Kaba Saflok QuantumII MT RFID User manual

QuantumII™MT RFID Installation Instructions
All parts needed to install the QuantumII™ MT™ RFID lock are included with each unit. Please check to make
sure all parts are accounted for before beginning installation. Do not substitute any of the parts. The use of
substitute parts will result in poor performance of the lock.
All information contained herein, including but not limited to product pricing and other intellectual property, is confidential and intended
for the sole use of the addressee(s) so named. Any misuse of this confidential information contained herein may result in legal action by
Computerized Security Systems dba SAFLOK and its parent company.
Proximity Reader Assembly
(A21710-COLOR)
Mortise (see Mortise Options table)
Scalp Plate
(51190-COLOR)
Outside Lever Trim
(A20970-HAND-COLOR)
Screw Pack
(A29070-COLOR)
Strike Plate
(30320-HAND-COLOR)
A70000-Handing
Mortise, 1-3/4
A70020-Handing
Mortsie, 1-3/4
ADB
A70080-Handing
Mortise, 1-3/4
ADB, DAJ2
A70060-Handing
Mortise, 1-3/4
STD, DAJ2
Mortise Options
Inside Trim Assembly
QCLXXXXXX-6--Color

© SAFLOK, all rights reserved. INS_QTMIIMTRFID_2_12
QuantumIITM MT RFID Installation Instructions Pg 2 of 8
Preparing the door and door frame
1. Prepare the door using the QuantumII RFID reader installation template or drill fixture. The door edge prep is a
standard, full-mortise prep for a 1-1/4” x 8” front plate (1” x 8” and 1” x 7-3/4” custom front plates are optional). The
door surface holes and mortise are customized for the SAFLOK trim.
Important: Some holes are only on the inside surface of the door. See the door prep template.
  • Fornewconstructioninstallations,thedoormanufacturermaypreparethedoorusingthe
installation template.
  • Forretrotinstallations,removetheexistinghardwareandconrmthattheexistingdoor
edge prep is appropriate for the SAFLOK mortise lock.
Drill fixture: If you are using a SAFLOK drill fixture, position and clamp the fixture on the door. The fixture has
two positioning posts that rest inside the mortise, establishing the proper backset for the trim. When the fixture
is clamped, its surfaces should be parallel with the door surfaces and door edges. Not all holes go through the
door (refer to the template). Notch the material on the inside surface for easier routing of the motor wire. After
machining, remove any debris from the mortise and cutouts.
2. Prepare the door frame using the template and install the strike plate using the screws provided
(12 x 1-1/2 screws for wood frames, 12-24 x 3/8 screws for metal frames).
Ø
(Always left of lock center
when viewed from outside)
.88 THRU
.30
6.00
0.87
Use only referenced
holes for drilling
QuantumII reader

© SAFLOK, all rights reserved. INS_QTMIIMTRFID_2_12
QuantumIITM MT RFID Installation Instructions Pg 3 of 8
Preparing the door and door frame (continued)
3. The mortise plate has an adjustable bevel. Align the mortise front plate with the bevel of the door edge and tighten
the two bevel adjustment screws at the top and bottom of the mortise case. Position the mortise case in the door
edge with the motor wire routed through the notch (see Fig. 3).
Note: Use care to ensure that the wires do not get pinched or pulled as the mortise is inserted into the pocket.
4. Attach the mortise front plate to the door using the two mortise screws (12 x 1-1/4 screws for wood doors,
12-24 x 3/8 screws for metal doors). Be sure that the screws are fully tightened.
Important: DO NOT leave the screws loose. The screws must be fully tightened before the trim is installed.
If you must leave the mortise loose to install the trim, the door preparation is incorrect.
5. Install the scalp plates with the 8-32 x 1/4 screws provided and test for proper mechanical latch engagement
into the strike plate.
Mortise Front Plate
Fig. 3
Mortise
Screws
Motor
Wire
Notch for routing
the motor wire
(inside only)
Inside Door
Surface

© SAFLOK, all rights reserved. INS_QTMIIMTRFID_2_12
QuantumIITM MT RFID Installation Instructions Pg 4 of 8
Installing the lock trim
The outside lever trim has two carriage bolts that fit into the diagonal holes in the mortise case. These carriage bolts
establish an accurate trim position with respect to the mortise case assembly, allowing the levers and bolt mechanism
to operate without binding. The holes machined in the door surfaces should not influence the position of the trim or the
card reader assembly.
Do not tap or bend the carriage bolts to manipulate the fit of either trim piece during installation. The door prep holes
should accommodate the outside lever trim and the card reader assembly. If the carriage bolts or card reader enclosure
fit too tightly in the door prep holes, remove the mortise and enlarge the holes to achieve a free fit.
1. Remove the battery pack from the inside trim.
2. Position the outside proximity card reader assembly on
the outside of the door (see Fig. 4). Route the ribbon
cable and power cable through the 13/16” hole in
the door. Do not pull on the ribbon cable. DO NOT
CREASE THE RIBBON CONNECTOR
3. Position the inside trim on the inside of the door.
4. Secure inside trim to the proximity card reader
assembly to the inside trim using three
M5 x 31 mm screws.
Important: Do not fully tighten the screws at this point.
5. Align the outside lever trim with the diagonal holes
located on either side of the mortise hub and secure it
using the remaining two 8-32 x 1-1/4 screws (see Fig. 2).
Important: Do not over tighten screws. If using a screw gun,
use a low torque setting.
6. Once the outside lever trim is fully secured, check the alignment of the
inside trim and be sure that the both levers rotate without binding. Once
the trim is properly aligned, fully tighten the screws that secure the proximity
reader assembly to the door and check for proper rotation.
7. Place the battery pack in position above the PCB. Be sure that the battery wire
is routed through the lower left corner of the battery compartment.
Note: Do not plug in the battery until the other connections have been
made at the circuit board.
Proximity Reader
Assembly
Fig. 4
Inside Trim
Outside Lever
Trim
Ribbon Cable
8-32 x 1-1/4
Screws
8-32 x 1-1/4
Screws
Fig. 5
Route the ribbon
connector through the
rectangular hole
Motor Wire
Channels

© SAFLOK, all rights reserved. INS_QTMIIMTRFID_2_12
QuantumIITM MT RFID Installation Instructions Pg 5 of 8
Installing the lock trim (continued)
9. Connect ribbon cable, motor cable, and power wire to the PCB. See Fig. 6. Be sure not to crease ribbon.
10. Watch for the green LED on the card reader to flash four times while you connect the battery wire to the PCB.
The green light indicates that the PCB has reset.
Important: The battery wire should be the last connection made to the PCB.
11. With the dead bolt retracted, insert the long end of the dead bolt spindle assembly through the PCB switch
cam hole and into the mortise dead bolt hub. The indicator marks on the switch cam should be at the right
(3:00 position) when the mortise dead bolt is retracted (see Fig. 6). The retaining ring should rest on the switch
cam when fully inserted (the proper positioning of the cam will allow the door to be opened when the dead bolt
is retracted and block entry when the dead bolt is thrown for privacy, except when emergency keycards are used).
Position dead bolt spindle assembly into cam assembly.
Important: As illustrated in Fig. 3, be sure that the cam is in correct orientation.
12. Install the inside escutcheon with the thumb turn pointed upward.
Fig. 6
Battery Wire
Motor Wire
Battery
Ribbon
Cable
Dead Bolt
Spindle
Position for the ADB mortise
lock assembly
Position for the STD mortise
lock assembly
Route the ribbon over the
battery. Do not crease
ribbon connector.
3:00 Position
ADB Mortise
OR
6:00 Position
Standard Mortise

© SAFLOK, all rights reserved. INS_QTMIIMTRFID_2_12
QuantumIITM MT RFID Installation Instructions Pg 6 of 8
Installing the lock trim (continued)
13. Secure the inside trim cover to the inside trim using two M4 x 16mm Torx screws (see Fig. 7).
14. Program the lock using the Lock Programmer and Interrogator (LPI) probe with the LPI-R device cable. Test the
functioning of the lock as discussed in the following section and in the programming manual before closing the door.
When the construction key is used, the green and red LEDs will blink together, indicating that the lock’s time and
date are not set.
15. For humid outdoor environments, apply dielectric grease inside the USB connector after programming to
guard against corrosion from persistent moisture.
Fig. 7
M4 x 16mm
Torx

© SAFLOK, all rights reserved. INS_QTMIIMTRFID_2_12
QuantumIITM MT RFID Installation Instructions Pg 7 of 8
Testing Lock Functionality
Pass a Construction key over the QuantumII MT RFID reader. The green light will flash for five seconds. Be sure that the
green light flashes for five seconds while the exterior lever remains operable. If the green lights do not flash, refer to
the table below.
Lock Communication Electronic Function Description
Red and green LEDs flash Time and date not set, use the Quantum MT RFID LPI probe to reset
nine times simultaneously
Yellow LED flashes 12 times Dead bolt is thrown or switch cam is not properly aligned
Yellow LED flashes two times Keycard not allowed OR keycard cancelled by new keycard
Red and green LEDs flash Low battery (contact the SAFLOK service department)
alternately nine times
Yellow and red LEDs flash Bad keycard read or corrupted data (may require new
two times simultaneously keycard)

© SAFLOK, all rights reserved. INS_QTMIIMTRFID_2_12
QuantumIITM MT RFID Installation Instructions Pg 8 of 8
SAFLOK Door Unit Inspection Criteria
Appearance
• Finishisfreeofblemishesorscratchesthatwoulddistractfromlockappearance
• Lockbodyandunderplate(ifused)aremountedstraightonthedoor
• Doorscalpismountedstraightandushwiththedooredge
• Jambstrikeismountedstraightandisushwiththejambface
• Correctionofminorblemishesonthedoorjambaretheresponsibilityoftheproperty’smaintenancedepartment
Lock Function
• Knoborleverrotatesandmovesfreely
• Leverishorizontaltooorwhenatrestposition
• Deadboltextendsfullyandretractswithoutbinding(dooropen)
• Locklatchanddeadboltengagejambstrikeplatefreely
• Anti-picklatchwhendepressed(dooropen)
• Anti-picklatchisdepressedwhencontactismadewiththestrikeplate(doorclosed)
Electronics/Keycards
• Presentkeycardinfrontofreader,andtheyellowlightashestwicewhenincorrectkeycardisused
• Greenlightasheswhentheproperkeycardisused
• Greenlightisashingwhentheleverisoperated
• Greenlightcontinuestoashforave-secondcycle
• Yellowlightashes12timeswhenthedeadboltisextendedandaguest/hotelkeycardisused
• Allkeycardsfunctiontothespecicationsofthepropertieskeydesign
Door function
• Doorclosesandlatcheswithlittleornointerference
• Deadboltextendsfullythroughthestrikeplatewithoutinterference(doorclosed)
• Spacingbetweendooredgeandinsidedoorjambdoesnotexceed3/16”(doorclosed)
Note: If bumpers or other seals are added after strike plate installation and causes alignment and latch problems,
it is the property’s responsibility to correct this condition. This note generally applies to new construction or new
door installation.
FCC and IC Warnings: This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
© SAFLOK, all rights reserved. INS_QTMIIMTRFID_2_12