Juniper Mist AP12 Manual

1
AP12 Hardware Installation Guide
Juniper Networks, Inc. (C) Copyright 2020. All Rights Reserved
AP12 Hardware Installation Guide
Overview
The Mist AP12 contains three IEEE 802.11ax radios that deliver up to 2x2
MIMO with two spatial streams when operating in multi-user (MU) or single-
user (SU) mode.

2
AP12 Hardware Installation Guide
Juniper Networks, Inc. (C) Copyright 2020. All Rights Reserved
I/O ports
Reset Reset to the factory default settings
Eth0+PoE 10/100/1000BASE-T RJ45 interface that supports 802.3at
PoE PD
Pass Thru Passive RJ45 Pass Thru (rear to bottom)
Eth1+PSE 10/100/1000BASE-T RJ45 interface with Class 2 PSE out
(enabled if you have 802.3at PoE input on Eth0)
Eth2-Eth3 10/100/1000BASE-T RJ45 interfaces

3
AP12 Hardware Installation Guide
Juniper Networks, Inc. (C) Copyright 2020. All Rights Reserved
AP12 Mounting

4
AP12 Hardware Installation Guide
Juniper Networks, Inc. (C) Copyright 2020. All Rights Reserved
Technical Specifications:
Feature Description
Power options 802.3at/802.3af PoE
Dimensions 100mm x 150mm x 40mm (3.93in x 5.91in x 1.57in)
Weight 0.6 kg (1.32 lbs)
Operating
temperature 0° to 40° C
Operating humidity 10% to 90% maximum relative humidity, non-condensing
Operating altitude 3,048m (10,000 ft)
I/O
1 – 10/100/1000BASE-T auto-sensing RJ-45 with PoE In
1 – 10/100/1000BASE-T auto-sensing RJ-45 with PoE Out
2 – 10/100/1000BASE-T auto-sensing RJ-45
Pass Thru from the rear to the bottom I/O area
RF
5GHz - 2x2:2SS 802.11ax MU-MIMO & SU-MIMO
2.4GHz – 2x2:2SS 802.11ax MU-MIMO & SU-MIMO
2.4GHz / 5GHz scanning radio
2.4GHz BLE with Omni Antenna
Maximum PHY rate
Total maximum PHY rate – 1775 Mbps
5GHz – 1201 Mbps
2.4GHz – 574Mbps
Indicators Multi-color status LED
Compliance standards
CAN/CSA-C22.2 No. 62368-1-14
FCC Part 15.247, 15.407, 15.107, and 15.109
RSS-247
ICES-003 (Canada)

5
AP12 Hardware Installation Guide
Juniper Networks, Inc. (C) Copyright 2020. All Rights Reserved
Warranty Information
The AP12 Access Point comes with a limited lifetime warranty.
Ordering Information:
Access Points
AP12-US 802.11ax 2+2 Wall Plate AP – Internal Antenna for the
US Regulatory domain
AP12-WW 802.11ax 2+2 Wall Plate AP – Internal Antenna for the
WW Regulatory domain
Mounting brackets
APBR-WP1 Bracket for AP12
APBR-DS1
Desk stand for AP12

6
AP12 Hardware Installation Guide
Juniper Networks, Inc. (C) Copyright 2020. All Rights Reserved
Regulatory Compliance Information:
This product and all interconnected equipment must be installed indoors within the same
building, including the associated LAN connections as defined by the 802.3at Standard.
If you need further assistance with purchasing the power source, please contact Juniper
Networks, Inc.
FCC Requirement for Operation in the United States of
America:
FCC Guideline for Human Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 25
cm between the radiator & your body.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
● Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
● This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.

7
AP12 Hardware Installation Guide
Juniper Networks, Inc. (C) Copyright 2020. All Rights Reserved
Industry Canada
This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
Ce dispositif est conforme à la norme CNR-247 d'Industrie Canada applicable aux appareils
radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1)
le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit
accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un
fonctionnement indésirable.
This radio transmitter (IC: 22068-AP12 / Model: AP12) has been approved by ISED to
operate with the antenna type listed below with maximum permissible gain indicated.
Antenna types not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (IC: 22068-AP12 / Model: AP12) a été approuvé par ISED pour
fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible
maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au
gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
Approved antenna(s) list:
Antenna No. Brand Model Antenna Net
Gain (dBi)
Frequency
range (GHz) Antenna Type Connector Type
Int WiFi Dual
Ant
3
6
2.4 – 2.484
5.15 – 5.85 Omnidirectional N/A
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 29
cm between the radiator & your body.
Déclaration d'exposition aux radiations:Cet équipement est conforme aux limites
d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec un minimum de 29 cm de distance entre la
source de rayonnement et votre corps.

8
AP12 Hardware Installation Guide
Juniper Networks, Inc. (C) Copyright 2020. All Rights Reserved
IC Caution
(i) The device for operation in the band 5150-5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems;
(ii) The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and
5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
(iii) The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be
such that the equipment still complies with the e.i.r.p. limits specified for point-to-point
and non-point-to-point operation as appropriate; and
(iv) Users should also be advised that high-power radars are allocated as primary users
(i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these
radars could cause interference and/or damage to LE-LAN devices.
Avertissement
Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions
précises sur les restrictions susmentionnées, notamment :
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement
pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux
systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) le gain maximal d'antenne permis pour les dispositifs utilisant les bandes de 5250 à 5
350 MHz et de 5470 à 5725 MHz doit être conforme à la limite de la p.i.r.e;
(iii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5 725 à 5
850 MHz) doit être conforme à la limite de la p.i.r.e. spécifiée pour l'exploitation point à
point et l’exploitation non point à point, selon le cas;
(iv) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de
haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour
les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du
brouillage et/ou des dommages aux dispositifs LAN-EL.