Kingfisher KI6102 Series User manual

Revision 7 Date: 22 Jun 2020 Page 1 of 13
User Manual
KI6102 series PON Power Meter
Warranty:
Information in this manual is given in good faith for the benefit of the user. It
cannot be used as the basis for claims against Kingfisher International or its
representatives, if accidental damage or inconvenience results from use or
attempted repair of the equipment.
This Kingfisher International product is guaranteed against defective
components and workmanship for a period of 1 year from the date of delivery,
unless specifically stated in the original purchase contract or agreement.
This warranty excludes optical connectors or incorrect use.
The warranty will be voided if the following instance happens:-
1) Opening the instrument.
2) The instrument has been immersed in water or subjected to extreme
environmental conditions.
Liability is limited solely to repair of the equipment.

Revision 7 Date: 22 Jun 2020 Page 2 of 13
CONTENTS
1. Technical specifications .......................................................................3
2. The Instrument .......................................................................................4
3. Operation Instructions ..........................................................................6
3.1 ON/OFF Instrument .........................................................................6
3.2 Auto Power Off ................................................................................6
3.3 Back Light ........................................................................................7
3.4 Selecting Measurement Unit ...........................................................7
3.5 Relative Measurement Mode ..........................................................7
3.6 Threshold Setup ..............................................................................7
3.9 Save, Retrieve/view, Delete Test Data ............................................9
3.10 Battery .........................................................................................10
4. Maintenance ......................................................................................... 11
5. Content of Packing ...............................................................................12
6. Safety ....................................................................................................12

Revision 7 Date: 22 Jun 2020 Page 3 of 13
1. Technical specifications
.
Standard wavelengths
1310
(upstream test)
1490
(downstream test)
1550
(downstream test)
Pass zone(nm)
1260 ～1360
1470 ～1505
1535 ～1570
Range(dBm)
-40 ～+10
-45 ～+10
-45 ～+23
Isolation @1310nm(dB)
> 40
> 40
Isolation @1490nm(dB)
> 40
> 40
Isolation @1550nm(dB)
> 40
> 40
Uncertainty(dB)
±0.5
Polarization Dependent
Loss (dB)
< ±0.25
Linearity(dB)
±0.1
Through Insertion
Loss(dB)
< 1.5
Resolution
0.01dB
Measurement unit
dBm / dB / W / Pass / Fail
Memory capacity
99 test
Auto backlight off time
30 seconds
Auto power off time
10 minutes
Battery type
KI6102-xx series: 7.4V 1000mAH rechargeable Lithium battery
KI6102AA-xx series: 4x AA non-rechargeable battery
Battery life
18 hours with rechargeable Lithium battery or 4x AA batteries
Operating / storage
temperature
-10 ~ 60 ℃/ -25 ~ 70 ℃
Dimensions / Weight
200 * 90 * 43 mm / 330g

Revision 7 Date: 22 Jun 2020 Page 4 of 13
2. The Instrument
Figure 1: Front view
Rubber
holster
Optical ports

Revision 7 Date: 22 Jun 2020 Page 5 of 13
Figure 2: Top View
ONT Port: for 1310nm upstream signal test.
OLT Port: 1490/1550 nm downstream signal test.
Figure 3: Side View
USB connector: Connects instrument to a computer.
Charging Hole: Insert connector of the charger to charge instrument (for
KI6102-XX series only).
ONT Port
OLT Port

Revision 7 Date: 22 Jun 2020 Page 6 of 13
3. Operation Instructions
3.1 ON/OFF Instrument
Press and hold [ON] to turn on instrument; the Home Display below will be
seen on screen as shown below.
3.2 Auto Power Off
Auto Power Off mode is enabled when instrument is first turned on. The
symbol, “ ” indicates that Auto Power Off mode is enabled.
When Auto Power Off mode is enabled, instrument will turn off automatically
if no subsequent key is pressed 10 minutes after it was turned on.
At Home Display, press [OFF] to disable or enable Auto Power Off mode.
The instrument is now ready for
measurements. Powers levels of
the respective wavelengths will be
displayed automatically when live
fibers are appropriately connected
to the OLN & OLT ports.
To turn off instrument, press and
hold [OFF].
Indicates calibration settings are of factory default
Indicates back light is on
Indicates Auto Power Off mode is enabled

Revision 7 Date: 22 Jun 2020 Page 7 of 13
3.3 Back Light
Backlight turns on when instrument is first turned on and goes off after 30
sec.
When backlight is off, press any key to turn it back on for 30 sec.
3.4 Selecting Measurement Unit
At Home Display, press [F2] to select measurement unit (dBm or W).
3.5 Relative Measurement Mode
At Home Display, press and hold [▼] to enter Relative Measurement mode;
the displayed measurement unit will change to dB. Press [F2] to exit Relative
Measurement mode.
3.6 Threshold Setup
3.6.4 When a wavelength is selected, press and hold [OK] to enter Threshold
Editing mode.
Use [◄, ►] to move cursor onto threshold type & onto digit to be edited; the
selected digit will blink.
3.6.1 At Home Display, press and hold [▲]
to enter Threshold Management Display,
see picture on the right.
3.6.2 Choose a threshold group number
from the available 01, 02, 03 using [▲, ▼].
3.6.3 When a threshold group is selected,
use [◄, ►] to select wavelength from the
available 1310, 1490, 1550 nm.
Selected threshold group

Revision 7 Date: 22 Jun 2020 Page 8 of 13
Use [▲, ▼] to change value of selected digit and [▼] to change the sign
(positive or negative) of a set value.
Set the 3 displayed thresholds types (see below) with the desired values:
ALARM (displayed as “ ! ”)
PASS (displayed as “ √ ”)
FAIL (displayed as “ x ”)
Press [OK] to save settings. Note that if an invalid threshold value was entered, it
will exit from Threshold Editing Mode & return to Home Display without saving.
Use [►] to select the next wavelength and set the respective thresholds by
repeating steps in 3.6.4.
3.6.5 Press [OFF] to exit Threshold Editing Mode and return to Home Display.
The Threshold Management Display or Threshold Editing Mode will exit
automatically if no subsequent key is pressed 10 sec after being selected.
3.7 Measurement with Pass/Fail Display Mode
At Home Display, press and hold [▲] to enter Threshold Management
Display, see picture below.
The pass/fail/alarm
sign
displayed beside
each measurement
reading to show their
respective test result.
Selected threshold group

Revision 7 Date: 22 Jun 2020 Page 9 of 13
Choose a threshold group number (from the available 01, 02, 03) using [▲,
▼].
Press [OK] to activate Pass/Fail display mode.
Press and hold [OK] to de-activate Pass/Fail display mode.
3.8 Setting Time
At Home Display, press and hold [►] to enter Time Setting mode.
Use [◄, ►] to select digit to be edited; the selected digit will blink. Use [▲,
▼] to edit the value of the selected digit. Press [OK] to save changes or press
[OFF] to exit Time Setting mode without saving.
Date format: YY/MM/DD
Time format: HH:MM
Time Setting mode will exit automatically if no subsequent key is pressed 10
sec after it was selected.
3.9 Save, Retrieve/view, Delete Test Data
To save data:
At Home Display, press [F1]; the blinking symbol, “ ” indicates that
instrument is in Data Saving mode.
Press [OK] to save existing test data onto internal memory or press [OFF] to
exit without saving.
Data Saving Mode will exit automatically if no subsequent key is pressed 10
sec after being selected. A max of 99 records can be saved.

Revision 7 Date: 22 Jun 2020 Page 10 of 13
To read retrieve/read saved data:
At Home Display, press and hold [◄] to enter Data Browsing mode, see
picture below.
Use [▲, ▼] to choose test data record saved in instrument’s memory. The
chosen test data record is displayed with date, record number and time
information.
To delete all data records: Press and hold [OK].
Test Data Browsing mode will exit automatically if no subsequent key is
pressed 10 sec after it was selected.
3.10 Battery
When battery voltage drops below 6.7volt (for Lithium battery), the indicator,
“ ” will be displayed and instrument will beep for a short instant before
powering off automatically. Recharging (for KI6102-xx only) takes 4 - 6 hours;
charging indicator on charger turns green when instrument is fully charged.
See Section 4 (Maintenance) for instructions to replace AA batteries.
Indicates Data
Browsing mode
Selected test data record number

Revision 7 Date: 22 Jun 2020 Page 11 of 13
4. Maintenance
4.1 Keep the sensors’ surfaces clean and free of dust or other contaminant
by cleaning them regularly.
4. 2 Do not use unclean or nonstandard adapters.
4.3 Change adapter carefully if necessary and keep any spare adapter in
dirt/dust free environment.
4.4 When the instrument is not in use, keep the optical connectors covered
with dust caps at all the time. Exposing the sensor for a long period of time
will allow dust to be accumulated on surface of the sensor; this will in turn
result in measurement inaccuracy.
4.5 Consider leaving test cords connected to the PON meter at all times.
This will prolong the life of the instrument ONT & OLT connectors.
4.6 Instruction to replace AA batteries (for KI6102AA-xx series only).
➊ Remove instrument from rubber holster.
➋ Hold instrument with its back facing up as shown in picture below.
➌ Press down with both thumbs near arrow sign, push battery cover in direction
shown by the arrow sign.
❹ Remove battery cover, replace all the 4 batteries. Make sure batteries are
inserted with the correct polarities.
➎ Replace battery cover followed by rubber holster of instrument.
Arrow sign on
battery cover

Revision 7 Date: 22 Jun 2020 Page 12 of 13
5. Content of Packing
Description
Quantity
KI6102-APC
KI6102AA-APC
AA Battery
-
4
External power supply/charger
1
-
PON Power meter
1
1
User manual
1
1
Soft carry pouch
1
1
SC/APC--SC/APC or SC/PC--SC/PC Patchcord
1
1
Software CD
1
1
USB cable
1
1
Cleaning cotton stick pack
1
1
For KI6102-xx series, select from the option part number listed below to order
suitable AC power adapter plug if needed;
6. Safety
Take appropriate eye-safe precautions when
handling live fibre.
Avoid condensation
The instrument is resistant to normal dust and moisture, however it is not
waterproof. If moisture gets into the instrument, remove the batteries and
dry it out carefully for at least one hour before using it again.
Description
P/N
AC Power Adapter Plug , US-to-UK
OPT093
AC Power Adapter Plug, US-to-AUS
OPT094
AC Power Adapter Plug, US-to-EUR
OPT095

Revision 7 Date: 22 Jun 2020 Page 13 of 13
Storage
During prolonged storage, remove batteries to eliminate the possibility of
acid leakage. Use only high quality batteries.