John Lewis 80307108 User manual

1of 12
John Lewis
Maine white/ash 2 door wardrobe
Stock number: 80307108
Thank you for purchasing this Maine 2 door wardrobe. Please read the instructions carefully before use
to ensure safe and satisfactory operation of this product
Pre-assembly preparation
Please ensure instructions are read in full before attempting to assemble this product
Necessary Tools
You will require a cross head screwdriver to assemble this product. An electric drill may cause damage
to the product and is not recommended.
Please check the pack contents before attempting to assemble this product. A full checklist of
components is given in this leaflet. If any components are missing, please contact John Lewis customer
services or your local branch.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 70 MINUTES to assemble with /2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG
CHILDREN.
Read this leaflet in full before commencing assembly.

2of 12
Fittings and parts checklist
A
Top x 1 B Left side panel x 1
C
Right side panel x
1
D Door x 2
E
Bottom piece
front x 1 F
Bottom x 1
I
J
A
D
C
D
B
E
F
GG
G
G
H
I

3of 12
G
Back panel part x
4
H
Middle piece back
x 1
I Back panel list x 2
J 19x786mm Pole x
1
K
8x35mm wooden
dowel x 12 L
6x45mm Minifix
bolt x 9
(For wood)
M
6x45mm Minifix
bolt x 12
(For bushing)
N
Minifix housing x
21
O
Mounting plate x
6
P Cup hinge x 6
Q
4x12mm screw x
24 R
4x25mm screw x
2
S 3x15mm screw x
16 T
Counter plate
oval x 4
U Magnet x 4 V 19mm Nail x 60
W
(Rail holder part
one) x 2
X
(Rail holder part
two) x 2
Y Knob x 2 Z
4x25mm dome
screw x 4
____________________________________________________________________________

4of 12
Step by step assembly instructions
Step One
Fix the six minifix bolt (M) to the top (A) as shown
Fix the two magnets (U) to the top as shown with 4 screws (S). Let them sit loose until the doors are
fixed in step thirteen.
____________________________________________________________
Step Two
Fix the six dowels (K) into the bottom (F) as shown
Fix the two magnets (U) to the bottom as shown with 4 screws (S). Let them sit loose until the doors
are fixed in step thirteen.
____________________________________________________________________________
Fittings
M X 6
S X 4
U X 2
A
S
U
U
M
M
M
M
M
M
SSS
K
SSS
K
K
K
K
K
F
S
U
U
Fit
tings
K X 6
S X 4
U X 2

5of 12
____________________________________________________________________________
Step Three
Fit the two dowels (K) into the end of the bottom piece front (E)
Fix the three minifix bolt (L) to the bottom piece front as shown
____________________________________________________________________________
Step Four
Fit the bottom piece front (E) against the bottom (F)
Use three minifix houseings (N) to fasten the bottom piece front to the bottom
____________________________________________________________________________
Fittings
K X 2
L X 3
Fittings
N X 3
E
F
N
N
N
X3
K
K
E
L
L
L

6of 12
____________________________________________________________________________
Step Five
Fit the two dowels (K) into the top end of the left side panel (B) as shown.
Fix the three minifix bolt (M) to the side as shown
Fix the three minifix bolt (L) to the legs parts of the side panel as shown
Fix the rail holder part one (W) to the side, for that use 25mm screw (R)
Fix the three mounting plates (O) to the side, for that use six screws (Q)
____________________________________________________________________________
Fittings
K X 2
L X 3
M X 3
O X 3
Q X 6
R X 1
W X 1
Front
Back
LL
Q
Q
O
O
Q
Q
OQ
Q
O
Q
Q
K
K
B
R
W
M
M
M
L

7of 12
____________________________________________________________________________
Step Six
Fit the two dowels (K) into the top end of the right side panel (C) as shown.
Fix the three minifix bolt (M) to the side as shown
Fix the three minifix bolt (L) to the legs parts of the side panel as shown
Fix the rail holder part one (W) to the side, for that use 25mm screw (R)
Fix the three mounting plates (O) to the side, for that use six screws (Q)
____________________________________________________________________________
M
M
M
L
L
L
QQ
OFront
Back
O
QQ
O
QQ
O
QQ
K
K
C
R
W
Fittings
K X 2
L X 3
M X 3
O X 3
Q X 6
R X 1
W X 1

8of 12
____________________________________________________________________________
Step Seven
Lay the left side panel (B) on the floor
Fit the middle piece back (H) to the leg part of the left side panel as shown
Fit the assembled bottom and bottom piece front (E&F) into the left side panel as shown
Place the right side panel (C) so it does fit in the holes of the middle back piece (H) and bottom
Fix the twelve minifix housings (N) as shown
____________________________________________________________________________
Step Eight
Place the top (A) so it does fit in the holes of the side panels (B&C)
Fix the six minifix housings (N) as shown
____________________________________________________________________________
Fittings
N X 12
Fittings
N X 6
X12
B
C
H
F
E
N
N
N
N
N
N
N
N
NNNN
A
N
N
NNNN
X6

9of 12
____________________________________________________________________________
Step Nine
Place the rail holder part two (X) in both ends of the pole (J) as shown
____________________________________________________________________________
Step Ten
Place the pole (J) and rail holders part two (X) in position as shown, and screw it on rail holder part one
(W)
____________________________________________________________________________
Fittings
X X 2
X
XJ
J
X
J

10 of 12
____________________________________________________________________________
Step Eleven
Fit the four back panels (G) in position back on the wardrobe as shown
To fasten it use nails (V)
Connect two back panels with the back panel list (I), this for both upper section and lower section.
____________________________________________________________________________
Step Twelve
Fix three cuphinges on each of the two doors (D), for that use screws (Q)
Fix two counter plates (T) on each of the two doors, for that use srews (S)
Fix the knob (Y) on each of the two doors, for that use dome screws (Z)
____________________________________________________________________________
GG
G
G
I
I
Fittings
V X 60
D
P
P
PP
QQ
S
S
T
S
T
S
Z
Z
Y
Fittings
P X 6
Q X 12
S X 8
T X 4
Y X 2
Z X 4
X 2

11 of 12
____________________________________________________________________________
Step Thirteen
Fix the right and left doors (D) to the wardrobe by connecting the cup hinges (P) to the mounting
plate (O)
The way doing that, is to push the cuphinges inwards over the mounting plates and fasten it with screw
as shown.
Fasten the magnets (U) when the doors are in the right position
____________________________________________________________________________
DD
u

12 of 12
Care and Maintenance
This Maine wardrobe should be cleaned using a soft damp cloth and dried immediately.
Do not use a very wet cloth or allow any liquid to contact with the veneers for a
long period of time as this can permanently damage the surface. Do not use any
abrasive cleaner or harsh detergent as this can damage the surface of the veneers.
Safety Instructions
General warnings:
Never drag furniture when moving it, always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten when necessary.
Please take care when handling or moving the furniture as careless handling may cause
damage or injury.
Furniture can be dangerous if incorectly installed. Assembly should be carried out by a
competent person. No Liability will be accepted for damage or injury caused by incorrectly.
Specific warnings for heavy items:
It is recommended that before moving heavy objects to a new location they are completely dis-
assembled to avoid personal injury or damage to the furniture. Please be careful to retain all fittings
when doing this.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
John Lewis Partnership 171 Victoria Street London SW1E 5NN
www.johnlewis.com