Kleenmaid IVK60 User manual

REF CONSTRUCTEUR 214 9962 9641 05/03
CookingCooking
c o l l e c t i o nc o l l e c t i o n
Instructions for fitting and using
your mixed induction-ceramic
and
Warranty Details
IVK60 - 600mm Induction-ceramic Cooktop
kleemaid99625605.qxd 27/05/03 08:55 Page 1

2
Cooking
c o l l e c t i o n
Congratulations on the purchase of your new appliance.
This appliance has been
designed and manufactured to give you years
of reliable performance.
For best results, carefully read the instructions on how to
install your new appliance. Correct installation will avoid
delays and unnecessary service calls.
Once installation is complete, read this booklet
carefully and get to know the controls and the
features of your new appliance.
We reserve the right to alter the specifications
with no influence on the operation of the
appliance.This instruction manual cannot be
reason for a claim.
kleemaid99625605.qxd 27/05/03 08:55 Page 2

In this Manual,
displays safety
instructions
displays tips and hints
Using your hob in complete safety..........................4
Containers.........................................................6-7
Installing your hob in complete safety...........................8
Using your hob in all simplicity.............................10
Preserving and maintaining your hob....................12
Small problems and solutions...............................13
Cooking ........................................................14-15
List of contents
We have designed this hob for domestic use only.
With a view to constantly improving our products, we reserve the right to make technical and
programming changes or modify the appearance.
This hob is designed solely for cooking food. No asbestos has been used in its manufacture.
We suggest that you should periodically check that there are no objects (glass, paper, etc.) that could
obstruct the air inlet under your induction hob (See fitting).
3
kleemaid99625605.qxd 27/05/03 08:55 Page 3

If your hob is placed above your oven (see "Choice of Installation") thermal
protectors prevent it being used when the oven is being pyro-cleaned.
4
Using your hob in complete safety
We have designed this hob for private use in homes.
With a view to constantly improving our products, we reserve the right to make any changes to their
technical, program or aesthetic features connected with their technical evolution.
These hobs are exclusively designed for cooking and contain no asbestos based
components.
We suggest that you should periodically check that there are no objects (glass, paper, etc.) that could
obstruct the air inlet under your induction hob (See fitting)
HOB safety
•A sensor continuously monitors the
temperature of the components of your hob.
The power output by the hob will automatically
be reduced if this temperature becomes
excessive.
Induction safety area
•You only have to remove the pan from the hob to
stop power instantaneously. Touch the "Off" touch
control to turn off the heating zone completely.
•SAUCEPAN safety
Each unit is equipped with a sensor that conti-
nuously monitors the temperature of the bottom
of the pan, so that overheating is impossible
(empty saucepan, etc.).
•METALLIC OBJECT safety
A small object such as a fork, spoon or a ring
placed on your induction hob by itself is not
detected as a pan. The display flashes and there
is no output power.
Residual heat indicator
The display shows H.
After a prolonged power cut, a light display may
appear.
key for a while. However, the temperature of the
cooking areas may remain high.
WARNING
Do not touch these areas, risk of burns.
Automatic-Stop
Automatic stop is a safety function for your hob. It
starts up automatically if ever you forget to turn off
your cooking.
The letter A is displayed for the heating zone
concerned and the hob will beep for about 2 mi-
nutes. The Awill continue to be displayed until any
control of the zone in question is touched. The hob
will then beep twice to confirm your action.
Power consumed The heating zone
goes out automatically
after
Between 1....4 8 hours
Between 5....7 2 hours
Between 8....9 1hour
kleemaid99625605.qxd 27/05/03 08:55 Page 4
WARNING!
The appliance is not intended for use by young
children or infirm persons without supervision.

+
-
Induced currents
Electronic circuit
Induction coil
5
For the attention of wearers of pacemakers or other active
implants:
The hob complies with all current standards on electromagnetic interference.
Your induction hob is manufactured perfectly in keeping with legal requirements (89/336/CEE
directives). It is designed not to create interference on any other electrical apparatus being used on
condition that the apparatus in question also complies with this legislation.
Your induction hob generates short-range magnetic fields.
To avoid any interference between your induction hob and a pacemaker, the latter must be designed to
comply with relevant regulations.
In this respect, we can only guarantee our own product conformity. Please consult the pacemaker
manufacturer or your doctor concerning its conformity or any possible incompatibility. L
Your induction hob in complete safety
The principles of induction
When your induction hob is switched on and a
heating power has been selected, the electronic
circuits produce induced currents that
instantaneously heat the bottom of the pan that
transfers this heat to the food.
Thus cooking takes place with practically no ener-
gy loss between the induction hob and the food.
If a crack appears in the glass surface, disconnect the appliance immediately to avoid any risk
of electric shock. For disconnecting, remove the fuses or use the cutout switch.
Do not re-use your hob until the glass surface has been changed.
Your hob must never be used as a storage space or cutting surface for any products whatsoever.
When cooking never use aluminium foil and never place products wrapped in aluminium foil or
products deep-frozen in aluminium packs on the hob.
The aluminium will melt and damage your appliance irreparably.
Do not leave empty pans on your hob in case of residual heat or if the hob is turned on by mistake.
Do not connect electrical appliances on plugs close to the hob. Make sure that the power cable is
not in contact with any heating zones.
kleemaid99625605.qxd 27/05/03 08:55 Page 5

6
Induction pan area
You probably already have some suitable pans.
Your induction hob is able to recognise
most types of pans.
Pan test: Place your pan on a zone, for
example at position 4; you know that your pan
is compatible if the display does not flash, but
if it does flash then you cannot use this pan for
induction cooking. You can also test it with a
magnet: if the magnet "sticks" to the base of
the pan, then you can use it for induction
cooking.
Pans compatible with induction are:
• pans made of enamel coated steel with or
without a non-stick coating.
• cast iron pans with or without enamel coated
base.
An enamelled coated base will prevent the glass
top of your hob from getting scratched.
• stainless steel pans designed for induction
cooking.
Most stainless steel pans (saucepans, stewpans,
frying pans, deep frying pans, etc.) are suitable
for induction cooking if they pass the pan test.
• aluminium pans with special base.
Pans which do not have a flat base may be sui-
table, however they must not be badly deformed.
Choose a pan marked with the
logo on its base or packaging to be sure that it is
perfectly suitable for use on your induction hob
under normal conditions of use.
• Note
Glass, ceramic, aluminium pans (without a
special base) and copper pans, and some non-
magnetic stainless steel pans are incompatible
with induction cooking. You will be informed by
the flashing display.
You should choose pans with a thick
flat base for uniform cooking (heat is
better distributed).
Using the cooking zones according to the pan (depending on the model)
Ø18 ..... 24 cm
Ø 22 cm
Ø 16 cm
Ø10 ..... 18 cm
Slow cooking (sauces, creams…).
Preparing small quantities or individual
portions…
Multi-service zone
For small pans
kleemaid99625605.qxd 27/05/03 08:55 Page 6

7
Vitroceramic pan area
The best way to use your ceramic hob
For easy use, we have provided cooking zones
specially adapted to your needs.
However, higher temperatures may be required
for:
- Large quantities
- Cooking with a non-covered casserole.
- Using a glass or ceramic casserole.
And lower temperatures are required for:
- Cooking food products that tend to burn easily
(start with a low temperature that can always be
increased if possible).
- In case of overflowing
(take the lid off, or remove the pan from the heat,
then lower the temperature).
Energy saving:
To finish off cooking touch the control and
reduce back to 0. Leave the pan in place to use
up all the accumulated heat (which saves
energy).
Use a lid whenever possible to reduce any loss of
heat through evaporation.
Automatic cooking zone temperature adjust-
ment
The radiant cooking zone is self-regulating, It
switches itself on and off so as to remain at the
programmed power. Under these conditions the
temperature remains constant and is correctly
adapted to the food you are cooking.
The frequency of self-regulation depends on the
power being used.
Pans and casseroles must be designed for use with electric hobs.
Use pans with flat bases that have good surface contact with the cooking
zone surface. They must be made out of:
- Stainless steel with a thick tri-metal or "sandwich" bottom.
- In aluminium with a thick smooth bottom.
- In enamelled steel.
kleemaid99625605.qxd 27/05/03 08:55 Page 7

8
Installing your hob in complete safety
4mm minimum
air outlet full
width of cooktop
40mm minimum
Induction Hob Bench Top
50mm vent holes into
cabinet on both sides
cabinet on both sides
Vertical divider
Oven cavity must
be air tight at top
Bottom Shelf
under Bench Oven
Kick Board
Above an oven
4 cm mini
Ensure that the unit crossbar does not block the air
passage, make a bevel if necessary.
Above a cupboard or drawer unit
Gap
When installing induction hob above any oven the following ventilation requirements must be observed:
*Divider shelf separating the hob from the oven to be positioned at least 50mm below hob.
*Cooktop must be isolated from any oven cavity ie. under bench.
*A vertical division to be positioned between the divider shelf and the underside of the hob
approximately 300mm from the back of the cupboard.
* Ventilation holes must be drilled into side of adjoining cupboards to allow supply of fresh air to cooktop.
Incorrect installation may result in premature failure of cooktop and will void warranty.
WARNING: The installation instructions must be followed or warranty will be void.
Always ensure that the air vents beneath the hob are kept clear.
Your induction hob must always be adequately ventilated.
kleemaid99625605.qxd 27/05/03 08:55 Page 8

9
Fix the clips into position
(supplied in the sachet).
Installing your hob in complete safety
4 cm mini
26 ,5 /56 /75 cm
49 cm
4 cm mini
4 cm mini
Fitting A seal exists for preventing any
humidity getting under the hob.
-Stick the seal under the rim of
the hob and lower the hob into
position on the worktop.
-This seal is supplied in the
sachet; stick it in place beneath
the hob.
Neutral
Earth
Phase
NL
- 220-240 V monophase
fuse 32
Neutral
Earth
Phase 2
Phase 1
NL1 L2
Separate the 2 phase wires L1 and L2
before connecting
Blue
Green/yellow
Black
- 400 V 2N three-phase
fuse : 16 Amp
Green/yellow
Blue
Black
These hobs are delivered with type H 05 VVF power cable (1.5mm²) with 5 conductors (including a
green/yellow earth wire), which must be connected to the power supply via a plug that complies with
publication CEI 60083 or an all-pole cut-out unit with contacts that open by at least 3mm.
If the cable is damaged, it must be replaced by an authorised Kleenmaid Service Agent or
similarly qualified person for avoiding any possible risk of accident.
When the power is switched on, or after a long power failure, a light code appears on the control panel.
This disappears automatically after about 30 seconds or as soon as any touch control is touched on the
panel. This is normal, as the display is for use by the after-sales service when required. The user must
not take this into account under any circumstances. If the unit has a 3 phase 400 V2N connection, and is
not working correctly, check that the neutral wire is correctly connected. This precaution should also be
taken for all your other electronic apparatus.
The unit must be installed so that the mains plug is easily
accessible.
brown
brown
Connection
58 51
48,8 55,5
6,4
dimensions in cm
Screw the clips into
position as shown
below
Depending on the clip model provided in the bag:
58
6 kW
including 2.8 kW for induction
kleemaid99625605.qxd 27/05/03 08:55 Page 9