Kodak CR 360 User manual

© CARESTREAM HEALTH, INC. 2010
None
{IllustratedPartsList}{Production}{Carestream Health Inc.}{None} Publication No. 6H4869
17MAR2010
Supersedes 6H4869-01
23DEC09
Service Manual
for the
KODAK Point-of-Care CR 360 System
Important
• Qualified service personnel must install this modification.
• See the Service Portal for possible updates before doing this modification.
• When doing the procedures in this document, you must use safe work practices and wear the correct personal
protective equipment (for example, safety eyewear) according to your company’s standard operating
procedures.

Service Guide
26H4869
KODAK Point-of-Care CR 360 System Service Manual
Publication Number: 6H4869
© Carestream Health, Inc., 2010
US FEDERAL LAW RESTRICTS THIS DEVICE TO SALE BY OR ON THE ORDER OF A PHYSICIAN ONLY.
Allrightsreserved.Nopartofthismanualmaybereproducedorcopiedinanyformbyanymeans–graphic,electronic
or mechanical, including photocopying, typing, or information retrieval systems–without written permission of
Carestream Health, Inc.
Use of Manual
The KODAK Point-of-Care CR 360 System is designed to meet international safety and performance standards.
Personnel operating the unitmust have athorough understanding of the proper operation of the system. This manual
has been prepared to aid medical and technical personnel to understand and operatethe system.Do not operate the
system before reading this manual and gaining a clear understanding of the operation of the system. If any part of
this manual is not clear, please contact your Carestream Health representative for clarification.
The Kodak trademark and trade dress are used under license from Kodak.
Carestream Health, Inc.
150 Verona Street
Rochester, NY 14608
Authorized European Representative
Carestream Health France
LES MERCURIALES
40, rue Jean Jaures
93176 BAGNOLET CEDEX
France

6H4869 3
Description Page
Table of Contents
Safety and Regulatory Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
General Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Electrical Hazards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Explosion and Implosion Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Laser Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Recycling the Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Labelling Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
IEC Symbols Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Device-specific Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
CE Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
USA Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
System Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Operational Principles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Component Names and Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Views of the Point-of-Care CR 360. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Component Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Power Line Filter Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
IMCS Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Linear Slide Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Two Types of Linear Screws. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Linear Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Optical Head Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Photo Multiplier Assembly (PM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Loader Stepper Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Roller Drive Motor Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Right and Left Limit Sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Service Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Service Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Removing the Scanner Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Installing the Scanner Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Activating the Scanner Without the Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Activation Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Activating the Scanner Without the Cover (Laser Deactivated) . . . . . . . . . . . . . 26
Before Service Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
After Service Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Activating the Scanner without the Cover (Laser Activated). . . . . . . . . . . . . . . . 27
Before Service Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
After Service Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Replacing the Power Line Filter Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Removing the Power Line Filter Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Installing the Power Line Filter Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Replacing the Fuses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Replacing the Controller Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Service Guide
46H4869
Removing the Controller Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Installing the Controller Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Replacing the IMCS Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Removing the IMCS Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Separating the Sensor Board from the Motion Board . . . . . . . . . . . . . . . . . . . . 37
Installing the IMCS Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Replacing the Photo Multiplier Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Removing the PM Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Installing the PM Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Replacing the Photo Multiplier Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Removing the PM Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Installing the PM Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Replacing the Optical Head Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Removing the Optical Head Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Installing the Optical Head Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Replacing the Linear Screw Type A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Removing the Linear Screw Type A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Installing the Linear Screw Type A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Replacing the Linear Screw Type B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Removing the Linear Screw Type B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Installing the Linear Screw Type B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Test Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Replacing the Linear Motor Type A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Removing the Linear Motor Type A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Installing the Linear Motor Type A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Replacing the Linear Motor Type B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Removing Type B Linear Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Installing the Linear Motor Type B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Replacing the Roller Drive Motor Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Removing the Drive Roller Motor Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Installing the Roller Drive Motor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Replacing the Loader Stepper Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Removing the Loader Stepper Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Installing the Loader Stepper Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Replacing the Laser Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Removing the Laser Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Installing the Laser Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Replacing the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Removing the Power Supply Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Installing the Power Supply Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Replacing the Erase Lamps Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Removing the Erase Lamps Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Installing the Erase Lamps Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Replacing the Erase Lamps Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Installing the Erase Lamps Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

6H4869 5
Test Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Replacing the Erase Lamp Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Removing the Erase Lamp Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Installing the Erase Lamp Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Replacing the Erase Lamps Inverter Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Removing the Erase Lamps Inverter Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Installing the Erase Lamps Inverter Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Replacing the Roof Assembly and Tray Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Removing the Roof Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Removing the Tray Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Installing the Tray Assembly and the Roof Assembly. . . . . . . . . . . . . . . . . . . . . 86
Test Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Replacing the Right and Left Limit Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Removing the Right Limit Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Installing the Right Limit Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Removing the Left Limit Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Installing the Left Limit Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Replacing the LED Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Removing the LED Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Installing the LED Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
LED Indicator Test Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Replacing the Cassette Status Sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Removing the Cassette Status Sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Installing the Cassette Status Sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Cassette Status Sensors Test Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Replacing the Cassette Fixation Lever Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Removing the Cassette Fixation Lever Assembly . . . . . . . . . . . . . . . . . . . . . . . 95
Installing the Casette Fixation Lever Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 97
Replacing the W0 Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Removing the W0 Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Installing the W0 Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
W0 Sensor Test Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Replacing the Z0 Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Removing the Z0 Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Installing the Z0 Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Z0 Sensor Test Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Installing the IGUS Energy Chain. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Testing and Closing the Scanner Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Replacing the Barcode Reader. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Removing the Barcode Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Installing the Barcode Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Calibrations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
The Calibrations Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Equipment Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Origin Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

Service Guide
66H4869
Offset Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
System Gain Tuning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
System Gain Tuning Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
OCPC Process Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
OCPC Process Calibration Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Adjusting the Cassette Release Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Adjustment Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Auto-loop Solenoid Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Solenoid Off Test (Go/No Go) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Solenoid On Test (Touch/No Touch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Adjusting the Plate Pusher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Adjustment Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Preventive Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Cleaning the Rollers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Roller Cleaning Cycles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Roller Cleaning Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Dismissing the Roller Cleaning Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Cleaning the Phosphor Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Cleaning the Phosphor Screens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Cleaning the Scanner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Key Operator Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Accessing Advanced Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
User Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Setup Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Anatomical Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Diagnostics Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
SW Update & Backup Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Backing Up (Export) Scanner and Anatom Settings . . . . . . . . . . . . . . . . . . . . . 145
To Restore (Import) Scanner and Anatom settings:. . . . . . . . . . . . . . . . . . . . . . 145
Updating Firmware, FPGA, and NIOS Settings . . . . . . . . . . . . . . . . . . . . . . . . . 145
Calibration Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Admin Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
About Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
DICOM Settings—Settings Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
DICOM Settings—Destinations Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Electrical Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Block Diagram #1: Modular Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Block Diagram #2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Block Diagram #3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Block Diagram #4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Block Diagram #5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Block Diagram #6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Block Diagram #7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Block Diagram # 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Block Diagram #9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Observable Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Hardware Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163

6H4869 7
Hardware Error Message Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Hardware Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Recommended Action by Field Engineer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Recommended Actions for Field Engineer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Recommended Actions for Field Engineer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Recommended Actions for Field Engineer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Recommended Actions for Field Engineer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Recommended Actions for Field Engineer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Recommended Actions for Field Engineer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Recommended Actions for Field Engineer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Recommended Actions for Field Engineer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Recommended Actions for Field Engineer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Recommended Actions for Field Engineer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Recommended Actions for Field Engineer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Recommended Actions for Field Engineer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Recommended Actions for Field Engineer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Recommended Actions for Field Engineer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
Recommended Actions for Field Engineer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
Recommended Actions for Field Engineer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
Controller and IMCS Embedded Software Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Updating the Controller Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Updating Firmware and FPGA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Updating the IMCS Embedded Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Using the SC Shell Application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Installing the SC Shell Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Establishing Communication Between the Host Computer and the IMCS Board 185
VSP Option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Direct Cable Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
Creating a Communication Terminal in the SC Shell Application. . . . . . . . . . . . 187
Opening the Communication Terminal in the SC Shell Application . . . . . . . . . . 188
Loading Custom Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
Downloading Firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Verifying the Firmware Download. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
Downloading Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Verifying the Macro Download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
Downloading Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
Verifying Parameters Download. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
Measuring the Linear Motor Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
Acceptance Test Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204

Service Guide
86H4869
Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
Preparing the Unit for Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
Dark Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
System Response and Linearity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
Uniformity and Artifacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
Multiple Test Tools: Resolution Grid, Step Wedge, and Contrast Resolution . . 208
Inspecting the Spatial Resolution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
Inspecting the Low Contrast Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
Inspecting the Step Wedge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
Erasure Efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
Image Quality Results Reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
Calibration Results Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
Test Target Tool for Barcode Alignment Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . 213
Publication History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214

Safety and Regulatory Information
6H4869 9
Section 1: Safety and Regulatory Information
Introduction
The information contained herein is based on the experience and knowledge relating to the subject matter gained by
Carestream Health prior to publication. No patent license is granted by this information.
Carestream Health reserves the right to change this information without notice, and makes no warranty, express or
implied, with respect to this information. Carestream Health shall not be liable for any loss or damage, including
consequential or special damages, resulting from any use of this information, even if loss or damage is caused by
Carestream Health's negligence or other fault.
Caution
Cautionspointoutprocedures that you must follow precisely to avoid damage to the system or any of its components,
yourself or others, loss of data or corruption of files in software applications.
Note
Notes provide additional information, such as expanded explanations, hints, or reminders.
Important
Importants highlight critical policy information that affects how you use this guide and this product.
General Safety Guidelines
• This product was designed and manufactured to ensure maximum safety of operation. Operate and maintain it
in strict compliance with the safety precautions and operating instructions contained in this guide.
• This product meets all the safety requirements applicable to medical equipment. However, anyone attempting to
operate the system must be fully aware of potential safety hazards.
• There are no user serviceable parts in this system. The product must be installed, maintained, and serviced by
qualified service personnel according to procedures and preventive maintenance schedules in the product
service manual. If your product does not operate as expected, contact your Service Representative.
• The product in whole or in part shall not be modified in any way without prior written approval from Carestream
Health, Inc.
• Personnel operating and maintaining this system should receive training and be familiar with all aspects of
operation and maintenance.
• To ensure safety, read all user guides carefully before using the system and observe all Cautions, Importants,
and Notes located throughout the guide.
• Keep this guide with the equipment. Reading this guide does not qualify you to operate, test, or calibrate this
system.
• Unauthorized personnel shall not be allowed access to the system.
• If the product does not operate properly or fails to respond to the controls as described in this guide:
– Follow the safety precautions as specified in this guide.
– Stop using the system and prevent any changes to it.
– Immediately contact the service office, report the problem, and await further instructions.
• Use only legally marketed cassettes. Periodically check the quality of the cassettes, and replace if any defects
are apparent.
• The images provided by this system are intended as tools for the trained user. They are explicitly not to be
regarded as a sole incontrovertible basis for clinical diagnosis.
• Beawareofthe product specificationsand of system accuracyandstability limitations.Considertheselimitations
beforemaking a decision based on quantitativevalues. If you have any doubts,consulttheSales Representative.
• This system is Class I continuous operated stationary equipment without applied parts and has one signal input/
output part.

Service Guide
10 6H4869
Electrical Hazards
Caution
• Do not remove or open system covers or plugs. Internal circuits use high voltage capable of causing serious
injury.
• Fuses blown within 36 hours of being replaced by a qualified technician may indicate malfunctioning electrical
circuits within the system. Have the system checked by qualified service personnel. Do not attempt to replace
any fuse.
• Fluids that seep into the active circuit components of the system may cause short circuits that can result in
electrical fires. Therefore, do not place any liquid or food on any part of the system.
Explosion and Implosion Hazards
CautionCaution
• Do not operate the equipment in the presence of explosive liquids, vapors, or gases.
• Do not plug in or turn on the system if hazardous substances are detected in the environment. If these
substances are detected after the system has been turned on, do not attempt to turn off the unit or unplug it.
Evacuate and ventilate the area before turning off the system.
Overheating
Do not block the air circulation around the scanner. Always maintain at least 6 inches (15 cm) clearance around the
scanner to prevent overheating and damage to the system.
Laser Safety Instructions
• During nominal operation, the unit is closed and sealed with a protective cover for safety reasons.
• Duringnominal operation,thecovershould not be removed.Removingof the cover shall be done only for service
purposes, and by a qualified technician for service operations.
• Service operations that do not require the laser should be done without activating the laser unit. Switching OFF
the DIP switch on the laser board will disconnect the power supply to the laser, and deactivate the laser unit for
service operations.
• In case the laser must be operated during service operation, the service technician shall make sure that the
optical unit is located within the scanner drum, where the laser beam is blocked.
Laser Warning
When a service operation is taking place with the cover removed, disconnect the laser according to the procedure in
Activating the Scanner Without the Cover (Laser Deactivated) on Page 26. If the laser must be activated during the
service procedure, wear protective safety glasses at all times. The required laser safety eyewear must be intended
for HeliumNeon/PDT lasers, have an optical density of 4-5 wavelengths of 610-695 nm, and be marked as having
CE approval.

Safety and Regulatory Information
6H4869 11
Recycling the Unit
Contact your local Carestream Health representative or refer to http://recycle.carestreamhealth.com for additional
information on the collection and recovery programs available for this product.
Labelling Summary
IEC Symbols Used
The system may have labels with one or more of the following symbols. These symbols indicate the IEC standards
to which the system conforms.
In the European Union, this symbol indicates that when the last user wishes to discard this
product, it must be sent to appropriate facilities for recovery and recycling.
Safety Labels Consignes de Sécurité
Laser
Laser-emitting product Laser Appareil émetant de laser
Class 3B laser product inside scanner Rayonnement de laser évitez l’exposition au
faisceau laser de la classe 3B. Appareil à laser
de classe 3B a l’intérieur du scanner.
High voltage Haut voltage
Chassis ground stud Point de mise en terre du chassis
Attention: Consult accompanying documents Attention: consulter les documents joints
Warning, Caution – consult accompanying documents
Protective ground points
Power ON
Power OFF
Caution – Electrical shock hazard

Service Guide
12 6H4869
Device-specific Safety Information
Regulatory Information
Introduction
This product conforms to the following safety standards: IEC 601–1 Medical Electrical Equipment General
Requirements for Safety, EN60601–1–2 Medical Electrical Equipment Electro-Magnetic Compatibility Requirements
and Tests, IEC 60825-1 Safety of Laser Products.
This device complies with 21CFR 1040.10.
CE Conformity
This product conforms to the requirements of council directive 93/42/EEC. The KODAK Point-of-Care CR 360 is a
Class I medical device. The KODAK Point-of-Care CR 360 bears the following mark of conformity:
The name and address of the CE representative appears on the back of the front page of this manual.
USA Regulations
The FDA cleared the system for sale in the USA.
Caution
Federal US law restricts this device for sale by or on the order of a physician.
Safety Information Consignes de Sécurité
LIFTING HAZARD
The KODAK Point-of-Care CR 360 scanner
weighs 39 kg (86 lb). Do not try to lift the scanner
by yourself. Always seek assistance from another
person. Lifting equipment that is too heavy may
result in injury to personnel and/or damage to the
scanner.
DANGER POIDS LOURD
Le scanner KODAK Point-of-Care CR 360 pèse
39 kg (86 lb). N’essayez pas de porter le scanner
par vous-même. Demandez toujours de l’aide
d’une autre personne. Porter un équipement trop
lourd peut provoquer des dommages physiques
et/ou endommager le matériel.
WARNING
The KODAK Point-of-Care CR 360 scanner is a
CLASS 1 Laser product.
• Do not remove the scanner cover.
• Cover removal shall be done only by
authorized service personnel!
ATTENTION
Le scanner KODAK Point-of-Care CR 360 est un
produit laser de la Classe 1.
• Ne pas retirer le couvercle du scanner.
• Le retrait du couvercle doit s’effectuer
uniquement par un personnel compétent.

System Description
6H4869 13
Section 2: System Description
Introduction
Throughout this manual the KODAK Point-of-Care CR 360 System will be referred to as the Point-of-Care CR 360.
The Point-of-Care CR 360 is designed for the reading of phosphor X-ray screens (CR) by medical professionals.
The system consists of the Point-of-Care CR 360 scanner and the software package that includes:
• The KODAK QC Software that operates the scanner.
• An image viewing and archiving software package that supports the DICOM 3.1 standard and was approved by
Carestream Health.
• Thesystemfeatures 8 x 10 in., 10 x 12in., 14 x 17 in., 9.5 x 9.5 in.,11x14in.,14x14in.,14x33cm,24 x 30 cm,
and 15 x 30 cm digital image reading and viewing archive.
Note
Throughout this manual Front of the unit refers to the side where the cassettes are inserted. Right and Left are as
viewed when facing the front of the unit.
Operational Principles
The Point-of-Care CR 360 is a digital imaging system for image acquisition and processing of static projection
radiography that uses a phosphor screen with energy storage capability as an X-ray image receptor.
After exposure, a laser beam, which stimulates luminescence proportional to the local X-ray exposure, reads the
screen. The luminescence signal is digitized. The data is then subjected to digital image processing.
The Point-of-Care CR 360 enables the user to read a screen quickly, and then erase it to be ready for the next scan.
The scanner is compact and easy to use.
Using the Point-of-Care CR 360 enables medical professionals to “go digital” without changing their work practices
or X-ray equipment.

Service Guide
14 6H4869
System Overview
Component Names and Descriptions
Part Name Description
Controller Board The controller board is the main board on the scanner. The controller board
connects the scanner to the host PC workstation via the USB port. The
controller board runs the firmware, and receives operational commands from
the host PC workstation via the USB cable, and transforms the commands to
the appropriate scanner hardware commands. The controller board generates
the +/- 15 Vac to the DPMT and the +/- 12 Vac to the IMCS. It builds the
scanned images and sends them via the same USB cable to the PC
workstation. The controller board serves as the link between all peripherals in
the scanner (i.e., Erase lamp, IMCS, Laser Board, and DPMT)
Integrated Motion Control
System (IMCS) Board The motion (IMCS) board controls and drives the four motors: • Loader motor
• Linear motor
• Rotation motor
• Roller drive motor
The IMCS board receives feedback from the encoders and sensors.
The sensor board is a plug-in board in the IMCS board.
Linear Slide Assembly The linear slide assembly moves the optical head and PM assembly along the
X-axis (slow scan) during the scan.
Optical Head Assembly The optical head assembly includes the laser module and the rotation motor
that rotates the laser tube and a mirror during scanning. The laser module’s
beam is reflected by the revolving mirror to different points on the phosphor
screen inside of the drum. Simultaneously, the optical head travels along a
linear axis, so the laser beam covers the full area of the screen one line at a
time (fast scan). Another mirror collects and reflects the light returned from the
screen to the PM assembly window.
Photo Multiplier Assembly (PM) The photo multiplier (PM) tube collects the photons emitted from the screen and
transforms the light into a current, which is then converted to voltage and
digitized to pixel value by an ADC.
Roof Assembly and Tray
Assembly These two interconnected components receive and direct the cassette into position in preparation for loading into the drum.
Power Supply The AC/DC power supply provides DC power to the scanner components.
Loader Stepper Assembly The loader stepper assembly extracts the phosphor screen from the cassette in
preparation for insertion into the drum, and assists in inserting the phosphor
screen into the cassette. It is powered by the loader motor which works in an
open loop (no encoder).
Roller Drive Motor Sub-System The roller drive motor pulls the phosphor screen, when loading the phosphor
screen into the drum, and pulls the phosphor screen back into the cassette
when unloading the phosphor screen back into the cassette. The roller motor
has a closed loop control which enables you to change the motor speed and
thus control the erase time.
Laser The laser beam stimulates the phosphor screen.
Laser Board The laser board activates the optical head assembly. The laser board receives
rotation motor phases and laser power, and enables laser signals. It transfers
the rotation motor encoder signals to the controller board.
Barcode Reader The barcode reader reads the screen size after the cassette is inserted into the
scanner and locked into place.

System Description
6H4869 15
LED Indicator The LED indicator indicates the scanner’s main status such as ready for scan,
erasing, and so on.
Erase Lamps Assembly The erase lamps assembly brightly illuminates the phosphor screen after
scanning, to erase the image so that the screen is ready to be used again.
Erase Lamps Inverter Board The erase lamps inverter board converts the 21 VDC input to high voltage
output which drives the erase lamps (CCFL tubes).
CCFL Board The CCFL board monitors the erase lamps current (CCFL tubes) and the erase
lamps assembly temperature.
Sensor Board The sensor board is a plug-in board in the IMCS board.
Sensors
Roller Motor Forward Limit
Sensor (J502) Forward limit sensor that stops the roller motor upon reaching the end of travel during screen loading.
Autoloop Sensor (J504) Detects that the auto-loop mechanism is in activated position.
Left and Right Limit Sensors
(J515/J516) Left and right limit sensors indicate that the linear slide assembly has reached the end of its travel. The right limit sensor (J516) is Home position.
W0 Sensor (J511) The W0 sensor determines the activation and deactivation of the rollers
according to screen presence at the entrance to the drum.
Z0 Sensor (J505) Detects the presence of the screen in the drum.
Loader Back Sensor (J508) Back limit sensor that stops the roller motor when moving in a backwards
direction.
Cover Safety Interlock
Sensor (J510) Detects presence of system cover. When the cover is not detected, the system motors, laser, and erase assembly will not work.
15x30 Sensor (J512) Detects if the 15 x 30 in. dental adapter is installed.
Cassette In Place Sensor
(J513) Signals to the control system when the cassette is inserted and locked into the scanner.
Cassette Hold Sensor
(J514) Reverse limit sensor that stops the loader motor upon reaching the end of travel position in a forward direction.
Part Name Description

Service Guide
16 6H4869
Views of the Point-of-Care CR 360
Scanner Front View
Scanner Rear View
LED indicator
Drum
Laser board
Lead screw
Roof assembly
Tray assembly
Erase lamps
Erase lamp
board
Controller board
USB outlet
socket
Power cord
Off/On switch
Connector panel
inverter board

System Description
6H4869 17
Scanner Left View
Scanner Right View
PM tube
Roller drive motor
Linear motor
IMCS board
Laser unit
Power supply
unit

Service Guide
18 6H4869
Component Description
Power Line Filter Module
The power line filter module filters the AC supply to the scanner. The power inlet socket, ON-OFF switch, and two
fuses are located on the module.
IMCS Board
The IMCS board is a module stacked in four layers. It comprises the motion board and the sensor board, which is on
the top layer. The IMCS board controls all four scanner motors and is responsible for all scanner sequences: loading,
scanning, erasing, unloading, and ejecting the cassette.
The motion board and sensor board can be replaced either separately or as a single component. The supplied
replacement unit is an entire IMCS board assembly. If you need to replace one of these boards separately you must
first separate the replacement board from the replacement unit.
Sensor Board Connectors
J501 Reserved
J502 Roller Forward Sensor
J503 Reserved
J504 Loop Solenoid
J505 Screen Carriage Sensor (Z0)
J506 Reserved
J507 Reserved
J508 Loader Back Position
J510 Cover Sensor
J511 W0 Sensor
J512 15 x 30 Cassette Adapter Sensor
J513 Cassette Presence Sensor
J514 Cassette Hold Sensor
J515 Left Limit Sensor
J516 Right Limit Sensor (Home Sensor)
J517 Reserved
J519 Reserved
Motion board

System Description
6H4869 19
Linear Slide Assembly
Overview
The linear slide assembly moves the PM assembly and the laser within the drum to read the phosphor screen.
There are two replacement procedures for the linear slide assembly:
• Linear screw replacement. See Replacing the Linear Screw Type A on Page 48.
• Linear motor replacement. See Replacing the Linear Motor Type A on Page 54.
Two Types of Linear Screws
Linear screw
Linear motor
Type A Type B

Service Guide
20 6H4869
Linear Motor
The linear motor operates the linear slide assembly.
Two Types of Linear Motors
Optical Head Assembly
The optical head assembly controls the laser module beam. The laser module beam emits the light to energize the
phosphor screen.
Type A Type B
Optical head
Laser board
assembly
Optical head
connector bracket