Kimo LV 130 User manual

PERFORM A MEASUREMENT
➢Turn on the device by pressing on «On/Off/Esc».
The device displays its name «LV130».
➢Put the probe to the required location.
The device displays the velocity and temperature measurements.
Van probe thermo-anemometer
LV 130
DESCRIPTION OF THE DEVICE
OK key
Hold/min/max key
Select key
Backlight key On/Off/Esc key
FREEZE THE MEASUREMENT
During the measurement:
➢Press once on «Hold/min/max».
«Hold» appears on screen and the measurement is frozen.
➢Press on « On/Off/Esc» to exit the hold function.
The device returns to the measurement display.

ADJUST THE DEVICE
PERFORM AN AVERAGE IN VE OCITY
The device is on and displays the measurement:
➢Press on « OK».
«START» displays on screen.
➢Press on «OK», the average calculation is launched, «END» displays on screen and «AVG» blin s.
➢Press on «OK» to stop the average calculation, the average displays.
➢Press on « OK» to display the maximum and minimum values measured during the calculation of this average.
➢Press on «On/Off/Esc» to exit the average function and return to the measurement display.
DISP AY AND MEASURE THE AIRF OW
It's possible to display and measure the airflow in place of velocity.
The device is on and displays the velocity and temperature measurement.
➢Press on «Select».
«MODE» blinks on screen.
➢Press on «OK».
«VELO» blinks at the bottom of the screen.
➢Press on «Select» to select the «F OW » mode then press on «OK» to validate.
➢«CIRC» blin s on screen, press on « Select» to ma e appear «K 25 85» then «RECT».
➢Press on «OK » to validate.
●If «RECT» or «CIRC» are selected, the measuring unit of the duct type displays.
➢Press on « Select » to select the unit: mm or inch then press on «OK » to validate.
●If the type of selected duct is circular: « DIAM » displays and the first digit blin s.
Press on «+Select+» to select its value then press on «OK » to validate. Perform the same procedure to select the value of the
following digits (to return to the previous digit press on « On/Off/Esc » . When the last digit is adjusted, press on «OK+» to validate.
The device return to the display of airflow and velocity measurements.
●If the type of selected duct is rectangular: « ENGT» displays and the first digit blin s.
●Press on «Select» to select its value then press on «OK» to validate. Perform the same procedure to select the value of following
digits (to return to the previous digit press on « On/Off/Esc » . When the last digit is adjusted, press on «OK ».
«WIDTH» to adjust the width, displays on screen, perform the same procedure to select the digits value, when the last digit is
adjusted press on «OK » to validate. The device returns to the display of the airflow and temperature measurements.
●If «K 25 85» is selected: the device returns to the measurements display.
The length, the width and the section diameter are adjustable from 1 to 3000 mm.
●Device drop-down menu
SE .
BEEP
ON
Select Select
SE .
AUTO
OFF
OFF
SE .
UNIT
m/s
3x 4x2x
Select
SE .
UNIT
°C
SE .
MODE
VELO
1x
Select
Select
5x
Once the measurement is frozen:
➢Press once on « Hold/min/max ».
➢The device displays the maximum value of velocity or airflow measured since the last questioning at the top of the screen and the minimum
value of velocity or airflow since the last questioning at the bottom of the screen.
➢Press once on «Hold/min/max ».
The device displays the maximum value of temperature measured since the last questioning at the top of the screen and the minimum value
of temperature measured since the last questioning at the bottom of the screen.
➢Press on «On/Off/Esc » to exit the hold function.
The device returns to the measurements display.
DISP AY THE MINIMUM AND THE MAXIMUM

Select the measuring unit in temperature+:
The device is on and display the measurements.
➢Press on «Select» until «UNIT» blin s on screen with the temperature unit displayed below.
➢Press on «OK».
The unit currently used blinks at the bottom of the screen.
➢Press on «Select» until the required unit appears: °C or °F.
➢Press on «OK» to validate.
«UNIT» blinks on screen.
➢Press on «On/Off/Esc» to return to the measurement display.
Select the measuring unit in airflow+:
The device is on and in velocity mode.
➢Press on «Select » until «UNIT» blin s on screen with the airflow unit displayed below.
➢Press on «OK».
The unit currently used blinks on screen.
➢Press on «Select» until the required unit appears: m3/h, L/s, cfm or m3/s.
➢Press on «OK» to validate the unit selection.
«UNIT» blinks on screen.
➢Press on «On/Off/Esc» to return to the measurement display.
Select
UNIT
SE .
°C
OK
SE .
UNIT
°C
OK
0,00
m/s
77,3
°F
UNIT
SE .
°C / °F
SE .
UNIT
°F
On/Off/
Esc
Select the measuring unit in velocity :
The device is on and in velocity mode.
➢Press on « Select» until «UNIT» blin s on screen with the velocity unit displayed below.
➢Press on « OK ».
The unit currently used blinks on screen.
➢Press on «Select» until the required unit appears: m/s, fpm or m/h.
➢Press on «OK» to validate the unit selection.
«UNIT» blinks on screen.
➢Press on « On/Off/Esc» to return to the measurement display.
Select
SE .
UNIT
m/s
OK UNIT
SE .
m/s
UNIT
SE .
m/s / fpm...
SE .
UNIT
fpm
Select On/Off/
Esc
0,00
fp/m
25,4
°C
On/Off/
Esc
Select OK
OK
SE .
UNIT
m3/h
SE .
UNIT
L/s
UNIT
SE .
m3/h
0
L/s
25,4
°C
UNIT
SE .
m3/h / L/s...

➢Remove the front part at the bac of the device.
➢Change the old batteries by AAA LR03 1.5V batteries.
Replace the front part.
CHANGE THE BATTERIES
ACTIVATE THE B ACK IGHT
The device is on.
➢Press on «Backlight»: to activate the device blac light.
➢Press again on this ey to deactivate the bac light.
Activate or deactivate the key beep+:
The device is on and displays the measurement.
➢Press on «Select » until « BEEP» blin s on screen.
➢Press on «OK».
«OFF» or «ON» blinks on screen.
➢Press on «Select+» to activate the ey beep «ON» or deactivate it «OFF».
➢Press on «OK» to validate.
«BEEP» blinks on screen.
➢Press on «On/Off/Esc» to return to the measurement display.
OK
BEEP
SE .
OFF / ON
SE .
BEEP
ON
OK BEEP
SE .
ON
SE .
BEEP
OFF
Select On/Off/
Esc
0,00
m/s
25,4
°C
Adjust the auto shut-off+:
The device is on and displays the measurement.
➢Press on «Select » until «AUTO OFF» blin s on screen.
➢Press on «OK».
The time before device auto shut-off blinks at the bottom of the screen.
➢Press on «Select» until the required time before auto shut-off appears: 15, 30, 45, 60, 75, 90, 105, 120 minutes or OFF.
➢Press on «OK» to validate.
«AUTO OFF» blinks on screen.
➢Press on «On/Off/Esc» to return to the measurement.
AUTO
OFF
15 / 30mn...
AUTO
OFF
OFF
OK
Select On/Off/
Esc
0,00
m/s
25,4
°C
SE .
AUTO
OFF
OFF
SE .
AUTO
OFF
30mn
OK
Once returned to KIMO, required waste collection will be assured in the respect of the environment in accordance to 2002/96/CE guidelines relating to WEEE
NTang – portable-LV130 – 10/06/14 – RCS (24) Périgueux 349 282 095 Non-contractual document – We reserve the right to modify the characteristics of our products without prior notice.