Kiloview E1-s User manual

E1-s Video Encoder
SDI video encoder
Leading solution provider of IP-based video transmission
Quick Start Guide
Contents
◼Packing List
◼Device interfaces and functions
◼Device connection, login and use guide
◼Device upgrade and restore to factory settings
Before using this product, it is recommended that you read the guide carefully. To ensure your personal safety and avoid physical or
electrical damage to the device, please strictly follow the instructions of this guide to install and use it under the guidance of
professionals. Incorrect electrical connections or physical installation may cause permanent damage to the device and even threaten
personal safety.

Page 1
Packing List
(1) Device ×1
(2) Power Supply×1
(3) Warranty Card×1
(4) Quick Start Guide×1
Device Interfaces
(1) Power port
(2) Mini USB
(3) 3.5mm line in/out
(4) SDI Input
(5) SDI Loop
(6) 100M Ethernet port
(7) Working indicators
(8) USB expansion port
(9) Micro SD/TF slot
(10) Power on /off
(11) Reset
10
11
1
2
3
4
5
6
7
8
9

Page 2
Device Indicators
Device Connection
LED Indicators
Name
Color
Status
Description
Power
Red
ON
Power connected
OFF
Power off or failure
Signal
Green
ON
SDI signal connected
OFF
SDI signal unconnected
Run
Green
Flashing
Working
ON
Starting
OFF
Device is abnormal or not started
SDI Video Source
LOOP
PC
AC100~240V
Switcher
Power Supply
Network

Page 3
Note
⚫Please use the equipped power adapter to power the device. Other unqualified power supplies may damage the device.
⚫Please make sure the camera is connected to the SDI IN port.
⚫Loop is not a must, you can connect to the SDI OUT port when loop out is needed.
Device Discovery
5.1 Direct visit by default IP
The default fixed IP address of E1-s is 192.168.1.168. Please configure your computer network to
192.168.1.xxx when you use it for the first time, and then enter http://192.168.1.168/ in the browser to visit
Web UI.
5.2 Use the free tool ---ONVIF Device Manager
Step 1: Start ONVIF Device Manager, all devices in the network can be found in the left device list.
Step 2: Click the device in the device list, the device information will be displayed in the information bar.
Website for more information on E1-s video encoder
https://www.kiloview.com/en/support/E1-s
Download the ONVIF Device Manager for free
Visit the website https://sourceforge.net/projects/onvifdm/ to download and install ONVIF Device Manager. Please
follow the software operation guidelines for the download method/installation.
ONVIF Device Manager is a network video app for managing network video, network video storage and network
video analysis to realize services such as discovery device, media, imaging, analysis and PTZ.

Page 4
Login to the device WEB page
Open a web browser and enter in the address bar: http://device IP address/login to the web UI.
Note
⚫The user name and password are admin by default.
⚫To ensure information security, it is recommended to change your password immediately after logging in for the first
time.
⚫Due to the browser compatibility issues, it is recommended to use Chrome or Edge.
Start a live streaming
7.1 Video source checking
When there is no video signal input, the Motion JPEG stream displays a blue image. If the video input, there
will be a real-time video displayed and changes every three seconds.
Introduction
⚫The working network that the device is connected needs to support DHCP. After the device automatically acquires the
IP, it can be discovered by the software through Onvif.

Page 5
Note
If the video source connected, there is still a blue screen or video displayed abnormality. Please check the input video source,
the video resolution format or cables, etc.
7.2 Encoding streams checking
1. Click "Encoding and Streaming" > "Encoding and Streaming Parameter Settings" on the web UI of E1-s;
2. In the H.264 stream, copy the URL address displayed on the right side of RTSP. The default RTSP URL of the
device is "rtps://device IP address: 554/ch01";
3. Open "Media" >“Network Streaming" of VLC;
4. Enter the URL address of RTSP in the network, and click the [Play] button in the lower right corner;
5. VLC will play the input video of device.
Download the VLC
Download and install the VLC through the official address https://www.videolan.org/vlc/. Please follow the official
guidelines of VLC for the download /installation.
VLC is a free, open source, cross-platform multimedia player and framework that can play most multimedia files, as
well as DVD, CD, VCD and various streaming protocols.

Page 6

Page 7
7.3 RTMP Pushing streaming live
1.Add an RTMP push point on the device side;
2.Click "Encoding and Stram" > "Encoding and Stream Settings" on the web UI of E1-s;
3.Click "Add a Streaming Service" under the H.264 main stream;
4.Select "RTMP Push" in the pop-up window ";
5.After confirmed, a push pint is generated.
Take FACEBOOK as an example, first obtain the RTMP push URL on the live platform. Login to FACEBOOK,
click "Live Video" to enter the live room, and click "Use Stream Key" for live broadcast. Fill in the URL of live
broadcast and Stream Key into the URL address of the RTMP push point, and start the streaming service.
You can see the video in the live broadcast room.

Page 8
Introduction
⚫If the platform RTMP streaming address and live broadcast code are separate, please use "/" to add the live broadcast
code after the RTMP address. The format is: rtmp address/live code.
⚫Please make sure the device is connected to the network, and configure the correct IP address, DNS and other
parameters.
Kiloview E1-s supports all the other stream services,for more information about the
E1-s streaming service,please visit.
https://www.kiloview.com/en/support/docs/E1-s/

Page 9
Firmware Upgrading
8.1 Download firmware
8.2 Upgrade device firmware
Login to the web page of E1-s, click "Settings">"Firmware Upgrade" to check if there is any latest firmware
available to download.If yes,select the downloaded firmware and click “Firmware Upgrade”.
After uploaded the firmware successfully, it needs to reboot the device. After clicking “ok”, the device will
restart, please be patient.
Note
⚫Please do not power off during the upgrade process, otherwise the device couldn’t work.
⚫Generally, it will take 3-5 minutes to upgrade the device. If it’s still not completed after 5 minutes, please try refreshing
webpage, if you still can’t access it, please try to contact for technical support.
Kiloview will provide the firmware of updating functions for E1-s, please visit.
https://www.kiloview.com/en/support/download/
Select “video encoders” > “E1-s”, find and download the latest firmware.

Page 10
Restore to factory settings
If the device cannot work normally after modified the parameters or forgot internet IP configuration and
couldn’t search and find the device, please restore factory settings.
Two methods for restoring factory settings:
1) If you can login to web page, then via the web page, click "Settings>System settings>Restore factory
settings".
2) If you can’t login to web page, press the RESET button for 5 seconds in the bottom of device.
Note: After restoring factory setting, below parameters will be turned to default value:
⚫Login username and password will be “admin”.
⚫Your device will be restored to obtain a DHCP-assigned IP address by default and the failover address 192.168.1.168 will
be bound to the device.
⚫All encoding parameters of video and audio will be restored to default value.
Others
To prolong the device life，please unplug the power and keep it properly if you do not use it for a long time.

Page 11
Any In,Any Out,Anywhere
For more questions, please contact us via：
https://www.kiloview.com/en/support
KILOVIEW Electronics CO., LTD.
Tel：[phone] Email：[e-mail] Web：www.kiloview.com/en
Address: B4-106/109, Jiahua Intelligence Valley Industrial Park, 877 Huijin Road, Yuhua District,
Changsha City, Hunan Province, China.