JUPITERBIKE SUMMIT User manual

Folding Electric Bike | Vélo Pliant Electric | Bici Eléctrica Plegable
USERS MANUAL

1
Structural Diagram ...................................................... 2
Specications ................................................................. 3
Installing the Front Wheel ...................................... 4
Installing the Handlebars ....................................... 5
Seat Post Installation ................................................. 6
Pedals Installation ....................................................... 6
Removing the Battery ............................................... 7
Fender Installation ...................................................... 7
Turning On Your Bike ................................................. 8
The LCD Display ........................................................... 8
Precautions When Riding ....................................... 9
Warnings ......................................................................... 10
Warranty .......................................................................... 11
Returns & Exchanges .............................................. 11
TABLE OF
CONTENTS
Folding Electric Bike | Vélo Pliant Electric | Bici Eléctrica Plegable

2
HANDLE
BIKE FRAME
LATCH
SADDLE
SEAT POST
SEAT POST
CLAMP
SHOCK
ABSORBER
MOTORPEDAL
BRAKE
STEM
BIKE FRAME
FRONT FORK CHAINWHEEL
DISC
BRAKE
DERAILLEUR
DISPLAY
STRUCTURAL DIAGRAM
NOTE:
Manual illustrations are for demonstration purposes only. Illustrations may not reflect exact
appearance of actual product. *Specifications subject to change without notice.*
Tire Pressure: 40-60 psi
*Mileage is subjected to weight, road conditions, temperature,
wind speed, riding habits, etc. The bike was tested on speed 1
in conditions, which consisted of: 143 lb Load, 77°F temperature,
riding on flat road, wind less than .5 mph and with full charge.
*Please use the original charger that was provided with purchase.
*The warranty becomes invalid in the instance of any unauthor-
ized bike modification.

3
PACKING CONTENTS:
Summit Electric Bike
Saddle & Seat Tube
User Manual
Charger
In Frame Battery
2 Keys for Battery Lock
Rear Mudguard
Multi-Purpose Bike Tool
SPECIFICATIONS
MOTOR & BATTERY
Motor Wattage: 48V / 500w
Charging Time: About 5 hours
Waterproof Rating: IP54
Battery Capacity: 48V / 7Ah
Battery Type: Lithium Ion
Charging Current 2A max
METER:
Display: LCD Display
Remaining Power: Yes
Speed: Yes
Total Mileage: Yes
Speed Mode: 5 Speed Levels
COMPOSITION
Suspension: Front Spring Shock Absorber
Frame: Aluminum Alloy Unibody Frame
Brake Type: Front & Rear Disc
Production dimensions:
Folded: H = 42”, W = 24”, L = 40”
Unfolded: H = 43”, W = 25”, L = 73”
Seat Height (from ground) 34” - 41” (adjustable)
Net Weight (with battery) 51 lbs
Wheel Base: 45 Inches
Tire Size: 26” x 2.35”

4
INSTALLING THE FRONT WHEEL
Remove parts from box and locate
the front wheel and front wheel
axle.
Unscrew the thumb screw on the
axle, place the axle in the front
wheel, then loosely re-screw it.
Place the front fork on to the axle.
Make sure the Axle Latch is open.
Hand tighten the thumb screw,
then close the Axle Latch. Test and
make sure the wheel does not
wobble.

5
INSTALLING THE HANDLEBARS
Loosen screws 1 and 2,
then turn the handlebar
stem to the front.
Remove the 4 screws on
the top cover, then remove
the cover.
Attach the handlebars onto the handlebar stem and tighten screws.

6
SEAT POST INSTALLATION
Unlatch and loosen seat
clamp. Put seat post in
frame and adjust to desired
height. Retighten and re-
latch clamp.
PEDALS INSTALLATION
Install the pedal with the L
on it on the left side of the
bike. It should hand twist
easily on the pedal arm. If
it doesn’t, it might not be
going in straight. Unscrew it
and try it again.
Use a wrench for the last
1 or 2 turns. Repeat with
the R pedal on the other
side. The R pedal is reverse
threaded so twist in the
opposite direction.

7
Unlatch the Bike Frame Latch and fold
the bike in half. The frame has a metal
stand under the Chainring that the bike
will balance on when folded.
Use the included keys to unlock the
battery, then gently pull the battery out
of the frame. The battery can be charged
inside or outside the frame. Please be
careful not to lose the keys. Do not store
the battery on empty.
REMOVING THE BATTERY
FENDER INSTALLATION
Attach the fender to the bike
frame so it’s positioned above the
rear tire. Use the included hex bolt
and nut to secure the fender to
the frame.

8
Once the bike is
charged, open the
battery frame access
panel and switch the
power On.
Next, press the power
button on the button
panel. Congratulations!
You bike is ready.
Don’t Forget! Practice
common sense &
safety measures when
riding your bike.
THE LCD DISPLAY
TURNING ON YOUR BIKE
Download the complete display manual at jupiterbike.com/summit for detailed instructions.

9
PRECAUTIONS WHEN RIDING
Do not ride in snowy
or slippery road
conditions.
Always ride with
both hands on the
handlebar.
Never ride down stairs,
escalators orelevators.
• Wear the appropriate protection gear such as helmets, knee pads, and elbow pads on
your rides to help prevent injury.
• Inspect the bike, brakes, & battery before each ride to ensure all is in working order.
• Do not ride on slopes over 15°
• If you must ride in the rain or snow, please ride at lower speeds and keep a safe stopping
distance from objects and vehicles in front of you.
• Children under the age of 16 are not advised to ride the bike.
• Avoid sudden starts and stops.
• Do not lean forwards or backwards while riding, and maintain a safe speed at all times.
• If the battery runs low, keep a low constant speed & charge the battery as soon as possible.
• Do not store your bike in the trunk of a car in hot weather.
• Have a full understanding of local traffic rules and regulations before you ride.
• Be aware of your surroundings at all times, and be sure to always ride in safe conditions.
• Keep a comfortable distance from other riders.
• Use caution when riding in environments with low visibility, if necessary, lower your speed or
stroll your bike.
• Do not ride the bike backwards or do any actions that may endanger yourself and others
while riding.
• Do not lend your bike to others without letting them become familiar to this manual first.
• Do not ride while ill or under the influence of drugs or alcohol.
• Accelerate slowly when riding. Sudden acceleration may throw you out-of-balance and could
cause falls or injury.

10
• For your safety, please read the user manual
carefully. Make sure the owner and operator
understand and accept all the safety instructions.
• Ride at your own risk and use common sense. You
will be responsible for any loss or damage caused
by improper use.
• The elderly, pregnant women, children, and those
with heart conditions should not use this product.
• Do not exceed the weight limit of 265 pounds. Only
1 rider at a time.
• Inspect each part of the product prior to each use
to ensure that it has been correctly maintained
and is properly functioning. Riding with improperly
adjusted brakes is dangerous and may result in
serious injury or death.
• Only operate in safe, suitable locations. Do not
ride on roads with obstacles, such as litter, small
stones, etc. Avoid riding on steep slopes or in
narrow areas. Avoid riding in the rain or on smooth
slippery surfaces such as ice or snow. Avoid riding
near flammable gas, steam, liquid or dust that
could cause a fire.
• If you have had any head, neck or back ailments,
or prior surgeries to those areas, Do Not ride this
product.
• Do not ride without proper training, at high speeds,
on uneven terrain or on slopes.
• Be sure all safety labels are in place and
understood prior to riding.
• Do not use near motor vehicles.
• Do not ride after taking prescription medications
or drinking.
• Do not answer your phone, carry items or engage
in any other activities while riding.
• Always wear appropriate safety gear, including
shoes and a helmet. We encourage you to use
lighting, reflectors and signal flags.
• Always comply with laws, regulations and
ordinances, including local traffic laws.
• Always give way to pedestrians, and be alert to
your surroundings, both directly in front of you and
in the distance.
• When riding with others, always maintain a safe
distance to avoid the possibility of a collision.
• Be sure to maintain your balance when turning,
and don’t make sharp turns.
• Applying the brakes too hard, or suddenly, can
cause a wheel to lock which may cause you to lose
control and fall which may result in injury or death.
• Only ride the product with adequate daylight for
visibility.
• Do not lift the product from the ground while it is
on and the wheels are in motion. This may result
in free spinning wheels which may cause injury to
yourself or others.
• Do not jump on or off the product or jump while
using it, or perform stunts.
• When not in use, store your bike in a cool, dry area
away from sunlight and water.
• To clean your bike, use a soft damp cloth to wipe
clean, and dry with a dry cloth. To protect internal
wiring and electric components, do not soak
or rinse your bike with water, and do not clean
your bike with corrosive or flammable chemical
solvents, like alcohol, gasoline, paraffin or acetone.
• Do not attempt to disassemble, modify, repair or
replace the unit or any components of the unit
without instruction from Customer Support. This
will void any warranty and can lead to malfunctions
that may cause injury.
CALIFORNIA PROPOSITION 65
WARNING:this product can expose you to a chemical
such as Cadmium that is known to the State of
California to cause cancer or birth defects or other
reproductive harm. For more information go to:
www.p65warnings.ca.gov/product
TROUBLESHOOTING
For troubleshooting or operational issues, please
contact Jupiter Tech at 813-609-BIKE (2456) or
e-mail sales @jupiterbike.com
SAFETY WARNINGS

11
JUPITER BIKE SUMMIT – LIMITED 1 YEAR WARRANTY
The Jupiter Bike Summit and accessories are manufactured to high quality standards.
The Jupiter Bike Summit is warranted to the original purchaser for one full year from
the original purchase date against defective materials or workmanship. This warranty
applies to replacement parts only and specifically excludes the tire tread, battery, and
wear parts. This warranty becomes void if the original purchaser transfers the product
to another individual.
If the Jupiter Bike Summit suffers damage due to customer modifications and/
or is used for any application other than for which it was designated, this warranty
is void. This warranty does not include damage due to: (A) neglect, (B) accident, (C)
unreasonable use, (D) improper maintenance or (E) any other causes not attributed to
defects in material or workmanship.Any implied or otherwise explicit guarantees made
through the merchandiser of this product are not covered in this warranty coverage
agreement and are expressly disclaimed.
If you feel your Jupiter Bike Summit is not operating properly and needs a replacement
part, contact Jupiter Tech at 813-609-BIKE (2453) or email [email protected] for
assistance.
IMPORTANT NOTE:
This machine was designed for certain applications only. Jupiter Tech strongly
recommends that this machine NOT be modified and/or used for any application other
than that for which it was designated. If you have questions relative to its application,
please contact us and we will advise as to its proper use. This warranty gives you
specific legal rights, and you may also have other rights which vary
from state to state.
RETURNS & EXCHANGES:
Please refer to our website JupiterBike.com for all product exchange information &
procedures.
Please keep the original packaging.
813-609-BIKE (2453)
[email protected]om
www.Jupiterbike.com
JUPITER TECH 5600 Airport Blvd. Suite C TAMPA, FL 33634
WARRANTY:

12

13
Schéma de la structure ......................................... 14
Caractéristiques techniques ............................... 15
Installation de la roue avant .............................. 16
Installation des guidons ........................................ 17
Installation de la tige de selle .......................... 18
Installation des pédales ....................................... 18
Retrait de la batterie ................................................ 19
Installation de l’aile ................................................... 19
Allumer votre vélo .................................................... 20
L’écran LCD ................................................................... 20
Précautions à prendre lors de la conduite. 21
Avertissements ........................................................... 22
Garantie ........................................................................... 23
Retours ............................................................................ 23
TABLE DES
MATIÈRES

14
SCHÉMA DE LA STRUCTURE
REMARQUE :
Les illustrations de ce manuel ne sont données qu’à titre de démonstration. Les illustrations
peuvent ne pas refléter l’apparence exacte du produit réel. Sous réserve de modifications
Pression des pneus: 40-60 psi
* Le kilométrage est soumis au poids, aux conditions routières, à
la température, à la vitesse du vent, aux habitudes de conduite,
etc. Le vélo a été testé
dans des conditions qui consistaient en: charge de 143 lb,
température de 77 ° F, conduite sur route plate, vent inférieur à
0,5 mph et avec pleine charge.
* Veuillez utiliser le chargeur d’origine fourni avec l’achat.
* La garantie devient invalide en cas de modification non autorisée
POIGNÉE
TIGE
DÉRAILLEUR
CADRE
DE VÉLO
AMORTISSEUR
FREIN À
DISQUE
FOURCHE AVANT PÉDALE ROUE À CHAÎNE MOTEUR
LOQUET DE
CADRE DE VÉLO
SELLE
POSTE DE SIÈGE
PINCE DE TIGE
DE SELLE
FREIN AFFICHER

15
CONTENU
DE L’EMBALLAGE :
Summit Vélo Électrique
Selle et tube de selle
Manuel de l’utilisateur
Chargeur
Dans le cadre de la batterie
2 Clés de verrouillage de la batterie
Garde-boue arrière
Outil de vélo polyvalent
CARACTÉRISTIQUES
MOTEUR & BATTERIE
Puissance du moteur : 48V / 500w
Temps de charge : Environ 5 heures
Étanchéité à l’eau : IP54
Capacité de la batterie: 48V / 7Ah
Type de batterie : Lithium Ion
Courant de charge 2A maxi
MESURES :
Affichage : Écran LCD
Puissance restante : Oui
Vitesse : Oui
Kilométrage total : Oui
Mode vitesse : 5 mode
COMPOSITION
Suspension : Amortisseur arrière à ressort
Cadre : Cadre monobloc en magnésium
Type de frein : Disque avant et arrière
DIMENSIONS DU PRODUIT :
Plié : H = 42”, W = 24”, L = 40”
Déplié : H = 43”, W = 25”, L = 73”
Hauteur du siège (à partir du sol) 34” - 41” (réglable)
Poids net (avec batterie) 51 livres
Empattement : 45 pouces
Taille de pneus 26” X 2.35”

16
INSTALLATION DE LA ROUE AVANT
Retirez les pièces de la boîte et
localisez la roue avant et l’axe de
roue avant.
Dévissez la vis à oreilles sur l’axe,
placez l’axe dans la roue avant,
puis revissez-le sans serrer.
Placez la fourche avant sur
l’essieu. Assurez-vous que le
loquet de l’essieu est ouvert.
Serrez à la main la vis à oreilles,
puis fermez le loquet de l’essieu.
Testez et assurez-vous que la roue
ne vacille pas.

17
INSTALLATION DES GUIDONS
Desserrez les vis 1 et 2,
puis tournez la potence du
guidon vers l’avant.
Retirez les 4 vis du capot
supérieur, puis retirez le
capot.
Fixez le guidon sur la potence du guidon et serrez les vis.

18
INSTALLATION DE LA TIGE DE SELLE
Déverrouillez et desserrez
le collier de selle. Placez la
tige de selle dans le cadre
et ajustez à la hauteur
désirée. Resserrez et
réenclenchez la pince.
PEDALS INSTALLATION
Installez la pédale avec le L
dessus sur le côté gauche
du vélo. Il doit se tordre
facilement à la main sur
le bras de la pédale. Si ce
n’est pas le cas, il se peut
que ce ne soit pas direct.
Dévissez-le et réessayez.
Utilisez une clé pour les
1 ou 2 derniers tours.
Répétez avec la pédale R
de l’autre côté. La pédale R
est filetée en sens inverse,
donc tournez dans le sens
opposé.

19
RETRAIT DE LA BATTERIE
Déverrouillez le loquet du cadre du vélo
et pliez le vélo en deux. Le cadre a un
support en métal sous le plateau sur
lequel le vélo s’équilibre une fois plié.
Utilisez les clés fournies pour
déverrouiller la batterie, puis retirez
doucement la batterie du cadre. La
batterie peut être chargée à l’intérieur
ou à l’extérieur du cadre. Veillez à ne
pas perdre les clés. Ne stockez pas la
batterie à vide.
INSTALLATION DE L’AILE
Fixez l’aile au cadre du vélo de
manière à ce qu’il soit positionné
au-dessus du pneu arrière.
Utilisez le boulon hexagonal et
l’écrou inclus pour fixer l’aile au
cadre.