Kamoer X1 PRO 2 User manual

Quick Start Guide
X1 PRO 2
Dosing Pump
A3 2022/03/14
Kamoer Fluid Tech (Shanghai) Co., Ltd.
www.kamoer.com

2
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation
This device has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This device generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this device does cause harmful interference to radio or television reception, which can be
determined by turning the device off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the device and receiver.
--Connect the device into an outlet on a circuit different from that to which the receiver is
connected.
--Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment
FCC Radiation Exposure Statement The antennas used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not be
colocated for operating in conjunction with any other antenna or transmitter.

3
Warranty service
1. Warranty Conditions
The warranty service is only valid for users who have correctly installed, used and maintained
in accordance with the manual, and all man-made faults or damages are not covered by the
warranty. Please keep the proof of purchase in a safe place so that you can obtain satisfactory
after-sales service in a timely manner.
2. Warranty coverage
Within one year from the date of purchase, if there is any damage caused by the manufacturing
process or components, the company will provide free warranty service. The free maintenance
service provided during the warranty period includes free repair, free replacement of faulty
spare parts, and replacement of products that cannot be repaired with products of the same
model. Free service does not include shipping costs incurred for product repairs.
3. Non-warranty coverage
The following factors are not covered by the free warranty, and customer repairs are subject to
fees.
1) Product appearance (please confirm when purchasing);
2) Improper use, maintenance, or storage (please use, maintain and store correctly according
to the user manual);
3) Access to inappropriate power supply;
4) Damage to the components caused by the short circuit of the circuit board caused by the
entry of various insects into the machine;
5) Losses caused by accidents;
6) Use inappropriate spare parts (non-company spare parts are not applicable);
7) Persons not authorized by the company negligently handle, modify or repair (please do not
dismantle or repair without authorization);
8) Failure or damage caused by use outside the applicable occasion;
9) Damage caused by force majeure, etc.;
10) Consumable and wearing parts (pump tube, connector, connecting tube, etc.);
11) The warranty period has expired.

4
Know X1 PRO 2
X1 PRO 2 is a single-channel intelligent dosing pump with WIFI remote function, mainly
used to add the various elements needed for marine life growth, such as calcium,
magnesium, KH booster, trace elements, etc. to marine life cylinder timing, quantitative
and accurate. The automation of X1 PRO 2 can greatly reduce the amount of manual
added work, but also avoid manual addition caused by leakage, adding excessive or
insufficient errors.

5
Download app
1. Scan the QR code on packing box or below, download the app of the icon below.
2. Apple users enter the App Store, Android users enter the Google Play, search for
"Kamoer Remote" and find the corresponding icon app download.
Note: This app supports iOS 9.1 and above versions of Apple devices, Android 4.4 and
above versions of Android devices.
Register account
Open the App, scan the QR code of the device or manually select the region where the device is
located, register via mobile phone or email, and follow the App prompts to complete the
account registration.
Note: Region selection is very important. Wrong region selection will result in failure to
configure the network. It is recommended to scan the QR code of the device to select the
region.

6
View Tutorial
On the device list page, click the "?" icon in the upper right corner to enter the "Tutorial" page,
and select "X1 PRO 2 " to view the tutorial. The tutorial includes the user manual and
frequently asked questions.
Indicator light
Indicator Status Description
Status Indicator
（blue）
On Connected to the cloud
Off Disconnected from router
Flashes quickly Configure network by router
Slow flashing (on for 0.2 seconds
and off for 2 seconds) Configure network by AP
Slow flashing (on for 2 seconds
and off for 2 seconds) Disconnected from the cloud
Power Indicator
（red）
On Powered on
Off No power supply or power failure
Note: Devices of version 1.1.04 and above support AP network configuration. For devices
below version 1.1.04, please upgrade the firmware to the latest version.

7
Connect X1 PRO 2 to the cloud
The dosing pump is powered on for the first time after unpacking, and the status indicator light
(blue) flashes slowly. You then need to use the App to connect the micropump to the cloud
through a wireless router. The steps are as follows:
1. Ensure that the wireless router has connected to the Internet. The mobile phone is
connected to the 2.4G Wi-Fi hotspot of the wireless router (the device does not support 5G
Wi-Fi, and 5G Wi-Fi hotspots cannot be used)
2. Open the Kamoer Remote App, log in with the registered account, click the "+" icon in the
upper right corner, select "Add Device", select "X1 PRO 2 Dosing Pump" in the list of
supported devices to add.
3. After entering the router Wi-Fi password, click the "Next" button, press and hold the Reset
button on the front panel for more than 6 seconds, then release it, click the "Next" button,
and wait for the blue status indicator to flash;
4. If the indicator light continues to flash rapidly (configure network by router), select the
"The blue light is flashing fast and continuously" icon on the App interface, click the
"Next" button, and wait for the network configuration to be completed.
5. If the indicator is flashing slowly at a frequency of on for 0.2 seconds and off 2
seconds(configure network by AP), select the "The blue light is flashing slowly and
intermittently" icon on the App interface, click the "Next" button, and complete the
network configuration according to the interface prompts.
6. After the connection is successful, the App will prompt that the connection is successful. At
this time, the status indicator (blue light) is on, indicating that micropump has been
connected to the cloud, and the user has also completed the binding with micropump.
Binding X1 PRO 2
There are two ways for user to bind the X1 PRO 2.
Method 1: Bind the dosing pump through the network configuration described above.
Method 2: If the dosing pump is connected to the cloud through the router, the mobile phone
can be connected to the wireless router, and the App will scan and display the locally available
dosing pump. The user directly clicks the "Bind" button on the right side of the dosing pump to
complete the binding.

8
Unbind
On the device list page, press and hold the corresponding dosing pump icon, the "Remove"
icon pops up at the bottom, and clicks the Remove icon to unbind.
Notes
Please use the product's own power adapter and work in the specified working
environment.
This product only supports 2.4G WIFI and does not support 5G WIFI.
The dosing pump should be placed in a reasonable position to ensure that the
height difference between the inlet and the outlet is within 0.5 m.
The connection pipe for liquid inlet should be as short as possible, and the outlet
connection pipe should be suspended above the container.
Please check carefully that the inlet and outlet connections are in the correct
direction.

9
Technical parameter
Dimensions
(length * width * height) 60 * 95 * 83 mm (including pump head)
Weight 214g (does not include power adapter)
Power Adapter Input: 100VAC -240VAC
Output: DC12V 1A
Dosing
parameters
Dosing channel: 1 KXF-B06 pump head
Flow: >33ml/min
Number of dosing：24 times/day - 1 time/99 days
Dosing accuracy：<±2%
Volume range：0.1ml-9999ml
Interface Wi-Fi
Working environment Temperatures: 0 - 70℃
Humidity: 10% - 90% (non-condensation)
Storage environment Temperature: -20C - 85℃
Humidity: 10% - 90% (non-condensation)

10
Packing list
No Name Model Unit Qty
1 Dosing pump X1 PRO 2 pcs 1
2 Power adapter body DC12V 1A pcs 1
3 Power adapter plug □US □UK □EU □AU pcs 1
4 Plastic cylinder 10ml pcs 1
5 PVC connection tube 3*5 mm; Transparent meter 2
6 Power extension cable L-type;75mm pcs 1
7 Quick start guide English pcs 1
8 Hanging screw ST2.9*13 pcs 2

Kamoer Fluid Tech (Shanghai) Co., Ltd.
Addr: Building 4, No.79 Xiangjing Road, Songjiang District, Shanghai
Website：www.kamoer.com
Kamoer is registered trademark of Kamoer Fluid Tech (Shanghai) Co., Ltd. We reserve the right
to improve or alter appearance and technical specifications without notice.