KBC ESUL8P-PC2-D User manual

Introduction
Welcome to KBC Network’s Quick Start Guide for
the ESUL8P PC2 and ESML8P PC2, 10 port, PoE
switches. This document provides some quick
tips on how to get up and running. For more
detailed information see the Downloads section
below.
Features:
• IEEE802.3af on 8 ports
• Dual redundant power input
• Alarm output for power supply
• Full & half duplex operation
• MDI/MDI X
• IP30 casing
Downloads
Installation manuals & specification sheets:
Other features and functions are described in the
unabridged manuals and specification sheets:
Unmanaged switch:
http://www.kbcnetworks.com/esul8p pc2
series/network products/esul8p pc2 series
Managed switch:
http://www.kbcnetworks.com/esml8p pc2
switch poe/network products/esml8p pc2 series
System Contents
Qty Description
1 Ethernet switch fitted with DIN rail mount.
2 Wall mount brackets with screws.
1 Pluggable terminal block.
Equipment equired for Physical
Deployment
You will need a 48Vdc power supply, these are
supplied separately.
Quick Start
Guide
ESUL8P-PC2-D* /
ES
M
L8P
-
PC2
-
D*
Industrial Ethernet Switch
QSG_ESUL8P-ESML8P-PC2-Rev1211 www.kbcnetworks.com
Copyright © KBC Networ s Ltd. 2012

Configuring the
ESU
L
8
P
-
PC2
-
D*
/ ESML8P-PC2-D*
1. Connect the DIN rail or wall mount
brackets as required.
2. Connect a 48Vdc power supply, (supplied
separately).
3. If using only one power source, connect
pin 1 to pin 5 and pin 2 to pin 6 otherwise
the Power Fail LED will be lit.
4. Install SFP modules as required.
5. Link external devices to the switch with
appropriate cables.
6. Connect the fault alarm contact if required.
Load External
power
24Vdc, 1A resistance
P Fail
LED Status Description
PWR1 ON Power is supplied to the unit
OFF No power to the unit
PWR2 ON Power is supplied to the unit
OFF No power to the unit
P Fail ON Power to PWR1 or PWR2 has failed
OFF Power is functioning to both or
none of the power inputs.
PoE 1 8 ON The port is supplying power to the
powered device.
OFF There is no powered device
attached or the power
to the device
has failed
Ethernet RJ45 Port P1 – P8 Status LED
Each RJ45 Ethernet port has two indicators. The yellow
lamp indicates port speed, and the green lamp indicates
port link state.
Lower OFF Full duplex link
FLASH Collisions are occurring
ON Half duplex link or no connection
Upper OFF Effective network connection has
been established for the port
FLASH Data traffic is passing through the
port
ON No effective network connection
has been established for the port
Ethernet RJ45 Ports P9 & P10 Status LED
Each RJ45 Ethernet port has two green indicators.
The yellow lamp indicates port speed, and the green
lamp indicates port link state.
Lower
LED
ON Power is supplied to the
unit
OFF Port not operating at
1000M or no connection
Upper
LED ON
Effective network
connection has been
established for the port
FLASH Data traffic is passing
through the port
OFF No effective network
connection has been
established for the port
Link/Active ON SFP port link
established
FLASH Active data flow
OFF No connection to the
network
Need Help?
Visit our website http://www.kbcnetworks.com or
contact your nearest KBC office or dealer:
US :
Phone: [phone]
Toll Free: [phone]
Email: [e-mail]
EME :
Phone: [phone]
Email: [e-mail]
P C:
Phone: [phone]
Email: [e-mail]
Quick Start Guide
ESUL8P-PC2-D* /
ESUL8P
-
PC2
-
D*
Industrial
Ethernet Switch
ESUL8P-PC2-D* / ESML8P-PC2-D*
LED Status Indicators
QSG-ESUL8P-ESML8P-PC2-Rev1211 www. bcnetwor s.com
Copyright © KBC Networ s Ltd. 2012