Kimo TR110 User manual

PERFORM A MEASUREMENT
➢Turn on the device by pressing on «On/Off/Esc».
The device displays its name «TR110» or «TR112».
●Put the probe to the required location.
The device displays the temperature measurement with below the type of thermocouple.
If the used thermometer is the TR112with two connected probes, the device will display the two measurements.
➢Press on « OK» to display the delta between the two temperatures.
PT100 thermometer
TR 110 – TR 112
DESCRIPTION OF THE DEVICE
OK key
Hold/min/max keySelect key
Backlight key On/Off/Esc key
uring the measurement:
➢Press once on «Hold/min/max».
«Hold» appears on screen and the measurement is frozen.
➢Press on « On/Off/Esc» to exit the hold function.
The device returns to the measurements display.
FREEZE THE MEASUREMENT
[e-mail]
DigiParts GmbH

ADJUST THE DEVICE
Select
SEL.
U IT
C°
SEL.
AUTO
OFF
OFF
2x 3x
SEL.
BEEP
OFF
Select
1x Select
Select the tempe atu e unit :
The device is on and displays the measurement.
➢Press on « Select» until «UNIT» blinks on screen.
➢Press on « OK ».
The unit currently used blinks on screen.
➢Press on «Select» until the required unit appears: °C or °F.
➢Press on «OK» to validate the unit selection.
«UNIT» blinks on screen.
➢Press on «On/Off/Esc» to return to the measurement display.
On/Off/
Esc
OK
U IT
SEL.
C°
SEL.
U IT
F°
U IT
SEL.
C° / F°
SEL.
U IT
C°
Select
77.5
°F
OK
●Device d op-down menu
DISPLAY THE MINIMUM AND THE MAXIMUM
Once the measurement is frozen:
➢Press once on « Hold/min/max ».
●If the device is a «TR110» or a «TR112» with one connected probe, the device displays the maximum value measured since the last
questioning at the top of the screen and the minimum value measured since the last questioning at the bottom of the screen.
●If the device is a «TR112» with two connected probes, the device displays the maximum value of the probe C1 measured since the last
questioning at the top of the screen and the minimum value of the probe C1 since the last questioning at the bottom of the screen.
➢Press again on «Hold/min/max » if the device is a «TR112» with two connected probes.
The device displays the maximum value of the probe C2 measured since the last questioning at the top of the screen and the minimum value
of the probe C2 since the last questioning at the bottom of the screen.
➢Press on «On/Off/Esc » to return to the measurement display.
Adjust the auto shut-off0:
The device is on and displays the measurement.
➢Press on «Select » until «AUTO OFF» blinks on screen.
➢Press on «OK».
The time before device auto shut-off blinks at the bottom of the screen.
➢Press on «Select» until the required time before auto shut-off appears: 15, 30, 45, 60, 75, 90, 105, 120 minutes or OFF.
➢Press on «OK» to validate.
«AUTO OFF» blinks on screen.
➢Press on «On/Off/Esc» to return to the measurement display.
SEL.
AUTO
OFF
OFF
Select
SEL.
AUTO
OFF
30mn
AUTO
OFF
15 / 30mn...
24.5
°C
AUTO
OFF
OFF
OK On/Off/
Esc
OK
[e-mail]
DigiParts GmbH

Adjust the ala m0:
This function allows to activate a temperature alarm on the channel 1 when the device reaches and exceeds a previously defined threshold.
This threshold will be between -100 and +400°C.
The device is on and displays the measurement.
➢Press on «Select» until «AL 1 » blinks on screen.
➢Press on «OK ».
The first digit blinks. This first digit also allows to deactivate the alarm.
➢Press on «Select» to select its value: -, 0 or off.
●If OFF is selected, the alarm is deactivated. Press on «OK» to validate, «AL 1» blinks.
●If 0 or – is selected, press on «OK». The following digit blinks, press on «Select» to select its value (between 0 and 4) then press
on «OK». Perform the same procedure to select the value (0 and 9) of the following digits (press on «On/Off/Hold» to return to
the previous digit). Press on «OK» when the first digit is adjusted: «AL 1» blinks.
➢Press on «On/Off/Esc» to return to the measurement display.
Activate o deactivate the keys beep0:
The device is on and displays the measurement.
➢Press on «Select » until « BEEP » blinks on screen.
➢Press on «OK».
«OFF» or «ON» blinks on screen.
➢Press on «Select » to activate the keys beep «ON » or deactivate it «OFF» .
➢Press on «OK» to validate.
«BEEP» blinks on screen.
➢Press on «On/Off/Esc» to return to the measurement display.
OK
SEL.
BEEP
OFF
BEEP
SEL.
OFF / O
SEL.
BEEP
O
Select
24.5
°C
OK On/Off/
Esc
BEEP
SEL.
O
ACTIVATE THE BAC LIGHT
The device is on.
➢Press on «Backlight»: to activate the device backlight.
➢Press again on this key to deactivate the backlight.
➢Remove the front part at the back of the device.
➢Change the old batteries by AAA LR03 1.5V batteries.
➢Replace the front.
CHANGE THE BATTERIES
[e-mail]
DigiParts GmbH