Kamoer UIP CK15 User manual

UIP WIFI smart peristaltic pump
User Manual
Version：A/0
Kamoer fluid tech(Shanghai)Co., Ltd.
www.kamoer.com
www.ecounit.kz
инструкция по эксплуатации

Catalog
CATALOG............................................................................................................................................ 2
QUALITY GUARANTEE............................................................................................................................. 3
NOTICE................................................................................................................................................ 0
PRODUCT INFORMATION............................................................................................................... 1
1.1ABOUT................................................................................................................................................. 1
1.2 CASE-OPENING .................................................................................................................................... 3
2．RUNNING OPERATION ............................................................................................................... 3
2.1 CONTINUOUS MODE............................................................................................................................. 4
2.2.1 Continuous mode setting ............................................................................................................. 5
2.2.2 Continuous mode level detection setting ..................................................................................... 6
2.2 RATION MODE...................................................................................................................................... 7
2.2.1 Ration mode setting ..................................................................................................................... 8
2.2.2 Ration mode level detection setting ............................................................................................. 9
2.2.3 Ration mode copy volume.......................................................................................................... 10
2.3 SYSTEM SETTINGS ............................................................................................................................. 12
2.4 TUBULAR CALIBRATION..................................................................................................................... 12
2.5 WI-FI REMOTE CONTROL ................................................................................................................... 14
2.6 485 REMOTE CONTROL....................................................................................................................... 14
2.7 CAN REMOTE CONTROL .................................................................................................................... 14
3．APP RUNNING OPERATION ..................................................................................................... 14
3.1 DOWNLOAD KAMOER PUMPS APP ..................................................................................................... 14
3.2 RATION NETWORK ............................................................................................................................. 15
3.3APP MODULE INTRODUCTION............................................................................................................. 21
3.4 CONTINUOUS MODE........................................................................................................................... 21
3.4.1 Continuous mode liquid level detection..................................................................................... 23
3.5 RATION MODE.................................................................................................................................... 23
3.5.1 Ration mode setting ................................................................................................................... 25
3.5.2 Ration mode level detection....................................................................................................... 25
3.5.2 Ration mode copy function ........................................................................................................ 26
3.6 SYSTEM SETTINGS ............................................................................................................................. 27
3.6.1 Tubular calibration.................................................................................................................... 27
4．MAINTENANCE.......................................................................................................................... 28
4.1 CHEMICAL COMPATIBILITY................................................................................................................ 28
4.2 STORAGE ........................................................................................................................................... 29
5.TECHNICAL SUPPORT................................................................................................................. 29
APPENDIX......................................................................................................................................... 29
APPENDIX APARAMETERS ...................................................................................................................... 29
APPENDIX BPACKING LIST...................................................................................................................... 30

Quality guarantee
1.Warranty conditions
Free service is limited to the warrantyperiod under normal use and maintenance of the
user's manual is valid, all due to malfunction or damage not covered under warranty.
Users please take care of purchase invoices, user manual, so you can receive timely
and satisfactory after-sales service.
2.Warranty coverage
Within One year from the date of purchase, if any resulting from the manufacturing
process or component damage occurred, the free warranty service will be provided.
The free repair service provided during the warranty period includes free repair, free
replacement and replacement of faulty spare parts, and products that cannot be repaired
are replaced by the same model (if the model has been discontinued, the model is similar).
The free service does not include shipping costs for the product due to repairs.
3.Non-warranty coverage
The following factors is not within the scope of free warranty, customer service
should pay the costs.
1) Appearance of the product (Please confirm it at the time of purchase).
2) Improper use, maintenance, or storage (according to the user manual on the proper
use, maintenance and storage).
3) Access improper power supply.
4) (Such as insects, etc) into the machine and circuit board components caused by the
short circuit caused by damage.
5) Losses due to accidents.
6) Use of inappropriate parts (the company spare parts do notapply).
7) Non-authorization of the company's negligent handling, modification, or repair
(please do not attempt to disassemble to repair).
8) Application failures or damage caused by use outside.
9) Damage due to force majeure.
10) Consumable spare parts (such as silicone hose, tubing,etc).
11) The warranty expired

Notice
We have considered the safety of the user in the process of design of the
instrument. Please read the manual carefully for installing and use of the
instrument. Any improper operation may cause damage or danger.
1.Safety
The product belongs to Active Products. The Operator should follow the
regulation rules to avoiddanger.
 If you find any visible damage, please do not switch on.
 Be sure not to use in humid environment, avoid damage by shortcircuit.
 Temperature changes or mechanical wear may cause the increases in the
dispensed volume.
2.Defect and anomalous situation
You must stop any operation immediately if the equipment is damaged. The
equipment may be damaged when the following situation occurs:
 There is visual damage.
 The product suddenly does not work.
 The product is located in an inappropriate position.

Kamoer fluid tech(Shanghai)Co., Ltd. UIP WIFI User Manual
1
Product Information
1.1 About
UIP series peristaltic pump is using stepping motor control, commonly used in low
traffic and high precision setting, configure the touch screen 480 x 272, powerful,
easy to operate. Product appearance as shown in Figure 1-1.
Figure 1-1 Exterior look

Kamoer fluid tech(Shanghai)Co., Ltd. UIP WIFI User Manual
2
Figure 1-2 Port look
Each interface definition:
1. Fan:A machine fan used to remove heat from the machine during operation;
2. Liquid level sensor interface: used to connect the liquid level sensor expansion
component, so that the instrument has the function of liquid level detection;
3. Temperature sensor interface: used to plug the temperature sensor expansion component,
so that the instrument has the function of temperature detection;
4: CAN communication interface: connect RJ45 connector CAN communication line, can
remotely control the machine through CAN;
5.RS485 communication interface: connect RJ45 connector RS485 communication line,
remotely control the machine through RS485;
6. Wi-Fi antenna: 2.4G Wi-Fi antenna, which can be controlled by mobile app;
7. Integrated switch: switch and power line interface;
8, 9. Expansion interface: used to connect with expansion devices, such as foot switch, PC,
PLC and other equipment, two ports can be inserted at will. However, to ensure availability, please
use utrao's standard harness.
! ! Note that the use of non-utrao standard harnesses may result in damage to the
instrument and the damage is not covered by the warranty.

Kamoer fluid tech(Shanghai)Co., Ltd. UIP WIFI User Manual
3
1.2 Case-opening
 Open the package before packing, check if the packaging is damaged in the
shipping process.
 After you open the package, refer to the packing list in theAppendix, and
verify that all components without fail, check for visibledamage.
2．Running operation
After the boot, the four title bars of the main interface are introduced:
Figure 2-1 Boot interface
1. Continuous mode: applied to the scene where the pump continues to run for a long time.
After the start, the pump will run all the time, click the pump again to stop the operation; the
flow rate can be adjusted during the pump operation;
2. Distribution mode: suitable for filling occasions, the pump runs a certain amount, then
automatically stops, the user can manually trigger the start, or set the number of cycles to let the
pump run cyclically;
3. System settings: set the system to include the tube type settings, Wi-Fi settings, language
settings, time settings, system information, system self-test, factory reset, screen calibration and

Kamoer fluid tech(Shanghai)Co., Ltd. UIP WIFI User Manual
4
other functions;
4. Control mode: including remote control functions such as Wi-Fi, RS485, CAN;
2.1 Continuous mode
After booting up, select “Continuous Mode” in the navigation bar to enter the continuous
mode control interface; in continuous mode, after clicking Start, the pump will run continuously
until the stop button is clicked;
Figure 2-2-1 Continuous mode interface
a, Continuous mode: continuous mode title;
b. Tube type: continuous mode tube type setting, tube type record has corresponding flow rate
information, the same speed will use different tube type flow rate will be different;
c. Speed: the current set speed of the continuous mode, the speed cannot be directly set, and the
speed is converted according to the current flow rate setting;
d, Temperature: display the temperature of the external temperature sensor, when the external
sensor is not connected, it is displayed here;
e, Flow rate display: display the current set flow rate, can be modified by the on-screen keyboard
or flow rate plus / minus buttons;
f. Acceleration/deceleration button: Click this button to increase or decrease the flow rate. The
amount of increase or decrease each time is the amount of change indicated in i; the button
operates when the motor is running and stopped;
g、Set button: Click to enter the continuous mode setting interface. For details, see 2.2.1
Continuous mode setting;
h, direction button: click to switch the direction of rotation of the pump, set when the pump stops
running, can not operate when the pump is running;
i, acceleration and deceleration granularity: used to modify the speed of the click
acceleration/deceleration button change, there are several sizes of 0.1, 1, 5, 10;

Kamoer fluid tech(Shanghai)Co., Ltd. UIP WIFI User Manual
5
j. Runn Volume (ml): The volume in which the continuous mode has been run. When the pump is
running, the run volume continues to increase. When the continuous mode is restarted, the run
volume increases from 0;
k, Start/Stop button: continuous mode start stop button;
l, Wi-Fi status display: Here shows the status of Wi-Fi, the specific Wi-Fi status refers to 3.2
ration network chapter;
2.2.1 Continuous mode setting
In the continuous mode, click the "Settings" button in the lower left corner to enter the continuous
mode setting interface:
Figure 2-2-1-1 Continuous mode setting interface
a. Tube type setting: Click to enter the tube type selection interface and select the corresponding
tube type. Each tube type has a corresponding relationship between the speed and the flow rate. If
not, the tube type can be performed in the system setting->tube type. calibration;
b. Liquid level detection: Click the liquid level detection to enter the liquid level detection setting
interface, set the liquid level detection on and off in the liquid level detection setting interface, the
type of alarm; if the liquid level detection is on, when the pump works, if When the liquid level
alarm is detected, the pump stops working and an alarm is given;
c. Foot switch: Click to switch the opening and closing of the foot switch control. If the foot
switch is turned on, the continuous mode can be controlled to start and stop by the foot switch;

Kamoer fluid tech(Shanghai)Co., Ltd. UIP WIFI User Manual
6
Figure 2-2-1-2 Continuous Work Tube Setting Interface
2.2.2 Continuous mode level detection setting
If the liquid level detection is on, when the pump is working, if the liquid level alarm is
detected, the pump stops working and an alarm prompt is given; in continuous mode, click
Set->Level Detection to enter the continuous mode level detection setting. interface:
Figure 2-2-2-1 Continuous mode liquid level detection setting
a. Detection switch: open and close the liquid level detection;
b. Alarm type: The liquid level float has two states of floating and sinking. The state of floating
and sinking of different liquid level floats is different. Here, choose which state the float is used as
an alarm.

Kamoer fluid tech(Shanghai)Co., Ltd. UIP WIFI User Manual
7
2.2 Ration mode
After the power is turned on, clicking the Ration mode in the title bar will enter the ration
mode work interface; in the ration mode, there are two working modes, namely the fully automatic
working mode and the semi-automatic working mode;
1. Semi-automatic working mode: Click h working volume display area to set the volume.
After determining the quantity, click the start button to start running, the flow rate starts to count
in the middle of the screen. When the counting value and the setting amount are equal, the pump
stops working, click again to start. , the pump is again operated in the above manner;
2, fully automatic working mode: set the number of cycles, set the working volume, pause
time, click to start running, the middle of the screen shows the flow starts counting, when the
count value and the set quantitative are equal, the pump stops running, and the middle of the
screen begins to The pause time countdown, when the countdown is 0, the pump automatically
restarts the work, the pump runs once and records it as a cycle. When the cycle is set a number of
times, the pump stops running, waiting for the click to start, and starts the next cycle;
Figure 2-2-1 Assignment mode
a, Ration mode: allocation mode title;
b. Tube type: the ration mode tube type setting, the tube type record has the corresponding flow
rate information, and the same speed will use different tube type flow rates;
c, Flow rate: the current flow rate setting of the ration mode;
d, Speed: the current set speed of the ration mode, the speed can not be directly set, the speed is
converted according to the current flow rate setting;
e, Temperature: shows the temperature of the external temperature sensor, when the external
sensor is not connected, it is displayed here;
f, Working volume display: display the currently set working volume;
g, Copy function entry: When you do not know how much volume you need to add, you can use

Kamoer fluid tech(Shanghai)Co., Ltd. UIP WIFI User Manual
8
this function to copy a volume first;
h, working volume: display the working volume, when the ration mode starts working, the value
decreases with the work of the pump, indicating the working process;
i. Pause time: the interval between each filling in the automatic mode of the ration mode;
j. Cycle mode and progress display: The ration mode has two modes: full-automatic and
semi-automatic. When working in semi-automatic mode, the number represents the number of
times of work. When working in the fully automatic mode, the number format is the number of
times of work. / target work times;
k. Settings: Click to enter the ration mode setting interface. For details, see 2.2.1 Ration Mode
Settings.
l, Direction button: click to switch the direction of rotation of the pump, set when the pump stops
running, can not operate when the pump is running;
m, Pause time: Click to set the allocation mode pause time, the unit is second;
n, The number of cycles: click the number of cycles to set the automatic mode of the ration
mode;
o, Start/Stop button: assign mode start stop button; in semi-automatic mode, when the set
working volume finishes running, the ration mode stops automatically. In the fully automatic
mode, when the cycle number runs out, the ration mode stops automatically;
p, Wi-Fi status display: Here shows the status of Wi-Fi, the specific Wi-Fi status refers to 3.2
ration network chapter;
2.2.1 Ration mode setting
In the ration mode, click the "Settings" button in the lower left corner to enter the ration
mode setting interface:
Figure 2-2-1-1 Assignment Mode Settings
a. Tube type setting: Click to enter the tube type selection interface and select the corresponding

Kamoer fluid tech(Shanghai)Co., Ltd. UIP WIFI User Manual
9
tube type. Each tube type has a corresponding relationship between the speed and the flow rate. If
not, the tube type can be performed in the system setting->tube type. calibration;
b, Flow rate setting: click to set the flow rate of the ration mode;
c. Liquid level detection: Click the liquid level detection to enter the liquid level detection setting
interface, set the liquid level detection on and off in the liquid level detection setting interface, the
type of alarm; if the liquid level detection is on, when the pump works, if When the liquid level
alarm is detected, the pump stops working and an alarm is given;
d. Foot switch: Click to switch the opening and closing of the foot switch control. If the foot
switch is turned on, the continuous mode can be controlled to start and stop by the foot switch;
e, fully automatic cycle / semi-automatic cycle: click to switch automatic mode and
semi-automatic mode;
f, Number of clearing: Click to clear the number of times of automatic cycle and semi-automatic
cycle;
Figure 2-2-1-2Allocation mode tube type selection
2.2.2 Ration mode level detection setting
If the liquid level detection is on, when the pump is working, if the liquid level alarm is
detected, the pump stops working and an alarm prompt is given; in the dispensing mode, click
Settings -> Level Detection to enter the dispense mode level detection setting. interface:

Kamoer fluid tech(Shanghai)Co., Ltd. UIP WIFI User Manual
10
Figure 2-2-2-1Assignment mode level detection setting
a, Detection switch: open and close the liquid level detection;
b. Alarm type: The liquid level float has two states of floating and sinking. The state of floating
and sinking of different liquid level floats is different. Here, choose which state the float is used as
an alarm
2.2.3 Ration mode copy volume
The copy volume is used when the working volume that is running in the ration mode is
unknown. The principle is to fill the container to be filled, how much time (volume) is needed,
and then use this time to control the pump operation for filling;
Note: Empty the air in the pump tubing before copying.

Kamoer fluid tech(Shanghai)Co., Ltd. UIP WIFI User Manual
11
图2-2-3-1 分配模式复制体积
Figure 2-2-3-1Assign mode copy volume
a, Tube type: the mode of the ration mode, set in the ration mode;
b, Flow rate: ration mode flow rate, set in the ration mode;
c, Speed: ration mode speed, according to the ration mode flow rate setting conversion;
d, Run volume: the real-time volume after the start of replication;
e. Prime: Before starting to copy, you need to empty the air in the pump tube. Click the empty
button to start the motor, empty the pump tube air, click the empty button again, and the pump
stops running.
f, Start/Stop: Click to start copying, click again to stop copying;

Kamoer fluid tech(Shanghai)Co., Ltd. UIP WIFI User Manual
12
2.3 System settings
Figure 2-3-1 System Settings
a. Tube type setting: tube type setting is used to calibrate different pump tubes;
b. Wi-Fi setting: Click to set the Wi-Fi connection mode, which is divided into AP mode and
router mode. The AP mode is for the mobile phone to directly connect to the machine for control.
The router mode mobile phone and the machine are connected to the router, and the mobile phone
controls the machine through the router.
c. Language setting: switch the language displayed by the machine, support Chinese and English;
d. Time setting: click to set the real-time clock of the machine;
e. System information: click to enter the display system information, including firmware version,
model number, serial number;
f. System self-test: check whether the functions of the system are normal;
g. Restore factory settings: click to restore the factory settings, after restoring the factory settings,
all parameters will be restored to the factory defaults;
h. Screen calibration: Click to enter the screen calibration interface. In the screen calibration
interface, click the cross on the screen to complete the screen calibration.
2.4 Tubular calibration
When the accuracy of the pump is found to be reduced, the pump needs to be calibrated.
In the system setting interface, click the tube type setting -> select the tube type to be calibrated in
the pop-up tube type -> enter the tube type calibration interface:

Kamoer fluid tech(Shanghai)Co., Ltd. UIP WIFI User Manual
13
Figure 2-4-1 System Settings
a. Tube type: the current calibrated tube model;
b. Flow rate: the flow rate before calibration;
c. Speed: the speed corresponding to the current flow rate;
d. Calibration progress: starting from 0, when the calibration is completed, it is 100;
e. Calibration time: the length of time the calibration needs to be run, and the longer the
calibration time setting will make the calibration more accurate if the calibration container allows
it;
f. Calibration time: click to set the calibration time;
g. Flow rate setting: click to set the calibration flow rate, change the flow rate will change the
corresponding speed;
h. Prime: Click to start priming, click again to stop emptying, when calibrating, you need to
empty the air inside the pump tube;
i. Start/Stop: click start, the pump starts running, the calibration progress will show the progress.
When the calibration time countdown is completed, the pump stops running, the interface will pop
up the input box, and the volume obtained by the pump operation needs to be input to complete
the calibration;
Calibration process and areas to be aware of:
1. Preparation before calibration: Connect the pump tube outlet into the measuring cylinder, put
the water inlet into the water container, and fix the pump tube outlet and water inlet to prevent
the pump tube from sprinkling water when the pump works. Operation console
2. Enter the calibration function: in the system settings -> tube type settings -> select the tube
type that needs to be calibrated to enter the tube type calibration interface;
3. Set the calibration time: set the time as long as the cylinder allows, so that the accuracy of the
pump will be higher after calibration;
4. Flow rate setting: set a flow rate that needs to work;
5. Drain the pump tube: Click the empty button to let the water fill the pump tube and empty the

Kamoer fluid tech(Shanghai)Co., Ltd. UIP WIFI User Manual
14
air in the pump tube. If the pump tube is drained, there is water in the cylinder, and the water in
the cylinder should be drained to ensure that the cylinder is empty;
6. Start calibration: Click the start button, the pump starts running, the calibration starts, there
will be a countdown and calibration progress on the screen;
7. Enter the volume obtained by calibration: When the progress on the screen is 100%, the
calibration is completed, the keyboard will pop up on the screen, input the volume of water in
the measuring cylinder in the winch, and click OK to complete the calibration;
2.5 Wi-Fi remote control
Refer to the third chapterAPP operation
2.6 485 remote control
UIP includes 485 remote control function. For details, please refer to the UIP 485 remote control
protocol.
2.7 CAN remote control
The UIP includes the CAN remote control function. For the specific operation method, please
refer to the UIP CAN operation remote protocol.
3．APP running operation
3.1 Download Kamoer PumpsApp
1.Scan the QR code and download the app corresponding to the icon below.
iOS Android
1.Apple users enter the App Store app store, Android users enter the Google Play, search for
"kamoer pumps", find the app download of the corresponding icon.
Kamoer Pumps App supportsAndroid 4.4 and above, and supports iOS 9.1 and above.

Kamoer fluid tech(Shanghai)Co., Ltd. UIP WIFI User Manual
15
3.2 Ration network
This unit includes Wi-Fi, which can be controlled by the Kamoer Pumps App via Android or iOS
phones.
Before using Wi-Fi, make sure the Wi-Fi antenna on your machine is properly installed and turn
on the Wi-Fi function on your machine:
Figure 3-2-1 Wi-Fi switch settings
There are two ways to control Wi-Fi:
Connection
mode
Description
Advantages
Disadvantages
Direct mode
（AP）
Factory default mode, you can see the
dosing pump Wi-Fi in the Wi-Fi list of
the mobile phone (the name starts with
KAMOER, followed by the 5-digit
serial number, the connection password
is a12345678), and the user directly
connects to the Wi-Fi control
Dosing pump Simple
connection
Only one
pump can be
controlled at a
time
Router
mode (STA)
Cannot see the dosing pump Wi-Fi in
the mobile Wi-Fi list, the user controls
the dosing pump by connecting the
wireless router.
After the
configuration is
successful, multiple
pumps can be
controlled by the
router
to support the
2.4G router,
and the 5G
router is not
supported.
The screen title bar shows the Wi-Fi connection method and connection status:
Indicates the AP direct connection mode;

Kamoer fluid tech(Shanghai)Co., Ltd. UIP WIFI User Manual
16
Indicates the STA router mode;
Indicates the STA router mode, but the machine is not connected to the router;
Indicates that the machine is waiting for the ration network status in Wi-Fi. At this time,
the user can configure the machine to connect to the router on the mobile terminal and enter the
STA router mode.
1. Direct connection mode connection pump
Step 1: Power on and click on the title bar to enter the system settings interface;
Step 2: Click Wi-Fi Settings to enter the connection mode selection interface;
Step 3: Select Wi-Fi reset in the pop-up connection dialog box;
Step 4: Select the OK button in the confirmation dialog box that pops up to reset the Wi-Fi to AP
Direct mode;
Step 5: After completing the Wi-Fi reset, the pump enters the AP Direct mode and the title bar
icon changes to
Step 6: The mobile phone searches for the Wi-Fi connection of KAMOER-UIP-XXXXX, and the
connection password is a12345678;
Step 7: Open the Kamoer Pumps App search device for control;