and
wooden dowels (C) are ali ned correctly with the holes of matchin parts before attachin .
Secure top/bottom panels (1) to ri ht side panel (2) usin a screwdriver to turn fittin (B) clockwise to fix.
1.
2.
Step Six
Attach top/bottom panels (1) and rails (5) (6) onto left side (2) as shown. Ensure metal dowels (A) and
wooden dowels (C) are ali ned correctly with the holes of matchin parts before attachin .
Secure top/bottom panels (1) to ri ht side panel (2) usin a screwdriver to turn fittin (B) clockwise to fix.
1.
2.
MXT 01/13

P
P
P
Important:
The cabinet MUST
be ‘square’ when the
back is attached.
4
P1
4
Page 7
MXT 01/13
Step by step assembly instru tions
Step Seven
With help of an assistant,
carefully rotate the unit.
1.
Step Eight
Position back panel (4) as shown.
1.
Step Eight
Attach back panel (4) onto back side of the unit usin 30x nails (P), with the help of the nail uide (P1).
1.

N
N
Page 8
Step by step assembly instru tions
Step Nine
With help of an assistant, carefully stand up the unit upri ht.1.
Step Ten
Use 2x levellin wed e (N) to level the unit.1.
MXT 01/13

Ø5mm
RQ
Page 9
MXT 01/13
Step by step assembly instru tions
Step Eleven
Fittin s have been supplied in order to join units to ether.
Place units to ether in their final positon.
Decide position where to drill throu h usin a Ø5 mm bit.
Push the Connector (Q) into the hole and then screw Bolt (R) in from the other side, ti hten with a
screwdriver.
1.
2.
3.

L
M
I
Wall plug
and screw
not included.
Please see
Guide to
wall mounting
20 mm
M
I
L
Page 10
MXT 01/13
Step by step assembly instru tions
Step Twelve
To prevent possible overbalancin we recommend that this unit is secured to a suitable wall by use of two ‘L’
Brackets (M) fitted to the Top of the unit.
Fix the Brackets (M) loosely onto the top of the unit usin spacer (L) screw (I) and mark the wall for the wall fix-
in .
Swivel the Bracket (M) away from the wall and drill a hole in the wall usin a suitable drill bit and fit your wall
fixin .
Swivel the Bracket (M) back and fix the Bracket to the wall, then ti hten Screw (I)
! IMPORTANT !
Take care when drillin the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Wall plu and screw not included. See wall fixin uide at pa e 14.
1.
2.
3.