John Lewis Kingsley 803572/01 User manual

1
John Lewis
Kingsley Bed
Stock number: 803572/01
02/03/10/11/12/13/14/15
Thank you for purchasing this Kingsley Bed. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product
Pre-assembly preparation
Please ensure instructions are read in full before attempting to assemble this product
Necessary Tools
For Spare Parts please contact the
Whitemeadow John Lewis Customer
Services on 01623 552495

2
Please check the pack contents before attempting to assemble this product. A full checklist of
components is given in this leaflet. If any components are missing, please contact the
Whitemeadow John Lewis Customer Services line, which is located above.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE
CARE WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 30 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG
CHILDREN.
Read this leaflet in full before commencing assembly.
Fittings and parts checklist
A
6x
Mounting
brackets
G 4x split
rings
B 1x Central
beam H 4x wing nuts
C 2x Allen
key bolts I
10x
small
washers
D 5x Felt
pads J
E 4x Hex
head bolts K
F 4x Rubber
washers L

3
Step by step assembly instructions
Step One
1. Build the slatted steel bed base following the instructions provided within.
______________________________________________________________
Step Two
1. Packaged with the side panels you will find the bed feet.. Fit these into the threaded hole
on the base of the head and footboard by turning clockwise. DO NOT OVERTIGHTEN.
____________________________________________________________________________________________________
Step Three

4
1. Lean the headboard against a wall or with the aid of another person, loosen the 4 allen
bolts and lift the side panel into place by sliding the corner bracket across and down onto
the bolts as shown. Ensure washers sit in front of the bracket.
2. Repeat with the footboard.
3. Using the allen key provided, tighten all 8 bolts evenly. DO NOT OVER TIGHTEN
Step 4
1. Take bracket ‘A’ and slot into the notched steel plates on the head/footboard and side
panels by pushing in and down as shown. Select your preferred mattress height using the
corresponding slot and ensure that the 4 brackets on the side rails are positioned at the
same height. The bracket on the head and foot boards MUST be positioned 1 SLOT LOWER
than the brackets on the side rails.
Step 5
A
A
A
A

5
1. Take the Centre beam ‘B’ and lay onto the two brackets ‘A’ positioned on the head and foot
boards. Use the allen keys provided to secure in place from beneath with bolt ‘C’ and
washer ‘I’ at both ends.
2. Apply 5x sticky back pad ‘D’, evenly spaced along the length of the centre beam ‘B’.
Step 6
1. Place 1x rubber washer ‘F’ onto each of the 4 brackets ‘A’ positioned on the side rails and
lower the assembled slatted base into the bed frame. Align holes on the steel bed base with
the holes on brackets ‘A’.
2. Insert bolt ‘E’ with washer ‘I’ on top and bottom, followed by washer ‘G’ and hand tighten
with wing nut ‘H’.
Care and Maintenance
D
B
B
I
C
E
I
I
G
H
F

6
Wooden Feet
Wood displays different grain patterns depending on which way they cut - for example, the
‘medullary ray’ which can appear on oak furniture is a mark of good quality timber - these are
just characteristics of the natural beauty of the wood. Some furniture is also deliberately aged
and rustic.
All timber surfaces will change colour and mellow over time. New furniture will initially vary in
shade from items that have been previously purchased.
Metal and Fabric
Protect fabrics from spillage, sunlight and heat. A slightly damp cloth is the best cleaning agent
for both materials.
Do not use any abrasive cleaner or harsh detergent as this can damage the surface.
Avoid spilling or dropping crumbs of food with a high fat content on the surface as this can
permanently mark the fabric.
Safety Instructions
General warnings:
Never drag furniture when moving it, always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a competent
person. No liability will be accepted for damage or injury caused by incorrectly insalled or assembled
furniture.
Specific warnings for heavy items:
It is recommended that before moving heavy objects to a new location they are completely dis-
assembled to avoid personal injury or damage to the furniture. Please be careful to retain all fittings
when doing this.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
John Lewis Partnership 171 Victoria Street London SW1E 5NN
www.johnlewis.com