Kargo Master 4A97L-Rev 1 Manual

Instruction Guide
4A97L-Rev 1
Kargo Master
Rancho Cordova, CA 95742
800-343-7486
[e-mail]
DATE: ______________

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 1
Instructions –4A97L
*PLEASE READ ALL INSTRUCTIONS AND WARNINGS PRIOR TO ASSEMBLING,
INSTALLING, AND USING THIS PRODUCT*
Warning
Always check for wires, fuel tanks and lines, brake lines and other important vehicle
functionality items prior to drilling and installing all products.
Tools Needed
13mm Socket and Wrench
10mm Socket and Wrench
4mm Allen Hex
9/16” Socket and Wrench
1/2” Socket and Wrench
7/16” Socket and Wrench
Table of Contents
Parts List ................................................................................................................................ 2-3
Hardware .............................................................................................................................. 4-5
Roof Rail Mounting
Promaster City ....................................................................................................................... 6
NV200/City Express ............................................................................................................... 7
Transit Connect ..................................................................................................................... 8
Rack Assembly
Step 1 –Assembly of Foot ..................................................................................................... 9
Step 2 –Determine Bows and Mount Pan Hooks ............................................................... 10
Step 3 –Mount to Rails ....................................................................................................... 11
Step 4 –Install Torque Tube ................................................................................................ 12
Step 5 –Install End Tube ..................................................................................................... 13
Step 6 –Install Latch ............................................................................................................ 14
Step 7 –Install Handle ......................................................................................................... 14
Step 8 –Ladder Stop ............................................................................................................ 15
Step 9 –Assemble Ladder Hook .......................................................................................... 16
Step 10 –Install Ladder Hook .............................................................................................. 17
Before You Begin
•Read all instructions. Find your vehicle roof rail mounting prior to rack assembly.
•Be sure to put sealant around all threads entering cargo area and between the rubber
spacer and roof of vehicle to prevent water from leaking into cargo area.
**DO NOT EXCEED MANUFACTURERS WEIGHT CAPACITY FOR ROOF**

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 2
Instructions –4A97L
Parts

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 3
Instructions –4A97L
Parts Con’t

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 4
Instructions –4A97L
Hardware (1 of 2)

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 5
Instructions –4A97L
Hardware (2 of 2)

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 6
Instructions –4A97L
DO NOT EXCEED MANUFACTURERS WEIGHT CAPACITY FOR ROOF
Promaster City Installation
•Locate 6 mounting locations
shown on roof of van.
•Install “Top Rail” as shown using
M6x20mm bolts with lock
washers and flat washers.
•In most installs, the rail upright is
to the outside of the van.
•Be sure to put rubber washer between the “Top Rail” and the roof to ensure sealing.
•Place sealant on and around threads to seal roof. (Passenger side shown)
Front EXP
Mid EXP
Rear EXP
Front Tighten
Mid Tighten
Rear Tighten

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 7
Instructions –4A97L
DO NOT EXCEED MANUFACTURERS WEIGHT CAPACITY FOR ROOF
NV200/City Express Installation
•Locate 4 mounting locations shown
on roof of van.
•Install “Top Rail” as shown using
M8x30mm bolts with lock washers
and flat washers.
•In most installs, the rail upright is to
the outside of the van.
•Mount rail so there is about 1” from the rear door opening.
•Be sure to put rubber washer between the “Top Rail” and the roof to ensure sealing.
•Place sealant on and around threads to seal roof. (Passenger side shown)
Front EXP
Rear EXP
Front Tighten
Rear Tighten

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 8
Instructions –4A97L
DO NOT EXCEED MANUFACTURERS WEIGHT CAPACITY FOR ROOF
Transit Connect Installation
•Locate 4 mounting locations shown
on roof of van.
•Be sure to put rubber washer
between the “Top Rail” and the roof
to ensure sealing.
•In most installs, the rail upright is to
the outside of the van.
•Mount rail so there is about 1” from the rear door opening.
•Install “Top Rail” as shown using M8x25mm bolts and flat washers on the outside. Use the
fender washer and nyloc nut on the inside of the van.
•Place sealant on and around threads to seal roof. (Passenger side shown)
Front EXP
Rear EXP
Front Tighten
Rear Tighten

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 9
Instructions –4A97L
Assembly Instructions
Step 1 –Assembly of Foot
•Measure width between previously installed rails.
•On the cross bows, use the slots that correspond to the measured distance between rails.
•Bolt feet to bows as shown, DO NOT TIGHTEN at this point.
•Feet can be installed as shown or reverse depending on how you mounted the rail.
•Most common orientation is with the opening in the foot toward the center of the van
•Use a 3/8”x 1" hex head bolt, 3/8”lock washers and a 3/8”flat washer to bolt foot to
crossmember. Snug Tighten, but allow movement.
Driver Side Shown Below.
On Passenger Side, Rotate pan out of the way to access mounting slots.

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 10
Instructions –4A97L
Step 2 –Determine Bows and Mount Pan Hooks
•Bolt pan hooks to
the exposed end of
each bow.
•Use a 5/16”
carriage bolts,
5/16”washers and
a 5/16”nyloc nuts.
•TIGHTEN. Skip if
adding a rack onto
the driverside.
Determine front and rear bow. The rear bow will have a dampening mechanism attached.
Front Bow
Rear Bow

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 11
Instructions –4A97L
Step 3 –Mount to Rails
•Place both bows on top of installed rails.
•Be sure to place the front bow at the front of the vehicle.
•Bolt feet to rails using 5/16”x 1”carriage bolts, 5/16”flat washers and 5/16”nyloc nuts.
•Put the ladder hooks on the driver side of vehicle.
Snug Tighten, but allow movement.
*Driver Side Shown*

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 12
Instructions –4A97L
Step 4 –Install Torque Tube
•Install torque tube to front pan assembly using 1/4" x 1” hex heads, 1/4" flat washers and 1/4"
nyloc nuts.
*Front bow shown*
*Rear bow shown below*
TIGHTEN all 6 bolts.

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 13
Instructions –4A97L
Step 5 –Install End Tube
•Install end tube to the end of each bows pan assembly using 3/8" x 3/4” hex heads, 3/8” lock
washers and 3/8” flat washers.
TIGHTEN
*Front bow shown below*

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 14
Instructions –4A97L
Step 6 –Install Latch
•Move rear pan assembly out of the way
to expose the end of the crossmember.
•Bolt through the middle set of square
holes as shown.
•Bolt latch assembly to end of
crossmember using 5/16” x 1" carriage
bolts, 5/16” flat washers and 5/16”nyloc
nuts.
•Shown without pan for clarity.
TIGHTEN
Step 7 –Install Handle
•Use the hardware in the
rear bow to bolt handle
into position as shown.
TIGHTEN

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 15
Instructions –4A97L
Step 8 –Install Ladder Stop
•Use a 3/8” x 1” hex head bolt, two 3/8” flat washers and a 3/8” nyloc nut to attach the ladder
stop on the front bow. Be sure to place the tab on the ladder stop into the slot on the bow.
•Use the hardware in the rear bow to bolt ladder stop in orientation shown. Be sure to place
the tab on the ladder stop into the slot on the bow.
TIGHTEN
Front Bow shown below
Rear Bow shown below

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 16
Instructions –4A97L
Step 9 –Assemble Ladder Hooks
•Bolt ladder hook assembly to ladder hook weldment as shown.
•Use a 1/4" x 1" hex head, a 1/4" split lock washer and a 1/4" flat washer. This can be adjusted
later.
TIGHTEN

For Technical Support Call: 800-343-7486 Monday-Friday 7AM - 4 PM (PST) Page 17
Instructions –4A97L
Step 10 –Install Ladder Hooks
•Using the hardware and installed pem studs on both bows, loosen nuts and slide ladder hook
assembly into place.
TIGHTEN
GO BACK AND ENSURE ALL HARDWARE IS TIGHT
Your installation is now complete.