Kleenmaid GCT6010 User manual

cooking collection
Instructions for use and warranty details
Gas Cooktop
Model No.: GCT6010 and GCT9010

2

3
Your new Kleenmaid appliance has been
designed and manufactured to give you
years of reliable performance.
For best results, carefully read the
instructions on how to install your new
appliance. Correct installation will avoid
delays and unnecessary service call costs.
Once installation is complete, please read
this entire instruction manual carefully and
get to know the controls and the features
of your new Kleenmaid appliance.
Again, congratulations and thank you for
choosing Kleenmaid.
Congratulations on the purchase
of your new Kleenmaid appliance.

4
Dear Customer,
we would like to thank you and congratulate you on
your choice.
This new product has been carefully designed and built
using top quality materials, and meticulously tested to
ensure that it meets all your culinary requirements.
Please read and observe these simple instructions,
which will enable you to achieve excellent results
from the very first time you use it. This state-of-the-
art appliance comes to you with our very best wishes.
THE MANUFACTURER
THIS PRODUCT IS DESIGNED FOR DOMESTIC
USE.
THE MANUFACTURER DECLINES ALL
RESPONSIBILITY FOR DAMAGES TO THINGS
OR PEOPLE DERIVING FROM INCORRECT
INSTALLATION OR IMPROPER, ERRONEOUS OR
UNSUITABLE USE.
THE APPLIANCE MUST NOT BE USED BY
PEOPLE (INCLUDING CHILDREN) WITH PHYSICAL,
SENSORIAL OR MENTAL IMPAIRMENTS, OR BY
PEOPLE WITHOUT THE NECESSARY EXPERIENCE
OR KNOWLEDGE, UNLESS THEY ARE SUPERVISED
OR INSTRUCTED IN THE USE OF THE APPLIANCE
BY A PERSON RESPONSIBLE FOR THEIR SAFETY.
CHILDREN MUST BE SUPERVISED TO ENSURE
THAT THEY DO NOT PLAY WITH THE APPLIANCE.

5
General information
Please read this booklet thoroughly before you use
this appliance. It is important that you understand
all the control functions before commencing to cook
with your Kleenmaid appliance.
Please remember the advice and warnings shown
on the page, which is headed ‘WARNING AND
SAFETY INSTRUCTIONS -IMPORTANT NOTE’.
This appliance is designed for domestic household
use when built into a kitchen worktop.
NOTE: The housing, adjacent furniture and all materials used in
the installation must be able to withstand a minimum temperature
rise of 85°C above ambient during periods of operation. This
information is for guidance only and the actual withstand
temperature will depend on the performance rating for the surface
finish of the worktop.
Certain types of kitchen furniture surface finishes are
particularly prone to heat damage or discolouration
at temperatures lower than the above guidelines.
Installing the appliance in contravention of the
guidance given will be at the liability of the owner.
The use for any other purpose or in any other
environment without the express agreement of
Kleenmaid, would invalidate any warranty or
liability claim. Your new appliance is guaranteed
against electrical or mechanical defects subject to
certain exclusions noted in Kleenmaid Conditions
of Warranty. The foregoing does not affect your
statutory rights.
In the event that you require any After Sales Service
or advice, www.kleenmaid-appliances.com.au
Before using this appliance ensure that any protective
packaging or coatings have been removed. To aid
the protection of the environment, please sort the
packing materials into different types and dispose
of them in accordance with the local waste disposal
laws. Any further information can be obtained from
your local Environment Agency office.
When first used, an odour may be emitted by any
residual protective finish or moisture, which will
cease after a short period of time.
This appliance has been constructed and distributed
in compliance with the essential requirements of
the following EEC DIRECTIVES and EUROPEAN
NORMS: and AUSTRALIAN STANDARDS and
SAFETY REGULATIONS
CE Marking – 93/68 Low Voltage – 73/23 Gas
Products- 90/396/AG101
EMC – 89/336
Materials that can touch food – 89/109.
Safety Standards – EN 60 335-1, EN 60 335-2-6,
EN 30-1-1. AS/NZS 3350-1, 3350-2-6
As Kleenmaid have a policy of continued product
improvement, the right is reserved to adjust and
make any modifications deemed necessary without
notification.

6
Warning and safety instructions
IMPORTANT NOTE
This appliance complies with all current European
safety legislation, however Kleenmaid do wish to
emphasise that compliance does not remove the
fact that surfaces will become hot during use and
retain heat after operation.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Children should be supervised to ensure that they
do not play with the appliance.
• A steam cleaner is not to be used on this
appliance.
• We also advise that great care is taken during use
and cleaning operations.
• Do make sure that the pan handles are always
correctly positioned to avoid accidental contact.
• Do not leave heated oil or fat unattended· as there
is a risk of fire.
• Do use pans that are flat bottomed and the
correct size for the heating area to be used (never
smaller).
• Do not allow electrical fittings or cables to be in
contact with hot areas of the appliance.
• Do not use the appliance for space heating or to
dry clothes.
• Do not install the appliance next to curtains or soft
furnishings.
DO NOT SPRAY AEROSOLS IN THE VICINITY OF
THIS APPLIANCE WHILE IT IS IN OPERATION.
WHERE THIS APPLIANCE IS INSTALLED IN
MARINE CRAFT OR IN CARAVANS, IT SHALL NOT
BE USED AS A SPACE HEATER.
DO NOT STORE OR USE FLAMMABLE LIQUIDS
OR ITEMS IN THE VICINITY OF THIS APPLIANCE.
UNLESS EACH BURNER IS FITTED WITH A
FLAME SAFEGUARD, THE APPLIANCE IS
NOT SUITABLE FOR USE IN MARINE CRAFT,
CARAVANS OR MOBILE HOMES.
Do Not Modify This Appliance
Kleenmaid declines any responsibility for injury
or damage to persons or property as a result of
improper use or installation of this appliance.
Heat, steam and moisture will be created during
use, take care to avoid injury and ensure that the
room is adequately ventilated. If prolonged use
occurs, additional ventilation may be required-
please consult your Qualified Installer if you are in
any doubt about the amount required.

7
User instructions
These user instructions should be retained for future
reference and for use by a person who is perhaps
unfamiliar with the appliance.
The following models are covered by these
instructions:
GCT6010 – 4 burner (including wok), stainless steel
hob, standard enamel or optional cast iron trivets
with flame failure & auto ignition
GCT9010 – 5 burner {including wok), stainless steel
hob, cast iron trivets with flame failure & auto ignition
Using the cooktop
The symbols on the Control Panel fascia show which
burner the Control Knob operates. Dependent on
the model there are two methods for igniting the
burners.
1. Auto Ignition
After pressing in and turning the appropriate knob
anti-clockwise to the large flame symbol; the ignition
spark will operate as long as the knob is pressed
down. When a flame has been established the knob
can be released.
2. Manual ignition
After pressing in and turning the appropriate knob
anti-clockwise to the large flame symbol, press the
ignition button located on the control panel. The
ignition spark will operate as long as the button is
held down. When a flame has been established,
release the button. To regulate the flame, continue
turning anti-clockwise to the required setting
between the large and small flame symbols. To turn
the burner off, turn fully clockwise
Important
Gas Protekt
On models with thermoelectric protection (Gas
Protekt) do not keep the ignite button pushed for
more than 15 seconds. If the burner has not ignited
after 15 seconds, open the door of the room
and wait at least one minute before making a
further attempt.
Maintenance Gas/Electrical
Prior to any maintenance, disconnect the appliance
from the electrical system. For long-life to the
equipment, a general cleaning operation must take
place periodically, bearing in mind the following:
• The glass, steel and/or enamelled parts must be
cleaned with suitable non-abrasive or corrosive
products (found on the market). Avoid chlorine-
base products (bleach, etc.);
• Avoid leaving acid or alkaline substances on the
working area (vinegar, salt, lemon juice, etc.);
• The wall baffle and the small covers (mobile
parts of the burner) must be washed frequently
with boiling water and detergent, taking care to
remove every possible encrustation. Dry carefully
and check that none of the burner holes is fully or
partially clogged;
• the electrical parts are cleaned with a damp cloth
and are lightly greased with lubricating oil when
still warm;
• the stainless steel grids of the working area, after
having been heated, take on a bluish tint which does
not deteriorate the quality. To bring colour back to its
original state, use as lightly abrasive product.
N.B.- Cleaning of the taps must be carried out by qualified
personnel, who must be consulted in case of any functioning
anomaly. Check periodically the state of condition of the flexible
gas feed pipe. In case of leakage, call immediately the qualified
technicians for its replacement.
DO NOT USE STEAM CLEANERS
Gas
wok
Ø 20-32 fast
Ø 20-26 semi fast
Ø 14-20 auxiliary*
Ø 10-14
* with reduction grid

8
Installation instructions
This appliance must be installed only by authorised
personnel and in accordance with manufacture’s
installation instructions, local gas fitting regulations,
municipal building codes, water supply regulations,
electrical wiring regulations AS 5601/AG601- Gas
Installations and any other statutory regulations.
• Gas safety regulations (Installation & Use)
• Kleenmaid Installation Instructions.
Installation notes
1. Cut the aperture to the dimensions shown below
or use the template if printed on the packaging.
2. Invert the cooktop and apply the sealing agent
provided to match the outer perimeter edge.
3. If the sealing agent is a strip type, the protective
covering must be removed from both sides. Do
not leave a gap in the sealing agent or overlap the
thickness.
4. NOTE: Do not use any Silicone based sealant, as
this can damage the worktop surface if repairs
are required.
5. Insert the appliance into the aperture and fix in
position via the clamps & screws, tightening the
screws evenly (see Fig 2 below).
Positioning
The appliance can be fitted into a working area
as illustrated on the corresponding figure. Before
positioning the hob, fit the seal
around the entire periphery
of the hole cut in the worktop.
Ventilation of rooms
The room in which this appliance is installed must be
well ventilated by natural or mechanical means or a
combination of both to ensure correct combustion
and the removal of spent air. The minimum quantity
of air for combustion will depend on the room
volume, number of appliances and their total power
rating. The power rating of your appliance can be
found by reference to the Rating Plate.
NOTE: The actual ventilation requirements must be determined
by reference to the Statutory Regulations in force
X
Figure 2

9
Gas connection
Data Label – The Data Label is located on the
underside of the appliance. A duplicate label is
supplied to adhere in an accessible area adjacent to
the appliance. This appliance is suitable for Natural
Gas and propane Gas; ensure that the available gas
supply matches the Data Label
The appliance is factory set for Natural gas but
can be converted to LPG (Propane). The test point
pressure should be adjusted to 1.00 kPa for Natural
Gas and 2.75 kPa for Propane, with the relevant
burners operating at maximum as in the table above.
Connect the appliance to the gas cylinder or to the
installation according to the prescribed standards
in force, and ensure beforehand, that the appliance
matches the type of gas available. Otherwise, see
”Adaptation to various types of gas”. Furthermore,
check that the feed pressure falls within the values
described on the table. ”User characteristics ”.
When converting from Natural Gas to Propane ensure
that the NG regulator is removed and replaced with
the Test Point Assembly. A gas regulator suitable
for a supply pressure of 2.75 kPa should be part of
the gas tank supply. Replace the old data plate with
one, which is suitable for the type of gas for which
the appliance has been regulated.
The gas supply must be connected by use of the
1/2” BSP Elbow, Seal and copper pipe and an
isolation tap fitted in an easily accessible position.
Model T.P.P. (kPa) Burners
Natural Gas Propane (LPG)
GCT6010 12.75 Wok+ Rapid
GCT9010 12.75 Wok+ Rapid
Figure 5

10
Gas flow adjustment
In order to adjust the minimum gas flow proceed as
follows:
• Ignite the burner and turn down to the minimum
setting.
• Remove the control knob from the gas tap.
• Adjust the flow either clockwise to decrease
or anti-clockwise to increase the flame. Use a
screwdriver inserted down the gas tap rod or via
the screw head adjacent to the rod for models
fitted with a Flame Supervision Device.
• Check that the flame is 3- 4 mm in length, bluish
in colour, stable and noiseless, and does not
extinguish when changing from maximum to
minimum flow.
• Replace the control knob and check that all
components have been reassembled ·correctly.
Before leaving – Check all connections for gas leaks
with soap and water. DO NOT use a naked flame for
detecting leaks. Ignite all burners to ensure correct
operation of gas valves, burners and ignition. Turn
gas taps to low flame position and observe stability
of the flame. When satisfied with the hotplate, please
instruct the user on the correct method of operation.
In case the appliance fails to operate correctly after all
checks have been carried out, refer to the authorised
service provider in your area.
Adaptation to various
types of gas (Fig. 7)
Should the appliance be pre-set for a different type
of gas than available, proceed as follows:
Replace the injector (fig. 7) with the corresponding type
of gas to be used (see table “User characteristics“);
Adjust to the minimum, use a screwdriver on the
screw placed on the tap (Fig. 8) after turning the tap
to its minimum position.
For LPG (propane) screw tight.
Figure 7
Figure 8
Figure 9

11
User characteristics
Electrical connection
Before connecting the appliance, make sure
the supply voltage marked on the rating Plate
corresponds with the mains supply voltage.
WARNING – THIS APPLIANCE MUST BE EARTHED
Ensure the appliance is plugged into a 1O amp GPO
IMPORTANT
The wires in the main supply lead are coloured
in accordance with the following code:-
Green and Yellow Earth
Blue Neutral
Brown Live
The connections must be made as follows:-
• The wire coloured Green and Yellow must be
connected: to the terminal marked ‘E’ or the earth
symbol or coloured green and yellow.
• The wire coloured Blue must be connected to the
terminal marked ‘N’ or coloured blue or Black.
• The wire coloured Brown must be connected to
the terminal marked ‘L’ or coloured brown or red.
NOTE: The terminals marked ‘SUPPLY’ are for the mains supply wires
and the terminations marked ‘LOAD’ are for the appliance wires.
The electrical outlet is to be positioned in an easily
accessible position adjacent to the appliance.
In the event that it is necessary to replace the mains
supply lead, the replacement must conform to the
specification listed in the Technical Data. Ensure that
the colour code connection is correct and that all
screws are tightened correctly.
Rigid/semi rigid metal connection
Carry out the connection with fittings and metal
pipes (even flexible pipes) so as to obtain counter
stress the inner parts of the appliance.
N.B. – when the installation has been carried out, check the
perfect sealing of the entire connection system, by using a soapy
solution.
Prior to carrying out the electrical connection, please
ensure that:
• the plant characteristics are such as to follow
what is indicated on the matrix plate placed at the
bottom of the working area;
• That the plant is fitted with an efficient earth
connection, following the standards and law
provisions in force. The earth connection is
compulsory in terms of the law.

12
Should there be no cable and/or plug on the
equipment, use suitable absorption material
for the working temperature as well, as indicated
on the matrix plate. Under no circumstance must
the cable reach a temperature above 50°C of the
ambient temperature. If connecting directly to the
mains power supply, fit a multi-pole switch of a
suitable size for the rated capacity with a clearance
distance which completely disconnects the power
line under overvoltage category III conditions,
consistently with the rules of installation (the yellow/
green earth wire must not be interrupted). The plug
or omni polar switch must be easily reached on the
installed equipment.
To avoid all risk, if the power cable becomes
damaged, it must only be replaced by the
manufacturer, by an authorised service centre,
or by a qualified electrician.

13
Maintenance
WARNING: SERVICING SHOULD BE CARRIED
OUT ONLY BY AUTHORISED PERSONNEL
During the warranty period, in case of need all
service intervention should be referred back to the
Kleenmaid Service Department. Please note that
intervention or repair by any unauthorised personnel
will invalidate such warranty.
Before carrying out any maintenance, disconnect
the appliance from the gas and electricity supplies.
If a gas tap becomes stiff to operate, proceed as
follows:
• Remove the control knobs, pan supports, burners
and cooktop fixing screws & clamps.
• Remove the Cooktop from the worktop and
remove any underside protective covers.
• Disconnect the fixings holding the tap to the fascia
panel, separate the assembly, then clean the cone
and seating with a cloth dampened with solvent.
• Lightly smear the cone with high temperature
grease, reassemble into position and rotate a few
times. Remove the cone again and remove any
excess grease making sure that the gas ducts are
not obstructed with grease.
• Carefully reassemble the components and check
for gas soundness.
• If it becomes necessary to replace the gas tap,
proceed as follows:
• Disconnect the appliance as described above.
• Disconnect the gas pipe from the gas tap,
disassemble from the gas rail by removing the
fixing screws.
• When fitting a new tap, ensure that a new gasket
is used.
• Re-connect the gas tap, check for gas soundness
and reassemble the cooktop.
Technical data
Electrical details
Rated Voltage 230V ac 50Hz
Supply Connection 1OAmp GPO
Power Input 0.008 to 0.02kW (depending on model)
Mains supply lead 3 x 0.75mm2Type RR-F <HAR>
marked
A recommended maintenance schedule is
suggested to ensure your product is in optimal
working condition.
Gas details
Connection Type
1/2” BSP
Natural Gas 1.00 kPa – ALTERNATIVE LPG 2.75 kPa

14
Natural gas burner types and power outputs: mj/h
Model Wok Max Rapid Max Semi Rapid
Max Auxiliary Max Total Mj/h Max
GCT6010 12.6 11.2 6.6 3.9 34.3
GCT9010 12.6 11.2 6.6 3.9 40.9
Propane gas burner types and power outputs: mj/h
Model Wok Max Rapid Max Semi Rapid
Max Auxiliary Max Total Mj/h Max
GCT6010 13.0 11.4 6.3 4.0 34.7
GCT9010 13.0 11.4 6.3 4.0 41.0
Jet conversion table natural gas / lpg: mm
Model Wok Rapid Semi Rapid Auxiliary
NG LPG NG LPG NG LPG NG LPG
GCT6010 1.63 1.0 1.55 0.94 1.17 0.70 0.92 0.56
GCT9010 1.63 1.0 1.55 0.94 1.17 0.70 0.92 0.56

Warranty and Service
Domestic Warranty – Full two year warranty
In addition to all statutory rights which you, the Purchaser, have under relevant laws in respect of this
appliance, during the first two years of ownership as the original purchaser of this Kleenmaid appliance,
Compass Capital Services trading as Kleenmaid guarantee that any fault caused by defective material
or workmanship becoming apparent will be rectified free of charge with reference to parts and labour,
provided that all service is performed during normal working hours by Kleenmaid or their designated
Agents. Where the appliance is installed outside the normal servicing area of the above, the Purchaser
must pay for the cost of transporting the appliance to and from the Agent or the Agent’s travel cost to
and from the purchaser’s home.
Commercial Warranty – One year warranty
When this appliance is installed in a commercial application, in addition to all statutory rights which
you, the Purchaser, have under relevant laws in respect of this appliance, during the first one year of
ownership as the original purchaser of this Kleenmaid appliance, Compass Capital Services trading as
Kleenmaid guarantee that any fault caused by defective material or workmanship becoming apparent
will be rectified free of charge with reference to parts and labour, provided that all service is performed
during normal working hours by Kleenmaid or their designated Agents. Where the appliance is installed
outside the normal servicing area of the above, the Purchaser must pay for the cost of transporting the
appliance to and from the Agent or the Agent’s travel cost to and from the purchaser’s home.
What these warranties do not cover
Compass Capital Services trading as Kleenmaid is not responsible for any damage or malfunction
unless caused by a defect in material or workmanship. This includes but is not limited to abuse,
misuse, improper installation and transportation damage. Compass Capital Services trading as
Kleenmaid is not responsible for consequential damages from any malfunction.
This warranty does not cover consumable items, replacement of light globes or glass breakage due
to impact. In case of fractured glass do not use your appliance.
Purchaser’s responsibility
The Purchaser must make the appliance available for servicing and shall bear any costs incurred
for any de-installation and/or re-installation required to make the appliance available for servicing.
Compass Capital Services trading as Kleenmaid is not liable for any consequential damage incurred
during de-installation or re-installation.
Warranty registration and Proof of Purchase.
Please complete warranty details below and retain together with your proof of purchase document.
When requesting service under this warranty the Purchaser agrees that Proof of Purchase of their
Kleenmaid appliance will be necessary in order to make the warranty valid. Inability to provide Proof
of Purchase even though this warranty is in place will not bind Compass Capital Services trading as
Kleenmaid to repair the appliance at no charge under this warranty and will require the Purchaser to
pay for the service costs in full.
Model Number Date of purchase
For service assistance visit
www.kleenmaid-appliances.com.au

Compass Capital Services Pty Limited
trading as Kleenmaid
ABN 96138214525
Level 2, Suite 3,
204 Botany Rd
Alexandria NSW 2015
E: [email protected]
www.kleenmaid-appliances.com.au
Other products available in the
Kleenmaid range of appliances
|Washing machines
|Clothes dryers
|Dishwashers
|Ovens
|Cooktops
|Steam ovens
|Microwave ovens
|
Built in espresso
coffee machines
|Rangehoods
|
Freestanding ranges
|
Sinks
|
Taps