John Thomas OF-69 User manual

ITEM NO.: OF-69
REVISED MAR 15, 2021
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: SERENDIPITY DESK
: OF-69

ITEM NO.: OF-69
REVISED MAR 15, 2021
Printed in Vietnam
- 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your table. Protect the surface of the table with cloth if you are using any product
with rubber feet or base.
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: OF-69
REVISED MAR 15, 2021
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
C
Support Bar
(L-R)
2
B
Side Frame
(L-R)
2
D
Crossbar
1
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Short Bolt
(M6 x 35mm)
8
7
Allen key
(M4 x 30 x 110mm)
1
2
Small Lock Washer
(ɸ6.5 x 11mm)
8
8
Screw
(M4 x 50mm)
2
3
Small Flat Washer
(ɸ6.5 x 19mm)
8
9
Handle
2
4
Long Bolt
(M8 x 45mm)
4
10
Pan head screw
(M4 x 20mm)
4
5
Large Lock Washer
(ɸ8.5 x 13mm)
4
11
USB charger
1
6
Large Flat Washer
(ɸ8.5 x 19mm)
4
12
Power Adapter
1

ITEM NO.: OF-69
REVISED MAR 15, 2021
Printed in Vietnam
- 4 -
STEP 1
Pull out the drawers. Attach side frames (B) to the top (A) with bolts (1), and washers (2) and (3), as
shown below. Tighten with Allen key (7).
STEP 2
Attach support bars (C) to top (A) and side frames (B) with bolts (4), and washers (5) and (6) as shown
below. Tighten with Allen key (7).
Insert crossbar (D) into support bars (C) as shown below and attach with screws (8). Tighten with a
screwdriver.

ITEM NO.: OF-69
REVISED MAR 15, 2021
Printed in Vietnam
- 5 -
STEP 3
Attach handles (9) to front of drawers with pan head screws (10) as shown below. Tighten with a
screwdriver.
STEP 4
Insert USB charger (11) into the top (A), as shown below.

ITEM NO.: OF-69
REVISED MAR 15, 2021
Printed in Vietnam
- 6 -
STEP 5
Plug the power adapter (12) into cable of the USB charger (11) inside the top, as shown below.