JWA MYERS 76433 User manual

Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
1
5 DRAWER TALL CHEST
MYERS
ITEM CODE 76433
800mm
400mm
1188mm

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lg. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instruons carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not ovghten the screws and bolts as this may damage the threads
Allow 45 min For person Addnal tools required
2
2

PARTS LIST
3
19
10
11
12
14 13
17
15
12
14
16
18
x3
x2
1
2
3
4
5
5
6
7
8
78
9

4
NO. ITEM QTY NO. ITEM QTY
A47PCS
47PCS
22PCS
4PCS
50PCS
5PCS 2PCS
25PCS
20PCS
10PCS
10PCS
10PCS
B
C
13
9
PARTS LIST
D
E
F
H
G
I
J
K
L
BOTTOM PANEL
LEFT SIDE PANEL
RIGHT SIDE PANEL
BACK PANEL
DRAWER FRONT
DRAWER LEFT
PANEL
DRAWER FRONT
PANEL
PANEL
PANEL
PANEL
PANEL
DRAWER RIGHT
DRAWER LEFT
PANEL
PANEL
DRAWER RIGHT
DRAWER BACK
PANEL
LEG
LEG
MIDDLE SUPPORT
PANEL
PANEL
DRAWER BACK
DRAWER SUPPORT
DRAWER BOTTOM
NO. ITEM QTY NO. ITEM QTY
11 PC
3
1 PC
41 PC
1 PC
52 PCS
2 PCS
2 PCS
6
1 PC
7
8
15
14
10
12
11
16
18
17
5 PCS
2 PCS
2 PCS
2 PCS
2 PCS
5 PCS
3 PCS
3 PCS
3 PCS
3 PCS
CROSSING BAR
19 1 PC
2
TOP PANEL
(CL) (DL) (DR) (CR)
4x35mm
3x12mm
4x30mm
4x16mm
3x16mm

STEP 1:
STEP 2:
5
2xB 2xC
30xE5xF
2xA
(CL)
(CR)
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
F
F
E
E
E
E
E
E
E
E
E
E
34
E
F
A
A
B
B
C
C
19
4
3

STEP 3:
STEP 4:
6
4xC 4xD
4xA 4xB 4xC
A
A
A
A
B
B
B
B
C
C
C
C
7
7
8
8
C
C
D
D
D
D
2
3
4

STEP 5:
STEP 6:
7
3
4
5
5
6
8xA 8xB 8xC
A
B
B
B
C
2
3
4
7
8
2xA 2xB
A
B
3
4
6

STEP 7:
STEP 8:
8
10xG
6xB6xA 4xC
A
A
A
AA
A
B
B
B
B
B
C
C
1
2
3
4
G
GG
10
11
12
14
9
x2

STEP 9：
STEP 10:
9
15xG
10xB10xA 4xI 8xH8xE2xF
(DL)
(DR)
A
A
A
A
A
B
B
B
E
E
E
E
F
F
H
H
I
I
13
F
F
E
E
x2 x2
x3
G
G
G
17
15
12
14
16

STEP 11:
STEP 12:
10
A
A
A
A
A
B
B
B
H
H
I
I
18
(DL)
(DR)
E
E
E
E
F
F
F
F
E
E
15xB15xA 6xI 12xH
12xE3xF
x3
x3
x3

11
STEP 13:
STEP 14:
13
13
18
18
18
1
2
J
J
K
K
J
J
K
K
J
J
K
K
J
J
K
K
J
J
K
K
10xK10xJ

12
STEP 15:
2xL
L
L
LL
L
L

13
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
HARDWARE
Wall Back side
SCREWS X1 SCREWS X1Anti-tiit Strap X1 Expanded plastic pipe X1 washer X2

To protect your furniture, we suggest the following:
•Avoid placing your furniture in direct sunlight.
•Do not place furniture directly under windows.
•Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
•Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
•Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
14