Kodak HEALTH SCIENCES X-Omat M43 User manual

HEALTH SCIENCES DIVISION
© Eastman Kodak Company
Publication No. 981088
September 1995
Supersedes 981088
October 1994
INSTALLATION INSTRUCTIONS for the
Kodak X-Omat M43 and M43A PROCESSORS
and the
Kodak X-Omat Clinic 1 PROCESSOR
H130_0009DA

2 September 1995 – 981088
PLEASE NOTE The information contained herein is based on the experience and knowledge relating to the
subject matter gained by Eastman Kodak Company prior to publication.
No patent license is granted by this information.
Eastman Kodak Company reserves the right to change this information without notice, and
makes no warranty, express or implied, with respect to this information. Kodak shall not be
liable for any loss or damage, including consequential or special damages, resulting from any
use of this information, even if loss or damage is caused by Kodak’s negligence or other fault.
Warning
To avoid hazardous conditions, keep floors and floor coverings around your Kodak X-Omat Processors and
associated drains clean and dry at all times. Any accumulation of fluids from mixing tanks, drain lines, etc., should
be cleaned up immediately. In the event of an accumulation of liquid due to backup, overflow, or other malfunctions
of the drain associated with your Kodak X-Omat Processor, call a plumber or other contractor to correct any problem
with the drain. Kodak accepts no responsibility or liability whatsoever for the serviceability of any drain connected
to or associated with a Kodak X-Omat Processor. Such drains are the sole responsibility of the customer.
This equipment includes parts and assemblies sensitive to damage from electrostatic
discharge. Use caution to prevent damage during all service procedures.
Important
This manual is intended for use by qualified service personnel only.

981088 – September 1995 3
Description Page
Table of Contents
Unpacking the PROCESSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing the PROCESSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Moving the PROCESSOR to the Work Area . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing the PROCESSOR on the MOUNTING STAND . . . . . . . . . . . . . . . . 9
Installing the PROCESSOR on a Table Top . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installing the PROCESSOR Through the Wall . . . . . . . . . . . . . . . . . . . . . . . . . 13
Changing the PROCESSOR to 50 or 60 Hz Operation, M43 and M43A Only . . . . . . . . . 32
Installing the Alternate SPROCKET on an M43 or M43A PROCESSOR Only 33
Changing the Input CONNECTOR on the DRIVE MOTOR . . . . . . . . . . . . . . 34
Processor Setup Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Available Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Changing the PROCESSOR Setup Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Installing the DRYER PLENUM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Installing the RACKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Identifying the Parts of the PROCESSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Installing the WASH RACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Installing the FIXER and DEVELOPER RACKS . . . . . . . . . . . . . . . . . . . . . . . 44
Installing the DRYER RACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Leveling the PROCESSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Making the Necessary Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Checking the Electrical Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Important Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Service Requirements for European Installations of the M43 PROCESSOR . . 49
Making the Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Connecting the DRAIN LINES and the Water Supply HOSE
for the Table Top or MOUNTING STAND Installations. . . . . . . . . . . . . . . . . . . . 51
Connecting the HOSES from the REPLENISHMENT TANKS
in Table Top or MOUNTING STAND Installations . . . . . . . . . . . . . . . . . . . . . . . 53
Doing the Water Leak Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Setting the Developer Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Checking and Adjusting the Replenishment Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Installing the KNOBS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Installing the KNOBS on the DRAIN VALVES . . . . . . . . . . . . . . . . . . . . . . . . 64
Installing the DRYER TEMPERATURE CONTROL KNOB . . . . . . . . . . . . . 65
Installing the FEED TRAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Installing the LIGHTTIGHT FEED TRAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Filling the TANKS with the Developer and Fixer Solutions . . . . . . . . . . . . . . . . . . . . . . . 67
Mixing the Chemicals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Filling the FIXER TANK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Filling the DEVELOPER TANK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Final Checkout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Checking for Correct Operation of the PROCESSOR . . . . . . . . . . . . . . . . . . . . 73
Transport Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Setting the Dryer Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

INSTALLATION INSTRUCTIONS
4 September 1995 – 981088

Unpacking the PROCESSOR
981088 – September 1995 5
Section 1: Unpacking the PROCESSOR
Figure 1 Removing the Components [1] Cutthemetalbands, open theshippingcarton,and
remove any packing material.
Important
When removing protective packing material or
wrapping from components, be careful not to cut
through the protective wrapping and damage the
component.
[2] RemovetheitemspackedwiththePROCESSOR.
See publication 1C7052 in the front pocket of
your publications binder for a list of the items
packed with your PROCESSOR model.
[3] Remove:
• shipping carton from around the
PROCESSOR
• any other packing materials
• TOP COVER from the PROCESSOR
• EVAPORATION COVERS for the
DEVELOPER and FIXER RACKS
• 2 SIDE ACCESS PANELS and the BACK
ACCESS PANEL by loosening the
2 SCREWS securing each PANEL
• POWER CABLE (provided with the M43A
only)
H130_0140CA
COVER (2)
EVAPORATION
GUARD
SPLASH
FEED
TRAY
H130_0140CCA
DRYER RACK
metal
bands
PANEL
BACK
ACCESS
TOP
COVER
carton
shipping
SIDE ACCESS
PANEL (2)
EXIT ROLLER
ASSEMBLY

INSTALLATION INSTRUCTIONS
6 September 1995 – 981088
Figure 2 Removing the Tape from the DRYER AIR
TUBES
[4] From the DRYER RACK, remove the 8 pieces of
tape holding the DRYER AIR TUBES in position.
Non-Drive End View
H130_0142GA
DRYER RACK
H130_0142GCA
tape
TUBES (8)
DRYER AIR

Unpacking the PROCESSOR
981088 – September 1995 7
Figure 3 Unpacking the RACKS
[5] Remove the 2 SCREWS securing the WOOD RESTRAINT on the DEVELOPER RACK. Remove the WOOD
RESTRAINT from the DEVELOPER RACK.
[6] Remove the 2 SCREWS securing the WOOD RESTRAINT on the FIXER RACK. Remove the WOOD
RESTRAINT from the FIXER RACK.
[7] Locate the SCREW hole on the drive side of the PROCESSOR that was used to secure the WOOD
RESTRAINT onto the FIXER RACK.
[8] Install the O-RING provided into that hole using the SCREW and WASHER provided. The O-RING will be
used in later procedures to enable you to secure the COVER of the ELECTRICAL BOX in the open position.
See the figure.
[9] Remove the DEVELOPER and FIXER RACKS and any protective packing material.
[10] Cut and remove the STRAP securing the WASH RACK in place.
[11] Remove any remaining protective packing material.
H130_0170DA
DRIVE
ACCESS
PANEL
SIDE
STRAP
O-RING
WASHER
SCREW
WOOD RESTRAINTS
H130_0170DCA
DEVELOPER
RACK
FIXER RACK
WASH RACK
SCREWS (4)

INSTALLATION INSTRUCTIONS
8 September 1995 – 981088
Section 2: Installing the PROCESSOR
Moving the PROCESSOR to the Work Area
Warning
The unpacked, empty PROCESSOR weighs approximately 84 kg (185 lb). Use 2 people to move it. The PUMPS
are heavy and are located in the back of the PROCESSOR. Rotate the PROCESSOR so that each person supports
1⁄2the weight of the PROCESSOR.
[1] Move the PROCESSOR to the work area where you plan to install it. When possible move the PROCESSOR
in its upright position.
(a) If the PROCESSOR does not fit through the door opening of the work area, do the steps below.
1. Check that the BACK ACCESS PANEL and DRIVE SIDE ACCESS PANEL are removed. If not,
loosen the 2 SCREWS on each PANEL and remove the PANEL.
2. Check that the FRONT ACCESS PANEL is installed. The FRONT ACCESS will protect the FILM
DETECTOR ASSEMBLY from damage when moving the PROCESSOR through a narrow door
opening.
3. To reduce space requirements, check that the LEVELING FEET are rotated up into the PROCESSOR
as far as possible.
4. Rotate the PROCESSOR so that the non-drive side faces down. See the figure for the dimensions of
the PROCESSOR with the TOP COVER and PANELS removed.
5. To reduce space requirements even more, unscrew the MOUNTING BRACKET for the
INTERLOCK SWITCH and let the INTERLOCK SWITCH hang inside the PROCESSOR.
Figure 4 Moving the PROCESSOR through a Narrow Door Opening
H130_0133HA
41.3 cm
66.7 cm
(26 1/4 in.)
(16 1/4 in.)
(27 1/4 in.)
69.2 cm
34.3 cm
(13 1/2 in.)
non-drive
FRONT ACCESS
PANEL
side H130_0133HCB
drive
side
BRACKET
MOUNTING
INTERLOCK
SWITCH

Installing the PROCESSOR
981088 – September 1995 9
Important
• Servicing and accessing the PROCESSOR is easiest if you position the PROCESSOR on a Kodak
M35, M43, Clinic 1 MOUNTING STAND.
• If you will not be installing the PROCESSOR on the Kodak M35, M43, Clinic 1 MOUNTING
STAND, see “Installing the PROCESSOR on a Table Top” on Page 12.
• If you will be installing the PROCESSOR through the darkroom wall, see “Installing the
PROCESSOR Through the Wall” on Page 13.
[2] Install the PROCESSOR by following 1 of the 3 procedures outlined on the following pages:
• on a Table Top — see Page 12
• through the wall — see Page 13
• on the M35, M43, Clinic 1 MOUNTING STAND — see below
[3] If you removed the INTERLOCK SWITCH in Step 1a, do the steps below.
(a) Install:
• SIDE ACCESS PANELS
• FRONT ACCESS PANEL
• TOP COVER
(b) Push the MOUNTING BRACKET forward until the BLADE of the TOP COVER fully engages the
INTERLOCK SWITCH. Tighten the 2 SCREWS to secure the BRACKET.
Installing the PROCESSOR on the MOUNTING STAND
[1] Place the PROCESSOR on the MOUNTING STAND with the large holes toward the operator’s work area.
Important
If you will be securing the MOUNTING STAND with SEISMIC BRACKETS, ensure that the MOUNTING
STAND, on its LEVELING FEET, is no more than 2.5 cm (1 in.) above the floor.
[2] Install the 4 LEVELING FEET and 4 LOCK NUTS on the MOUNTING STAND.
(a) Rotate the LEVELING FEET until the MOUNTING STAND is approximately 2.5 - 3.75 cm
(1 - 11⁄2in.) above the FLOOR.
Important
If you will be securing the MOUNTING STAND with SEISMIC BRACKETS, use the FLOOR PLATES provided
with the SEISMIC BRACKET KIT 261413.
[3] Install the FLOOR PLATES under each of the 4 LEVELING FEET of the MOUNTING STAND.
[4] Move the MOUNTING STAND as close to its final position as possible while still maintaining clearance on
all sides of the PROCESSOR for access to components.
[5] Check that the MOUNTING STAND is level both front-to-back and side-to-side.
[6] Once the MOUNTING STAND is level, tighten the 4 LOCK NUTS against the base of the MOUNTING
STAND to secure its height.

INSTALLATION INSTRUCTIONS
10 September 1995 – 981088
Caution
The empty PROCESSOR weighs approximately 84 kg (185 lb).
[7] Position the PROCESSOR on the MOUNTING STAND. Do not allow the LEVELING FEET to fall into the
holes in the TOP of the MOUNTING STAND.
Figure 5 Using the MOUNTING STAND
[8] Raiseand support the non-feed end of thePROCESSOR to gain access to 2 LEVELINGFEET. Use a 5 x 10 cm
(2 x 4 in.) piece of wood that is 1 m (3 ft.) long to support the PROCESSOR.
(a) Position the piece of wood so that:
• it supports the entire width of the PROCESSOR (drive side to non-drive side)
• it is closer to the center of the PROCESSOR than to the back
[9] Remove the NUT from each of the 2 non-feed end LEVELING FEET. Keep the NUTS for later installation.
[10] Remove and discard the LEVELING FOOT on the drive side of the PROCESSOR near the
REPLENISHMENT PUMP.
[11] Install the 7.6 cm (31⁄2in.) LEVELING FOOT (packed with the PROCESSOR) in its place. See Figure 6.
[12] Rotate these 2 LEVELING FEET clockwise until they are fully extended. Use a SOCKET or WRENCH to
ensure that the LEVELING FEET are tight.
[13] Position a SPACER on the TOP of the MOUNTING STAND under each of the 2 LEVELING FEET.
Note
The SPACERS are packed with the MOUNTING STAND.
[14] Lower the raised end of the PROCESSOR by removing the piece of wood supporting it.
[15] Check that the LEVELING FEET are lowered into the SPACERS.
[16] Align the 2 LEVELING FEET and SPACERS with the holes in the TOP of the MOUNTING STAND. Insert
the LEVELING FEET through the holes.
H130_0204BA
LEVELING FEET
holes for
H130_0204BCA
LEVELING FEET
holes for

Installing the PROCESSOR
981088 – September 1995 11
Figure 6 Installing the SPACERS on the Non-Feed End of the PROCESSOR
[17] Repeat Steps 8, 9, and 12 through 16 for other end, the feed end, of the PROCESSOR.
[18] Check that the PROCESSOR is level.
[19] Install the following parts onto the 4 LEVELING FEET by reaching under the TOP of the MOUNTING
STAND:
• 4 WASHERS, provided with the MOUNTING STAND
• 4 NUTS - removed in Step 9
[20] Advance to the appropriate section as outlined below.
(a) If you are installing an M43A or Clinic 1 PROCESSOR for 60 Hz operation, advance to the section
“PROCESSOR Setup Options” on Page 35.
(b) If you are installing an M43A PROCESSOR for 50 Hz operation, advance to the section “Changing the
PROCESSOR to 50 or 60 Hz Operation” on Page 32.
H130_0182HA
LEVELING
FOOT (2)
wood
support
H130_0182HCA
drive side
end
non-feed
SPACER (2)
MOUNTING STAND
REPLENISHMENT PUMP

INSTALLATION INSTRUCTIONS
12 September 1995 – 981088
Installing the PROCESSOR on a Table Top
Warning
The unpacked, empty PROCESSOR weighs approximately 84 kg (185 lb). Use 2 people to move it. The PUMPS
are heavy and are located in the back of the PROCESSOR. Rotate the PROCESSOR so that each person supports
1⁄2the weight of the PROCESSOR.
[1] Check that the work surface is capable of supporting a minimum of 113 kg (250 lb).
[2] Place the PROCESSOR on the work surface with the FRONT ACCESS PANEL facing the operator’s work
area.
(a) Check that all 4 LEVELING FEET are supported.
(b) Refer to the Site Specifications, Publication Number 981087, to check that you have room to access:
• the front of the PROCESSOR
• the ELECTRICAL BOX on the drive side of the PROCESSOR
[3] Locate the 4 FLOOR PLATES packed with the PROCESSOR.
[4] Insert the 4 FLOOR PLATES under the 4 LEVELING FEET of the PROCESSOR.
Figure 7 Installing the FLOOR PLATES
[5] Advance to the appropriate section as outlined below.
(a) If you are installing an M43A or Clinic 1 PROCESSOR for 60 Hz operation, advance to the section
“PROCESSOR Setup Options” on Page 35.
(b) If you are installing an M43A PROCESSOR for 50 Hz operation, advance to the section “Changing the
PROCESSOR to 50 or 60 Hz Operation” on Page 32.
H130_0147BA
PANEL
ACCESS
FRONT
LEVELING FOOT (4)
H130_0147BCA
FLOOR PLATE (4)
NUT (4)

Installing the PROCESSOR
981088 – September 1995 13
Installing the PROCESSOR Through the Wall
Note
• These instructions assume that you are setting the PROCESSOR on a Kodak M35, M43, and Clinic 1
MOUNTING STAND.
• The Kodak X-Omat M43 Through-the-Wall Kit, CAT No. 871-3109, is available and includes:
Planning the Site
[1] Check that the dimensions and location of the hole in the wall match the WALL OPENING in Figure 8 on
Page 14.
[2] Determine the other requirements of your site, such as the location of these items:
• FLOOR DRAIN
• REPLENISHMENT TANKS
– If the REPLENISHMENT TANKS are to be located outside the darkroom, decide whether you will
locate them inside the MOUNTING STAND or outside the MOUNTING STAND.
• main water supply VALVE
• main power supply CIRCUIT BREAKER, which should be located:
– outside of the darkroom
– within sight of the PROCESSOR and be accessible by the operators and service personnel
Qty Item
1 FOAM BLOCK, LIGHT LOCK
2 FOAM GASKET, LIGHT LOCK
6 HOSE CLAMPS #12 for DRAINS
4 HOSE CLAMPS #2 for REPLENISHMENT HOSES
2HOSE, Opaque, 3⁄8in. ID, 3 ft., for REPLENISHMENT HOSES
3HOSE, Opaque, 3⁄4in. ID, 4 ft., for DRAINS
2FITTING, Barbed, 3⁄8in., for REPLENISHMENT HOSES
2 EYEBOLTS
2 NUTS for EYEBOLTS
3FITTING, Barbed, 3⁄4in., for DRAINS
2 WASHERS for LEVELING FEET
2 WASHERS for EYEBOLTS

INSTALLATION INSTRUCTIONS
14 September 1995 – 981088
Figure 8 Checking the Dimensions of the Hole in the Wall, as viewed from the darkroom side
H130_0177DA
127.0 cm
(50 in.)
134.6 cm
(53 in.)
89.5 cm
(35 1/4 in.)
59.1 cm
(23 1/4 in.)
25.4 cm
(10 in.)
91.4 cm
(36 in.)
7.6 cm
(3 in.)
12.7 cm
(5 in.)
78.7 cm
(31 in.)
83.8 cm
(33 in.)
66.0 cm
(26 in.)
30.5 cm
(12 in.)
CAULK
H130_0177DCB
edge of the
WOOD FRAME
FRAME OPENING
for the
PROCESSOR
WOOD FRAME
WALL OPENING
floor

Installing the PROCESSOR
981088 – September 1995 15
Preparing the MOUNTING STAND
[3] Install on the MOUNTING STAND the 4 LEVELING FEET and 4 LOCK NUTS that were packed with the
MOUNTING STAND.
Important
If you will be securing the MOUNTING STAND with SEISMIC BRACKETS, ensure that the LEVELING FEET
extend past the bottom of the MOUNTING STAND by no more than 2.5 cm (1 in.).
[4] Rotate the LEVELING FEET until the FEET extend past the MOUNTING STAND by 3.75 cm (11⁄2in.).
Important
If you will be securing the MOUNTING STAND with SEISMIC BRACKETS, place the 4 FLOOR PLATES
provided with the SEISMIC BRACKET KIT 261413 under the 4 LEVELING FEET of the MOUNTING STAND.
[5] Install the 4 FLOOR PLATES under the 4 LEVELING FEET of the MOUNTING STAND.
Figure 9 Installing FLOOR PLATES under the MOUNTING STAND
H130_0091DA
H130_0091DCC
SEISMIC BRACKET (4)
for the MOUNTING
STAND
LEVELING
PLATE (4)
FOOT (4)
FLOOR

INSTALLATION INSTRUCTIONS
16 September 1995 – 981088
Note
The TOP of the MOUNTING STAND has holes cut in one end to allow for the routing of HOSES and the POWER
CABLE. In through-the-wall installations, these holes must be positioned against the wall. If the
REPLENISHMENT TANKS will be stored inside the MOUNTING STAND, you must remove the TOP of the
MOUNTING STAND and rotate it 180°, as described in Step 6 below. In all other cases, you can use the
MOUNTING STAND as it was shipped.
[6] Check that the TOP of the MOUNTING STAND is positioned correctly to allow for the routing of the HOSES
and the POWER CABLE. If the REPLENISHMENT TANKS will be stored inside the MOUNTING STAND,
do the following steps.
(a) Remove the 9 SCREWS securing the TOP of the MOUNTING STAND.
(b) Rotate the TOP 180°so that the holes are at the closed end of the MOUNTING STAND.
(c) Check that the TOP of the MOUNTING STAND is flush with the closed end of the MOUNTING
STAND.
(d) Install the 9 SCREWS in the second set of pre-drilled holes on the under side of the TOP of the
MOUNTING STAND.
Figure 10 Rotating the TOP of the MOUNTING STAND
ROTATE 180
H130_0205HA
H130_0205HCA
wall
side
TOP
holes
end
closed
STAND
MOUNTING
SCREW (9)

Installing the PROCESSOR
981088 – September 1995 17
Positioning the PROCESSOR on the MOUNTING STAND
Warning
The unpacked, empty PROCESSOR weighs approximately 84 kg (185 lb). Use 2 people to move it. The PUMPS
are heavy and are located in the back of the PROCESSOR. Rotate the PROCESSOR so that each person supports
1⁄2the weight of the PROCESSOR.
[7] Move the MOUNTING STAND near the wall while still maintaining clearance on all 4 sides of the
PROCESSOR for access to components.
(a) Check that the MOUNTING STAND is positioned so that the large holes in the top are toward the wall.
Caution
The empty PROCESSOR weighs approximately 84 kg (185 lb).
[8] Position the PROCESSOR on the MOUNTING STAND with the feed-end towards the wall. Do not allow the
LEVELING FEET to fall into the holes in the TOP of the MOUNTING STAND.
Figure 11 Positioning the PROCESSOR on the MOUNTING STAND
[9] Check that the following parts are removed from the PROCESSOR.
• TOP COVER
• BACK ACCESS PANEL
• FRONT ACCESS PANEL
• DRIVE SIDE ACCESS PANEL
• NON-DRIVE SIDE ACCESS PANEL
[10] Raise and support the non-feed end of the PROCESSOR to gain access to the 2 LEVELING FEET. Use a 5 x
10 cm (2 x 4 in.) piece of wood that is 1 m (3 ft.) long to support the PROCESSOR.
(a) Position the piece of wood so that:
• it supports the entire width of the PROCESSOR (drive side to non-drive side)
• it is closer to the center of the PROCESSOR than to the back
[11] Remove the NUT from each of the 2 non-feed end LEVELING FEET. Keep the NUTS for later installation.
[12] Remove and discard the LEVELING FOOT on the drive side of the PROCESSOR near the
REPLENISHMENT PUMP. See the Figure 11.
[13] Install the 7.6 cm (31⁄2in.) LEVELING FOOT provided with the PROCESSOR.
H130_0204BA
LEVELING FEET
holes for
H130_0204BCA
LEVELING FEET
holes for

INSTALLATION INSTRUCTIONS
18 September 1995 – 981088
[14] Rotate these 2 LEVELING FEET clockwise until they are fully extended. Use a SOCKET or WRENCH to
ensure that the LEVELING FEET are tight.
[15] Position a SPACER, provided with the MOUNTING STAND, on the TOP of the MOUNTING STAND under
each of the 2 LEVELING FEET.
[16] Lower the raised end of the PROCESSOR by removing the piece of wood supporting it.
[17] Check that the LEVELING FEET are lowered into the SPACERS.
[18] Align the 2 LEVELING FEET and SPACERS with the holes in the TOP of the MOUNTING STAND. Position
the LEVELING FEET through the holes.
Figure 12 Installing the SPACERS and Replacing one LEVELING FOOT on the Non-Feed End of the
PROCESSOR
[19] Raise and support the feed end of the PROCESSOR to gain access to the other 2 LEVELING FEET. Use a 5
x 10 cm (2 x 4 in.) piece of wood that is 1 m (3 ft.) long to support the PROCESSOR.
(a) Position the piece of wood so that:
• it supports the entire width of the PROCESSOR (drive side to non-drive side)
• it is closer to the center of the PROCESSOR than to the front
[20] Remove the NUT from each of the 2 feed-end LEVELING FEET. Keep the NUTS for later installation.
[21] Rotate these 2 LEVELING FEET clockwise until they are fully extended. Use a SOCKET or WRENCH to
ensure that the LEVELING FEET are tight.
[22] Insert the HOSES listed below through the holes in the TOP of the MOUNTING STAND:
• 3 DRAIN HOSES
- Use black, opaque DRAIN HOSES if they are going through the wall
- Use clear DRAIN HOSES if draining outside of the darkroom
• a HOSE from the main water supply, not provided
H130_0182HA
LEVELING
FOOT (2)
wood
support
H130_0182HCA
drive side
end
non-feed
SPACER (2)
MOUNTING STAND
REPLENISHMENT PUMP

Installing the PROCESSOR
981088 – September 1995 19
[23] Connect the 3 DRAIN HOSES to the 3 DRAIN VALVE FITTINGS.
(a) Position the CLAMPS, provided in the prepack, so that you can access the SCREWS by inserting a
SCREWDRIVER through the notches in the BRACKET.
(b) Insert the 3 DRAIN HOSES under the 3 NARROW BAND CLAMPS and tighten the 3 SCREWS of the
CLAMPS.
Figure 13 Connecting the DRAIN HOSES
[24] For an M43 PROCESSOR only, install the HOSE ADAPTER and WASHER packed with the PROCESSOR
to the bottom of the WATER INPUT SOLENOID.
[25] Use a standard 5/8 in. NHT HOSE BIB FITTING to connect the HOSE from the main water supply to the under
side of the WATER INPUT SOLENOID.
Note
If you are routing a water supply HOSE under the PROCESSOR, you will need a 90°fitting, not provided, at the
WATER INPUT SOLENOID connection.
Figure 14 Connecting the DRAIN HOSES and the HOSE from the Main Water Supply
H130_0187BA
DRAIN VALVE
FITTING (3)
H130_0187BCA
DRAIN
developer
HOSE
SCREW (3)
BRACKET
DRAIN
wash
HOSE
CLAMP (3)
NARROW BAND DRAIN
HOSE
fixer
H130_0026BA
fixer DRAIN HOSE
wash DRAIN HOSE
water supply HOSE
developer DRAIN HOSE
BIB FITTING
SOLENOID
WATER INPUT
H130_0026BCB

INSTALLATION INSTRUCTIONS
20 September 1995 – 981088
Important
Read the following steps carefully. Determine whether you need to route the REPLENISHMENT HOSES and the
POWER CABLE through the darkroom wall. Do only the steps that are appropriate for your installation
requirements. It is not recommended to route the POWER CABLE through the wall.
[26] Route the developer REPLENISHMENT HOSE, identified by the red WIRE TIE, through the hole under the
developer DRAIN VALVE.
[27] Route the fixer REPLENISHMENT HOSE, identified by the blue WIRE TIE, through the hole under the fixer
DRAIN VALVE.
[28] Position a SPACER on the TOP of the MOUNTING STAND under each of the 2 LEVELING FEET.
[29] Position a EYEBOLT over each SPACER. See the figure for the correct orientation of the EYEBOLTS.
Figure 15 Installing the EYEBOLTS
[30] Lower the raised end of the PROCESSOR by removing the piece of wood supporting it.
[31] Check that the LEVELING FEET are lowered into the SPACERS.
[32] Align the 2 LEVELING FEET and SPACERS with the holes in the TOP of the MOUNTING STAND. Position
the LEVELING FEET through the holes.
[33] Install the following parts onto the 4 LEVELING FEET by reaching under the TOP of the MOUNTING
STAND:
• 4 WASHERS, provided with the MOUNTING STAND
• 4 NUTS, removed in Steps 11 and 20
H130_0183HA
H130_0183HCA
WASHER (4)
NUT (4)
SPACER (2)
support
FOOT (2)
LEVELING wood EYEBOLT (2)
STAND
MOUNTING